Yamaha NS-SW200 Omistajan opas

English Français Deutsch Svenska Italiano Español Nederlands Русский

G

Subwoofer

Caisson de grave

NS-SW300/NS-SW200

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

i En

Thank you for selecting this YAMAHA product.

Please read the following operating precautions before use.

YAMAHA will not be held responsible for any damage and/or

injury caused by not following the cautions below.

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install this unit in a cool, dry, clean place - away from

windows, heat sources, sources of excessive vibration, dust,

moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose this unit to rain or water.

• The voltage to be used must be the same as that specified on

the rear panel. Using this unit with a higher voltage than

specified is dangerous and may cause a fire and/or electric

shock.

• Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and

the wires connected to other equipment. Never pull the

wires themselves.

• When not planning to use this unit for a long period (ie.,

vacation, etc.), disconnect the AC power plug from the wall

outlet.

• To prevent lightning damage, disconnect the AC power plug

when there is an electric storm.

• Since this unit has a built-in power amplifier, heat will

radiate from the rear panel. Place the unit apart from the

walls, allowing at least 20 cm of space above, behind and on

both sides of the unit to prevent fire or damage.

Furthermore, do not position with the rear panel facing

down on the floor or other surfaces.

• Do not cover the rear panel of this unit with a newspaper, a

tablecloth, a curtain, etc., in order not to obstruct heat

radiation. If the temperature inside the unit rises, it may

cause fire, damage to the unit and/or personal injury.

• Do not place the following objects on this unit:

- Glass, china, small metallic, etc.

If glass, etc., falls as a result of vibrations and breaks, it

may cause bodily injury.

- A burning candle etc.

If the candle falls as a result of vibration, it may cause fire

and bodily injury.

- A vessel containing water

If the vessel falls as a result of vibration and water spills,

it may cause damage to the speaker, and/or you may get an

electric shock.

• Do not place this unit where foreign material, such as

dripping water. It might cause fire, damage to this unit, and/

or personal injury.

• Never put a hand or a foreign object into the YST port

located on the right side of this unit. When moving this unit,

do not hold the port, as it might cause personal injury and/or

damage to this unit.

• Never place a fragile object near the YST port of this unit. If

the object falls or drops as a result of the air pressure, it may

cause damage to the unit and/or personal injury.

• Never open the cabinet. It might cause an electric shock,

since this unit uses a high voltage. It might also cause

personal injury and/or damage to this unit. If something

drops into the set, contact your dealer.

• When using a humidifier, be sure to avoid condensation

inside this unit by allowing enough space around this unit or

avoiding excess humidification. Condensation might cause

fire, damage to this unit, and/or electric shock.

• Super-bass frequencies reproduced by this unit may cause a

turntable to generate a howling sound. In such a case, move

this unit away from the turntable.

• This unit may be damaged if certain sounds are

continuously output at high volume level. For example, if

20 Hz-50 Hz sine waves from a test disc, bass sounds from

electronic instruments, etc., are continuously output, or

when the stylus of a turntable touches the surface of a disc,

reduce the volume level to prevent this unit from being

damaged.

• If you hear distortion (i.e., unnatural, intermittent “rapping”

or “hammering” sounds) coming from this unit, reduce the

volume level. Extremely loud playing of a movie

soundtrack’s low frequency, bass-heavy sounds or similarly

loud popular music passages can damage this speaker

syste

m.

• Vibration generated by super-bass frequencies may distort

images on a TV. In such a case, move this unit away from

the TV set.

• Do not attempt to clean this unit with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

• Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

• Install this unit near the wall outlet and where the AC power

plug can be reached easily.

• Secure placement or installation is the owner’s

responsibility. YAMAHA shall not be liable for any

accident caused by improper placement or installation

of speakers.

• VOLTAGE SELECTOR

(Asia and General models only)

The voltage selector switch on the rear panel of this unit

must be set to your local main voltage BEFORE

plugging this unit into the AC main supply. Voltages are

110-120 V/220-240 V.

CAUTION: Read this before operating your unit

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. In this state, this unit is designed to

consume a very small quantity of power.

ii En

English

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY II .........................................................1

Twisted Flare Port...........................................................1

FEATURES......................................................................2

SUPPLIED ACCESSORY..............................................2

PLACEMENT .................................................................2

Subwoofer orientation.................................................2

CONTROLS AND THEIR FUNCTIONS.....................3

CONNECTIONS.............................................................5

Connecting to line output (pin jack) terminal(s)

of the amplifier.......................................................5

Connecting to speaker output terminals

of the amplifier.......................................................7

Connecting to the INPUT1/OUTPUT terminals of the

subwoofer

....................................................................9

System connections ..................................................10

Plugging the subwoofer into an AC outlet

......................10

AUTOMATIC POWER-SWITCHING FUNCTION

.........10

Setting the AUTO STANDBY switch ......................10

ADJUSTING THE BALANCE....................................11

Subwoofer frequency characteristics ........................13

TROUBLESHOOTING................................................14

SPECIFICATIONS.......................................................15

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows: The wire which is coloured BLUE must be

connected to the terminal which is marked with the letter

N or coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED. Make sure that

neither wire is connected to the earth terminal of a three

pin plug.

Information for Users on Collection and Disposal of Old

Equipment

This symbol on the products, packaging,

and/or accompanying documents means

that used electrical and electronic products

should not be mixed with general

household waste.

For proper treatment, recovery and

recycling of old products, please take them

to applicable collection points, in

accordance with your national legislation

and the Directives 2002/96/EC.

By disposing of these products correctly,

you will help to save valuable resources

and prevent any potential negative effects

on human health and the environment

which could otherwise arise from

inappropriate waste handling.

For more information about collection and

recycling of old products, please contact

your local municipality, your waste

disposal service or the point of sale where

you purchased the items.

[Information on Disposal in other

Countries outside the European Union]

This symbol is only valid in the European

Union. If you wish to discard these items,

please contact your local authorities or

dealer and ask for the correct method of

disposal.

Taking care of the speaker

To maintain the spotless glossy surface of the polished

finish, wipe it with a soft, dry cloth. To avoid damage to the

finish, do not apply chemical solvents, such as alcohol,

benzine, thinner, insecticide, etc. Also, do not use a damp

cloth, or any type of cloth that contains chemical solvents,

or place a plastic or vinyl sheet on top of the speaker.

Otherwise, the finish may peel, the color may fade, or the

sheet may stick to the surface.

CONTENTS

1

2

1 En

In 1988, Yamaha brought to the marketplace speaker systems utilizing YST (Yamaha

Active Servo Technology) to give powerful, high quality bass reproduction. This technique

uses a direct connection between the amplifier and speaker, allowing accurate signal

transmission and precise speaker control.

As this technology uses speaker units controlled by the negative impedance drive of the

amplifier and resonance generated between the speaker cabinet volume and port, it creates

more resonant energy (the “air woofer” concept) than the standard bass reflex method. This

allows for bass reproduction from much smaller cabinets than was previously possible.

Yamaha’s newly developed Advanced YST II adds many refinements to Yamaha Active

Servo Technology, allowing better control of the forces driving the amplifier and speaker.

From the amplifier’s point of view, the speaker impedance changes depending on the sound

frequency. Yamaha developed a new circuit design combining negative-impedance and

constant-current drives, which provides a more stable performance and clear bass

reproduction, without any murkiness.

Today’s bass reflex speakers use a Helmholtz resonator to improve their bass reproduction.

However when reproducing bass that is in the frequency region of this Helmholtz

resonator, air moves violently in and out through the port between the interior and exterior

of the speaker, sometimes producing noise due to the turbulent air flow at the end of the

port.

The port and the cabinet resonate at a frequency that is determined by their dimensions and

shape. On the other hand, turbulence in the air flow at the end of the port contains a broad

range of frequency components that are not present in the input signal. This noise occurs

because the broad range of frequency components includes components that match the

resonant frequencies of the port and cabinet, causing strong resonance.

The Twisted Flare Port developed by Yamaha changes the way in which the port widens

toward its end, and also adds a “twist” to suppress airflow turbulence at each end of the port

and thus prevent noise from occurring.

This eliminates the “muddy sound” and “wind noise” that until now have been

characteristic of bass reflex speakers, allowing bass to be reproduced clearly.

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II

High-

amplitude

bass sound

Port

Cabinet

Advanced impedance

Converter

Active Servo

Processing

Amplifier

Signals of low amplitude

Air woofer

(Helmholtz resonator)

Signals

Twisted Flare Port

2 En

English

• This subwoofer system employs Advanced Yamaha

Active Servo Technology II, which Yamaha has

developed for the production of higher quality, super-

bass sound. This super-bass sound adds a more realistic,

theater-in-the-home effect to your stereo system.

• This subwoofer can easily be added to your existing audio

system by connecting to either the speaker terminals or the

line output (pin jack) terminals of the amplifier.

• For effective use of the subwoofer, the subwoofer’s

super-bass sound should be matched to the sounds of

your front speakers. You can create the best sound

quality for various listening conditions by using the

HIGH CUT control and the PHASE switch.

• The Automatic power-switching function saves you the

trouble of pressing the STANDBY/ON button to turn the

power on and off.

• The subwoofer can be linked to a Yamaha component for

simultaneous power on/off operation.

Use the supplied system control cable to connect the

subwoofer to a Yamaha component that features a

system connector jack. When you turn on or off the

power to the connected component, the subwoofer will

also be turned on or off.

• The flared, gently twisting shape diffuses the vortex of

air generated around the edge of the port, creating a

smooth flow of air. This reduces extraneous noise not

present in the original input signal, and provides clear,

accurate low frequency reproduction.

• The subwoofer can also reproduce a bass sound that is

appropriate for the source. (NS-SW300 only)

It features a B.A.S.S. switch that enables you to select a

bass effect that is suitable for the source.

After unpacking, check

that the following

accessory is contained.

FEATURES

SUPPLIED ACCESSORY

System control cable (5 m x 1)

Since the low-end frequencies of audio signals feature long wavelengths, they are almost non-directional to human ears.

The super-bass range does not create a stereo image. Therefore, a single subwoofer may be enough to produce a high-

quality super-bass sound. However, using two subwoofers (similarly to L and R front speakers) can enhance your acoustic

experience.

Place the subwoofer as shown in fig. , or for the optimum effect. : subwoofer : front speaker

Using one subwoofer

Place the subwoofer on the outside of either the left or right

front speaker.

Placing the subwoofer in between the left and right

front speakers

If you are placing the subwoofer in between the left and

right front speakers, position it slightly at an angle toward

the wall for better effect.

Using two subwoofers

Place them on the outside of

each front speaker.

Notes

• This unit features a magnetically shielded design. However, there is still a chance that placing it too close to a CRT-type TV set

might impair picture color. Should this happen, move this unit away from the TV set.

• If the speaker volume is very loud, furniture or window glass may resonate and the subwoofer itself may vibrate. In this case,

lower the volume level. To limit resonance, use a thick curtain or similar cloth that tends to absorb sound vibrations effectively.

Also, changing the subwoofer position may be helpful.

PLACEMENT

Subwoofer orientation

A

B

C

A

or

B

or

C

Note

The placement shown in the figure below is also possible.

However, if the subwoofer system is placed directly facing a wall,

the bass effect may suffer due to phase cancellation caused by

the interference between the direct and reflected sounds.

To prevent this from happening, place the

subwoofer system at an angle.

(Figures , , and ).

A

B

C

There may be a case that you

cannot obtain enough super-bass

sound from the subwoofer due to

standing waves.

3 En

Check the model number of your subwoofer on the label on the rear panel.

CONTROLS AND THEIR FUNCTIONS

1

2

3

4

Top

A

B

56 7 8 9 <

C

D

Rear

NS-SW300

Front

A

B

56 78<

C

D

1

2

3

4

Front

Rear

Top

NS-SW200

4 En

English

CONTROLS AND THEIR FUNCTIONS

Indicator

VOLUME control ( page 11)

Adjusts the volume level. Turn the control clockwise to increase the volume, and

counterclockwise to decrease the volume.

STANDBY/ON switch

While the POWER switch is ON, press this switch to turn on the power to the

subwoofer. The indicator will light up green. Press the switch again to turn off the

power to the subwoofer. The indicator will turn off.

Port ( page 1)

Outputs super-bass sound.

INPUT2 (NORMAL) terminals ( page 5)

Used to input line level signals from the amplifier.

INPUT3 (LFE) terminal ( page 6)

If your amplifier (or receiver) can cut off high frequencies from signals sent to the

subwoofer, connect the amplifier to the subwoofer’s INPUT3 (LFE) terminal.

The HIGH CUT control has no effect on signals input to the INPUT 3 LFE terminal.

AUTO STANDBY (HIGH/LOW/OFF) switch ( page 10)

This switch is originally set to the OFF position. By setting this switch to the HIGH or

LOW position, the subwoofer’s automatic power-switching function operates. If you

do not need this function, leave this switch in the OFF position.

Note

Be sure to set the POWER switch to OFF before you set the AUTO STANDBY switch.

PHASE switch ( page 11)

This switch is to be set to the REV (reverse) position. However, depending on your speaker

system or listening conditions, there may be a case when better sound quality is obtained by

setting this switch to the NORM (normal) position. Select the best position by ear.

B.A.S.S. (Bass Action Selector System) switch (NS-SW300 only)

( page 11)

When this switch is set to MUSIC, the bass sound in audio

software is well reproduced. When the switch is set to

MOVIE, the bass sound in video software is well reproduced.

SYSTEM CONNECTOR jack ( page 10)

Connect the supplied system control cable here. If you use the system control cable to

connect a subwoofer to a Yamaha component (that features a system connector jack),

turning on or off the power to the connected component automatically turns the

subwoofer on or off.

OUTPUT (TO SPEAKERS) terminals ( page 7)

Can be used for connecting to the main speakers. Signals at the INPUT1 terminals are

sent to these terminals.

INPUT1 (FROM AMPLIFIER) terminals ( page 7)

Used to connect the subwoofer with the speaker terminals of the amplifier.

HIGH CUT control ( page 11)

Adjusts the high frequency cut off point.

Frequencies higher than the frequency selected by this

control are all cut off (and not output).

POWER switch

During normal usage, set this switch to ON. If you plan not to use the subwoofer for a long

period of time, set the switch to OFF.

Green:

Red:

Off:

The subwoofer is turned on.

The Automatic power-switching function has activated, and the subwoofer

is in standby mode.

The subwoofer is turned off.

The subwoofer uses a small amount of power in standby mode.

* One graduation

of this control

represents 10 Hz.

5 En

Choose one of the following connection methods most suitable for your audio system.

Choose this method if your amplifier has line output (pin jack) terminal(s).

( page 5, 6)

Choose this method if your amplifier has no line output (pin jack)

terminals. ( page 7, 8)

Notes

• Unplug the subwoofer and other audio/video components before making connections, and do

not plug them in until all connections are completed.

• Connecting methods and terminal names on your component (such as an amplifier or receiver)

may be different from those used in this book. Please refer to the owner’s manual that came

with your component.

• All connections must be correct, that is to say L (left) to L; R (right) to R; “+” to “+” and “–” to “–”.

Example: Connecting one subwoofer

Use a commercially-available Mono pin cable (1) or a commercially-available Audio pin cable (2) to make the connections.

• Connect the SUBWOOFER (or LOW PASS, etc.) terminal on the rear of the amplifier (or AV receiver) to the /MONO INPUT2 terminal of the subwoofer using a commercially-

available Mono pin cable (1).

Alternatively,

•

When connecting the subwoofer to the SPLIT SUBWOOFER terminals (

featuring L and R channels) on the rear panel of the amplifier, use a commercially-available Audio pin cable (2)

to connect the

/MONO INPUT2 terminal to the “L” side, and the INPUT2 terminal to the “R” side of the SPLIT SUBWOOFER terminals.

Note

Audio signals input from the /MONO and INPUT 2 terminals on the subwoofer will not be output from the OUTPUT (TO SPEAKERS) terminals.

CONNECTIONS

1

2

Connecting to line output (pin jack) terminal(s) of the amplifier

1

2

1 Mono pin cable

2 Audio pin cable

Subwoofer

Amplifier or

receiver

NS-SW300

1

2

1

Mono pin cable

2 Audio pin cable

Subwoofer

Amplifier or

receiver

NS-SW200

6 En

English

Example: Connecting two subwoofers

Connecting to the INPUT3 (LFE) terminal

If your amplifier (or receiver) can cut off high frequencies from signals sent to the subwoofer, connect the

amplifier to the subwoofer’s INPUT3 (LFE) terminal.

This will promote higher sound quality because the signal routing in the subwoofer is shortened by bypassing

the built-in HIGH CUT circuit.

1

Mono pin cable

1

Subwoofer

Amplifier or

receiver

NS-SW300

1 Mono pin cable

1

Subwoofer

Amplifier or

receiver

NS-SW200

NS-SW300 NS-SW200

7 En

■ Example: Connecting the subwoofer to an amplifier that features one set of speaker output terminals

Use speaker cables to connect the speaker output terminals of the amplifier to the subwoofer’s INPUT 1 (FROM AMPLIFIER) terminals. Connect the front speakers to the subwoofer’s

OUTPUT (TO SPEAKERS) terminals. Although the subwoofer is connected between the front speakers and the amplifier, the sound volume or quality will not be affected.

Connecting one subwoofer

Connecting to speaker output terminals of the amplifier

2

Right front

speaker

Subwoofer

Amplifier or

receiver

Speaker output

terminals

Left front

speaker

NS-SW300

Right front

speaker

Left front

speaker

Speaker output

terminals

Amplifier or

receiver

Subwoofer

NS-SW200

8 En

English

Connecting two subwoofers

Right front

speaker

Left front

speaker

Subwoofer

Speaker output

terminals

Amplifier or

receiver

Subwoofer

NS-SW300

Right front

speaker

Left front

speaker

Subwoofer Subwoofer

Speaker output

terminals

Amplifier or

receiver

NS-SW200

■ Example: Connecting the subwoofer to an amplifier featuring two sets of speaker output terminals (A and B) that can output sound signals

simultaneously

Set the amplifier so that both sets of speaker output terminals (A and B) will output sound signals simultaneously. Then, connect the front speakers to terminals A, and connect the

subwoofer to terminals B.

Note

If your amplifier features two sets of speaker output terminals that do NOT output sound signals simultaneously, please refer to the example for connecting an amplifier that has only one set of

speaker output terminals (see the figure on the left).

9 En

Notes

• Make sure that the “+” and “–” polarity markings of the speaker cables are observed and set

correctly. If these cables are reversed, the sound will be unnatural and lack bass.

• Do not let the bare speaker wires touch each other, because this could damage the subwoofer

or the amplifier.

• If the connections are faulty, no sound will be heard from the subwoofer or the speakers. Do

not insert the insulation into the hole. Sound may not be produced.

• To avoid accidents resulting from tripping over loose speaker cables, fix them to the floor.

■ Before connecting

Remove the insulation at the tip of the speaker cable, then twist the core wires together so

that they will not become disarrayed and short-circuited.

Remove about 15 mm (5/8") of insulation.

Remove about 10 mm (3/8") of insulation.

■ How to connect

1. Loosen the terminal’s knob, as shown in the figure.

2. Insert the bare wire.

3. Tighten the knob.

4. Test the firmness of the connection by pulling lightly

on the cable at the terminal.

1. Press and hold the terminal’s tab, as shown

in the figure.

2. Insert the bare wire.

3. Release your finger from the tab to allow it

to lock securely on the cable’s wire end.

4. Test the firmness of the connection by

pulling lightly on the cable at the terminal.

Connecting to the INPUT1/OUTPUT terminals of the subwoofer

15 mm /

10 mm

Good No Good

NS-SW300

NS-SW200

■ Connecting the banana plug

(NS-SW300 only)

1. Tighten the terminal knob.

2. Simply insert the banana plug into the terminal.

2

1

3

Red:

positive (+)

Black:

negative (

–)

NS-SW300

2

1

NS-SW200

3

1

2

10 En

English

If you use the included system control cable to connect a subwoofer to a Yamaha

component (that features a system connector jack such as a YSP series component or

Yamaha receiver), turning on or off the power to the connected component automatically

turns the subwoofer on or off.

Connection example

How the System Connection works

Notes

• For this feature to be available, the POWER switch on the rear panel and the STANDBY/ON

switch on the top panel ( page 3) must be set to ON.

• Powering on/off via the system connection takes priority over the Automatic power-switching

function. (While the unit is turned on, the Automatic power-switching function is enabled.)

• To modify the settings of the connected components, please refer to the owner’s manual that

came with the respective component.

After all connections are completed, plug

the subwoofer and other audio/video

components into AC outlets.

This function automatically places the subwoofer in standby mode if the subwoofer does

not detect a signal from the amplifier for a certain period of time. The subwoofer

automatically turns on as soon as it detects a signal from the amplifier.

The Automatic power-switching function works as follows when the AUTO STANDBY

(HIGH/LOW/OFF) switch is set to LOW or HIGH. (Normally, set the switch to LOW.)

How the Automatic power-switching function works

*1

When the Automatic power-switching function is enabled, the subwoofer will detect a bass signal input of

below 200Hz (such as sound effects of explosion in action movies, bass guitar or bass drum sound, etc.).

*2

This value may vary depending on the system environment. For example, it may be affected by noise

generated from other equipment.

Note

For this feature to be available, the POWER switch on the rear panel and the STANDBY/ON

switch on the top panel ( page 3) must be set to ON.

Note

Be sure to set the POWER switch to OFF before you set the AUTO STANDBY switch.

LOW: The Automatic power-switching function activates at a certain level of input signal.

To enable the function, select this position.

HIGH:If the Automatic power-switching function does not work well when the AUTO

STANDBY switch is set to LOW, select this position. If the function still does not

work, slightly raise the LFE LEVEL on the amplifier.

OFF:

The Automatic power-switchingy function may unexpectedly activate due to the

system environment, for example, if the subwoofer detects noise generated from the

peripheral components. In this case, select this position to disable the Automatic power-

switching function, and manually turn the unit on or off by using the POWER switch.

Notes

• The subwoofer uses a small amount of power in auto-standby mode.

• If you plan not to use the subwoofer for a long period of time, set the POWER switch on the

rear panel to OFF, or unplug the power cable from the AC outlet.

System connections

Turning on the power to the connected component will automatically turn on the subwoofer.

* The indicator lights green.

Turning off the power to the connected component will automatically turn off the subwoofer.

* The indicator turns off.

Plugging the subwoofer into an AC outlet

Subwoofer

Supplied system

control cable

Yamaha YSP series component or receiver

To AC outlet

AUTOMATIC POWER-SWITCHING FUNCTION

The subwoofer automatically enters standby mode if it does not receive an input signal

(*1) from the amplifier for 7 or 8 minutes (*2).

* The indicator color changes from green to red.

When the subwoofer detects an input signal (*1) from the amplifier, the subwoofer

automatically turns on. * The indicator color changes from red to green.

Setting the AUTO STANDBY switch

11 En

To achieve natural sound with an effective super-bass component, you must adjust the volume and tone balance between the subwoofer and the front speakers. Follow the procedure

described below. If your amplifier or other component connected to the system features subwoofer settings, make the appropriate settings on that component.

ADJUSTING THE BALANCE

Rear panel

NS-SW300

Rear panel

NS-SW200

12 En

English

ADJUSTING THE BALANCE

1. Set the VOLUME control to minimum (0).

2. Turn on the power to the component(s) connected to the subwoofer.

If the component is connected to the subwoofer’s SYSTEM CONNECTOR jack, turn

on the power to that component.

3. Make sure that the POWER switch is set to the ON position, then set the STANDBY/

ON switch to ON.

* The indicator lights green.

4. Play a source that contains low-frequency components and adjust the output level of

the front speakers using the amplifier’s volume control to the desired listening level.

(Set all tone controls to flat.)

5. Adjust the HIGH CUT control to the position where the desired response can be

obtained.

Normally, set the control to a level a little higher than the front speaker’s rated

minimum reproducible frequency*.

* The front speaker’s rated minimum reproducible frequency can be looked up in the speakers’ catalog

or owner’s manual.

* The HIGH CUT control has no effect on signals input to the INPUT 3 LFE terminal.

6. Increase the volume gradually to adjust the volume balance between the subwoofer and

the front speakers.

Normally, set the control to a level where you can obtain a little more bass effect than

when the subwoofer is not used.

7. Set the PHASE switch to the position which yields the more natural (or preferable)

phasing.

8. Set the B.A.S.S. switch to “MOVIE” or “MUSIC” according to the played source.

(NS-SW300 only)

MOVIE:

When a movie type source is played, the low-frequency effects are enhanced to allow

listeners to enjoy a more powerful sound. (The sound will be richer and deeper.)

MUSIC:

When an ordinary music source is played, the excessive low-frequency components are

cut off to make the sound clearer. (The sound will carry less bass and reproduce the

melody line more clearly.)

Note

Once the volume balance between the subwoofer and the front speakers is adjusted, you can

adjust the volume of your entire sound system by using the amplifier’s volume control.

However, if you replace the front speakers, you will need to make this adjustment again.

PHASE switch

In most situations, set this switch to select the reverse mode. However, depending

on your speaker systems or listening condition, there may be a case when better

sound quality is obtained by selecting the normal mode. Select the better mode by

monitoring the sound.

13 En

The figures below show the optimum adjustment of each control and the frequency characteristics when the subwoofer is combined with a typical front speaker system.

* These diagrams do not depict actual frequency response characteristics.

Subwoofer frequency characteristics

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT 40 Hz

HIGH CUT 90 Hz

HIGH CUT 140 Hz

■ When combined with 10 cm (

4"

) or 13 cm (5")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW300

PHASE

Frequency response graph*

(70 Hz) (REV)

Front

speaker

■ When combined with 20 cm (8") or 25 cm (10")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW300

Frequency response graph*

PHASE

Front

speaker

(50 Hz) (REV)

NS-SW300

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT 50 Hz

HIGH CUT 100 Hz

HIGH CUT 150 Hz

■ When combined with 10 cm (

4"

) or 13 cm (5")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW200

PHASE

Frequency response graph*

(70 Hz) (REV)

Front

speaker

■ When combined with 20 cm (8") or 25 cm (10")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW200

Frequency response graph*

PHASE

Front

speaker

(50 Hz) (REV)

NS-SW200

14 En

English

Refer to the chart below if this unit does not function properly.

If the instructions given below do not help, or if the problem you are experiencing is not listed below, turn off the power to the unit, disconnect the power cord and contact an authorized

YAMAHA dealer or service center.

TROUBLESHOOTING

Problem Cause What to Do

Power is not supplied

even though the

STANDBY/ON switch

is set the ON position.

The power plug is not securely

connected.

Connect it securely.

The POWER switch is set to the

OFF position.

Set the POWER switch to the

ON position.

The subwoofer does

not turn on

automatically via the

system connection.

The system control cable is not

connected properly or securely.

Connect the system control

cable properly.

The POWER switch is set to

OFF.

Set the POWER switch to ON.

No sound. The volume is set to minimum. Increase the volume.

Speaker cables are not

connected securely.

Connect speaker cables securely.

Low range sound is too

soft or not heard.

Speaker cables are not

connected correctly.

Connect them correctly, that is L

(left) to L; R (right) to R; “+” to

“+” and “–” to “–”.

The PHASE switch is not set

correctly.

Set the PHASE switch to the

other position.

A source sound with little bass

frequency content is being

played.

Play a source sound with bass

frequencies.

Set the HIGH CUT control to a

higher position.

The sound is influenced by

standing waves.

Relocate the subwoofer or

change its positioning angle.

No bass frequency content is

being output from the amplifier.

Check the bass output setting of

the amplifier.

The subwoofer does

not turn on

automatically.

The POWER switch is set to the

OFF position.

Set the POWER switch to the

ON position.

The STANDBY/ON switch is

set to the STANDBY position.

Set the STANDBY/ON switch

to the ON position.

The AUTO STANDBY switch

is set to the OFF position.

Set the AUTO STANDBY

switch to the HIGH or LOW

position.

The level of input signal is too

low.

Set the AUTO STANDBY switch

to the HIGH position, and increase

the output level of the amplifier.

No bass frequency content is

being output from the amplifier.

Check the bass output setting of

the amplifier.

The subwoofer does

not enter standby

mode automatically.

Noise generated from external

appliances etc., is activating the

subwoofer.

Move the subwoofer farther away

from such appliances, and/or

reposition the connected speaker

cables.

Set the AUTO STANDBY switch

to the HIGH or LOW position.

The AUTO STANDBY switch is

set to the OFF position.

Set the AUTO STANDBY

switch to the HIGH or LOW

position.

The subwoofer enters

standby mode

unexpectedly.

The level of input signal is too

low.

Set the AUTO STANDBY

switch to the HIGH position, and

increase the output level of the

amplifier.

The subwoofer turns

on unexpectedly.

Noise generated from external

appliances etc., is activating the

subwoofer.

Move the subwoofer farther

away from such appliances, and/

or reposition the connected

speaker cables.

If the AUTO STANDBY switch

is set to HIGH, set it to LOW.

Alternatively, set the AUTO

STANDBY switch to the OFF

position.

An object has fallen

into the port.

Do not try to remove the object.

Attempting to remove the

object may cause a malfunction.

Contact an authorized

YAMAHA dealer or service

center.

Problem Cause What to Do

15 En

Type ..........................................................Advanced Yamaha Active Servo Technology II

Driver............................................................................................25 cm (10") cone woofer

Magnetic shielding type

Amplifier Output (100 Hz, 5 ohms, 10% THD) .................................................... 250 W

Frequency Response................................................................................... 20 Hz - 160 Hz

Power Supply

U.K. and Europe models ......................................................................AC 230 V, 50 Hz

Australia model ....................................................................................AC 240 V, 50 Hz

China model .........................................................................................AC 220 V, 50 Hz

Asia and General models ..........................................AC 110-120/220-240 V, 50/60 Hz

Power Consumption................................................................................................... 80 W

Standby Power Consumption........................................................................0.3 W or less

Dimensions (W × H × D)...................350 × 366 × 420 mm (13-3/4" × 14-3/8" × 16-1/2")

Weight .....................................................................................................18.0 kg (39.7 lbs.)

Type ..........................................................Advanced Yamaha Active Servo Technology II

Driver..............................................................................................20 cm (8") cone woofer

Magnetic shielding type

Amplifier Output (100 Hz, 5 ohms, 10% THD) .................................................... 130 W

Frequency Response................................................................................... 28 Hz - 200 Hz

Power Supply

U.K. and Europe models ......................................................................AC 230 V, 50 Hz

Australia model ....................................................................................AC 240 V, 50 Hz

China model .........................................................................................AC 220 V, 50 Hz

Asia and General models ..........................................AC 110-120/220-240 V, 50/60 Hz

Power Consumption................................................................................................... 67 W

Standby Power Consumption........................................................................0.3 W or less

Dimensions (W × H × D)......................... 290 × 306 × 351 mm (11-3/8" × 12" × 13-7/8")

Weight .....................................................................................................11.2 kg (24.7 lbs.)

Please note that all specifications are subject to change without notice.

SPECIFICATIONS

NS-SW300

NS-SW200

i Fr

Nous vous remercions d’avoir choisi ce produit YAMAHA.

Lisez attentivement les précautions d’utilisation suivantes.

YAMAHA décline toute responsabilité en cas de

dommages et/ou de blessures découlant du non respect de

ces consignes.

• Pour utiliser l’appareil au mieux de ses possibilités, lisez

attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

• Installez cet appareil dans un endroit frais, sec et propre,

à l’écart des fenêtres et à l’abri des sources de chaleur,

des vibrations, de la poussière, de l’humidité et du froid.

Évitez toute source de bruit électrique (transformateurs,

moteurs). Pour éviter un incendie ou une électrocution,

n’exposez pas cet appareil à la pluie ni à l’humidité.

• La tension à utiliser est indiquée sur le panneau arrière.

Il est dangereux d’utiliser cet appareil avec une tension

supérieure à celle spécifiée, car vous risquez de

provoquer un incendie et/ou de vous électrocuter.

• Ne forcez pas sur les prises, les commandes ou les câbles

de connexion. Lorsque vous déplacez cet appareil,

veillez tout d’abord à débrancher la prise et les câbles

connectés à un autre équipement. Ne tirez jamais sur les

câbles mêmes; saisissez toujours leur fiche.

• Si vous n’utilisez pas cet appareil pendant une période

prolongée (par exemple lorsque vous partez en vacances),

débranchez le câble d’alimentation de la prise secteur.

• En cas d’orage, débranchez le câble d’alimentation de la

prise secteur afin de ne pas endommager l’appareil.

• Cet appareil est muni d’un amplificateur de puissance

intégré et dégage donc de la chaleur par son panneau arrière.

N’installez pas l’appareil trop près d’un mur ; laissez au

moins 20 cm au dessus, derrière et sur les côtés afin d’éviter

tout risque d’incendie. Veillez en outre à ne pas placer le

panneau arrière face au sol ou à une autre surface.

• Ne couvrez pas le panneau arrière de cet appareil avec un

journal, une nappe, un rideau, etc., afin d’éviter

l’accumulation de chaleur à l’intérieur de l’appareil.

L’augmentation de la température interne peut

provoquer un incendie ou endommager l’appareil.

• Ne placez pas les objets suivants sur l’appareil :

- Des objets en verre, en porcelaine, de petits objets

métalliques, etc.

Les vibrations risqueraient de faire tomber ces objets et

de causer des blessures.

- Une bougie se consumant, etc.

Si la bougie venait à tomber sous l’effet des vibrations,

cela pourrait provoquer un incendie et des blessures.

- Un récipient contenant de l’eau

Si le récipient venait à tomber sous l’effet des

vibrations et que l’eau se répande, ceci risquerait

d’endommager l’enceinte et/ou de provoquer une

électrocution.

• Évitez de placer cet appareil à proximité de substances

dangereuses. Vous risquez de provoquer un incendie ou

de vous blesser.

• N’introduisez jamais votre main ou un objet dans le port

YST situé sur le côté droit de l’appareil. Lorsque vous

déplacez l’appareil, veillez à ne pas le saisir par ce port ;

vous risquez de vous blesser et/ou d’endommager

l’appareil.

• Ne placez aucun objet fragile à proximité du port YST de

cet appareil. Si l’objet tombe à cause de la pression de

l’air, vous risquez d’endommager l’appareil ou de vous

blesser.

• N’ouvrez le coffret sous aucun prétexte. Vous risquez de

vous électrocuter, car cet appareil fonctionne sous haute

tension. Vous risquez également de vous blesser et/ou

d’endommager l’appareil. Si un objet tombe par mégarde

à l’intérieur de l’appareil, contactez votre revendeur.

• Si vous utilisez un humidificateur, veillez à éviter la

condensation à l’intérieur de l’appareil. Pour cela, laissez

de l’espace autour de l’appareil et évitez une trop forte

humidification. La condensation peut provoquer un

incendie, une électrocution ou endommager l’appareil.

• Les très basses fréquences produites par cet appareil

peuvent provoquer un effet Larsen quand vous utilisez

une platine. Le cas échéant, éloignez l’appareil de la

platine.

• Vous risquez d’endommager l’appareil si certains sons

sont continuellement émis à un volume important. Par

exemple, si vous reproduisez continuellement les ondes

sinusoïdales d’un disque de test comprises entre 20 Hz et

50 Hz ou les graves d’instruments électroniques, ou si

l’aiguille d’une platine touche la surface d’un disque,

réduisez le niveau de volume afin de ne pas endommager

l’appareil.

• Si vous remarquez une distorsion du son (notamment

lorsque le son manque de naturel, ou si des petits coups

secs intermittents ou un “martèlement” se produisent),

diminuez le volume. La reproduction des sons de basses

fréquences de forte intensité contenus dans les bandes

originales de films à un volume excessif risque

d’endommager cette enceinte.

• Les vibrations générées par les très basses fréquences

risquent de déformer les images sur un téléviseur. Le cas

échéant, éloignez l’appareil du téléviseur.

• Ne nettoyez pas l’appareil au moyen de solvants

chimiques, car vous risquez d’endommager la finition.

Utilisez un chiffon propre et sec.

• Lisez attentivement la section “DÉPANNAGE” avant de

conclure que l’appareil est défectueux.

• Installez cet appareil à proximité d’une prise secteur et

dans un endroit où le câble d’alimentation est facilement

accessible.

• L’utilisateur est entièrement responsable de la mise

en place et de l’installation correctes du système.

YAMAHA décline toute responsabilité en cas

d’accident provoqué par une mise en place ou une

installation inadéquates de l’enceinte.

• VOLTAGE SELECTOR

(Modèles standard et modèles pour l’Asie uniquement)

Vous devez régler le sélecteur de tension situé sur le

panneau arrière de l’appareil conformément à la

tension dans votre pays AVANT de brancher

l’appareil au réseau électrique. Ce sélecteur permet

de choisir les tensions suivantes: 110-120 V/220-

240 V.

ATTENTION: lisez les consignes suivantes avant d’utiliser l’appareil.

Sivu latautuu ...

Yamaha NS-SW200 Omistajan opas

Tämä käsikirja sopii myös

Yamaha NS-SW200 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat