Dometic CAM200 Käyttö ohjeet

Tyyppi
Käyttö ohjeet
CAM200
Rear View Video Camera
Installation and Operating Manual . . . . . 13
Rückfahrvideokamera
Montage- und Bedienungsanleitung . . . 21
Caméra vidéo de recul
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . 29
Cámara de vídeo de marcha atrás
Instrucciones de montaje y de uso . . . . . 37
Câmara de marcha-atrás
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . 45
Videocamera per la retromarcia
Istruzioni di montaggio e d’uso . . . . . . . . 53
Achteruitrijvideocamera
Montagehandleiding en
gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 61
Bakvideokamera
Monterings- og betjeningsvejledning. . . 69
Backningsvideokamera
Monterings- och bruksanvisning. . . . . . . 77
Ryggevideokamera
Monterings- og bruksanvisning . . . . . . . 85
Peruutusvideokamera
Asennus- ja käyttöohje. . . . . . . . . . . . . . . 93
Видеокамера заднего вида
Инструкция по монтажу
и эксплуатации. . . . . . . . . . . . . . . . . . . . .101
Kamera cofania
Instrukcja montażu i obsługi . . . . . . . . . 109
Cúvacia kamera
Návod na montáž a uvedenie
do prevádzky . . . . . . . . . . . . . . . . . . . . . .117
Couvací kamera
Návod k montáži a obsluze . . . . . . . . . . 125
Tol a tók a m e ra
Szerelési és használati útmutató . . . . . . 133
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
POWER & CONTROL
CAMERAS
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 1 Tuesday, March 23, 2021 4:53 PM
© 2021 Dometic Group. The visual appearance of the contents of this manual is protected
by copyright and design law. The underlying technical design and the products contained
herein may be protected by design, patent or be patent pending. The trademarks
mentioned in this manual belong to Dometic Sweden AB. All rights are reserved.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 2 Tuesday, March 23, 2021 4:53 PM
CAM200
3
1 2 3
4
9
6
8
5
7
10 11
12
1
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 3 Tuesday, March 23, 2021 4:53 PM
CAM200
4
2
3
4
5
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 4 Tuesday, March 23, 2021 4:53 PM
CAM200
5
6
7
1
3
4
2
8
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 5 Tuesday, March 23, 2021 4:53 PM
CAM200
6
9
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 6 Tuesday, March 23, 2021 4:53 PM
CAM200
7
0
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 7 Tuesday, March 23, 2021 4:53 PM
CAM200
8
6-8 mm
1.
2.
a
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 8 Tuesday, March 23, 2021 4:53 PM
CAM200
9
1.
2. 3.
Ø 30
4.
b
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 9 Tuesday, March 23, 2021 4:53 PM
CAM200
10
1.
2.
3.
5.
4.
c
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 10 Tuesday, March 23, 2021 4:53 PM
CAM200
11
1.
1.
2.
d
2.
1.
e
f
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 11 Tuesday, March 23, 2021 4:53 PM
CAM200
12
2.
3.
4.
1.
g
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 12 Tuesday, March 23, 2021 4:53 PM
CAM200
EN
13
Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product
manual in order to ensure that you install, use, and maintain the product properly at all times. These instructions
MUST stay with this product.
By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and
that you understand and agree to abide by the terms and conditions as set forth herein. You agree to use this prod-
uct only for the intended purpose and application and in accordance with the instructions, guidelines, and warn-
ings as set forth in this product manual as well as in accordance with all applicable laws and regulations. A failure to
read and follow the instructions and warnings set forth herein may result in an injury to yourself and others, damage
to your product or damage to other property in the vicinity. This product manual, including the instructions, guide-
lines, and warnings, and related documentation, may be subject to changes and updates. For up-to-date product
information, please visit dometic.com.
Contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Information on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Cleaning and caring for the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
11 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
1 Explanation of symbols
!
!
A
WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in
death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in
minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 13 Tuesday, March 23, 2021 4:53 PM
Safety and installation instructions CAM200
EN
14
I
2 Safety and installation instructions
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and incorrect connection voltage
Alterations to the product without express permission from the manufacturer
•Use for purposes other than those described in the operating manual
Please observe the prescribed safety instructions and stipulations from the vehicle
manufacturer and service workshops.
!
WARNING!
Inadequate supply cable connections could result in short circuits, which could have as
a consequence that:
Cable fires occur
The airbag is triggered
Electronic control devices are damaged
Electric functions fail (indicators, brake light, horn, ignition, lights)
A
NOTICE!
To prevent the risk of short circuits, always disconnect the negative terminal of the
vehicle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be discon-
nected.
Please observe the following instructions:
When working on the following cables, only use insulated cable lugs, plugs and flat push-on
receptacles:
30 (direct supply from positive battery terminal)
15 (connected positive terminal, behind the battery)
31 (return line from the battery, earth)
L (indicator lights left)
R (indicator lights right)
Do not use terminal strips.
Use a crimping tool to connect the cables.
When connecting to cable 31 (earth), screw the cable
to the vehicle's earth bolt with a cable lug and a gear disc or
to the sheet-metal bodywork with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
NOTE
Supplementary information for operating the product.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 14 Tuesday, March 23, 2021 4:53 PM
CAM200
EN
15
If you disconnect the negative terminal of the battery, all data stored in the volatile memories will
be lost.
The following data must be set again, depending on the vehicle equipment options:
–Radio code
–Vehicle clock
–Timer
On-board computer
–Seat position
You can find instructions for making these settings in the appropriate operating instructions.
Observe the following installation instructions:
!
CAUTION!
Secure the parts installed in the vehicle in such a way that they cannot become loose
under any circumstances (sudden braking, accidents) and cause injuries to the
occupants of the vehicle.
Secure any parts of the system covered by the bodywork in such a manner that they
cannot be come loose or damage other parts and cables or impair vehicle functions
(steering, pedals, etc).
Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may only be
performed by qualified specialists.
A
NOTICE!
To prevent damage when drilling, make sure there is sufficient space on the other
side for the drill head to come out.
Deburr all drill holes and treat them with a rust-protection agent.
Observe the following instructions when working with electrical parts:
A
NOTICE!
When testing the voltage in electrical cables, only use a diode test lamp or a
voltmeter.
Test lamps with an illuminant take up voltages which are too high and which can
damage the vehicle's electronic system.
When making electrical connections, ensure that:
they are not kinked or twisted
they do not rub on edges
they are not laid in sharp edged ducts without protection.
Insulate all connections.
Secure the cables against mechanical wear with cable binders or insulating tape,
for example to existing cables.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 15 Tuesday, March 23, 2021 4:53 PM
Scope of delivery CAM200
EN
16
The camera is watertight. However, the sealings on the camera cannot withstand a high-pres-
sure cleaner (fig. 4, page 4).
Observe also the following instructions:
Do not open the camera, as this impairs the sealing and the function of the camera (fig. 5,
page 4).
Do not pull at the cables, as this impairs the sealing and the function of the camera (fig. 6,
page 5).
The camera is not suitable for submerged operation (fig. 7, page 5).
3Scope of delivery
4Intended use
The camera CAM200 is a rear view video camera for use on bike racks.
The camera can be used to observe the space around the vehicle from the driver's seat when
manoeuvring or parking, for example.
!
This product is only suitable for the intended purpose and application in accordance with these
instructions.
This manual provides information that is necessary for proper installation and/or operation of the
product. Poor installation and/or improper operating or maintenance will result in unsatisfactory
performance and a possible failure.
The manufacturer accepts no liability for any injury or damage to the product resulting from:
Incorrect assembly or connection, including excess voltage
No. in
fig. 8,
page 5
Quantity Description Ref. no.
1 1 Camera CAM200 9600049683
2 1 Connector grommet CAB25 9600027073
3 2 Cable clip
4 1 Spiral cable 9600026478
1 Installation and Operating Manual
WARNING!
Risk of injury!
Since rear view systems are designed merely as an additional aid for reversing, it does
not relieve you of the duty to take proper care when reversing.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 16 Tuesday, March 23, 2021 4:53 PM
CAM200
EN
17
Incorrect maintenance or use of spare parts other than original spare parts provided by the man-
ufacturer
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product specifications.
5 Technical description
The camera, which is encased in plastic housing, transmits the image to a monitor via a cable.
The camera is mounted under the profile of the bike rack and provides a free view with a loaded
bike rack.
Two automatically operating camera modules provide the image with the bike rack folded up or
down (fig. 9, page 6).
Three distance lines (green, yellow, and red) are displayed (fig. 0, page 7).
6 Information on the electrical connections
6.1 Laying cables
A
Please observe the following instructions:
As far as possible, use original openings or alternative openings for the connecting cable duct,
e.g. the paneling edges, ventilation grilles or blank panels. If no openings are available, you
must drill holes for the cables. Check beforehand that there is sufficient room for the drill head
to come out on the other side.
Wherever possible lay cables inside the vehicle, as they are better protected inside than outside
the vehicle.
If you do need to lay a cable outside the vehicle, ensure that it is well secured (use additional
cable ties, insulating tape, etc.).
To prevent damage to the cables, when laying them ensure that there is sufficient distance to
hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heater etc.).
Use corrugated piping or other protective materials to protect against mechanical wear.
Screw on the plug connection of the connecting cables to protect against water penetration
(fig. d, page 11).
NOTICE! Risk of damage!
To prevent damage, when drilling ensure that there is sufficient space on the other
side for the drill head to come out.
Cables and connections which are not properly installed will cause malfunctions or
damage to components. Correct installation of cables and connections is the basic
prerequisite for lasting and trouble-free operation of the retrofitted components.
The cables may not be exposed for long periods to solvents such as benzine, as the
solvents can damage the cable.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 17 Tuesday, March 23, 2021 4:53 PM
Mounting the camera CAM200
EN
18
When laying electric connections, ensure that
They are not kinked or twisted
They do not rub on edges
They are not laid in sharp edged ducts without protection (fig. 3, page 4)
Attach the cables securely in the vehicles to prevent tripping hazards. Use cable binders, insu-
lating tape or glue the cables in place.
Protect every through-hole made in the bodywork against water penetration, e.g. by using a
cable with a sealant and by spraying the cable and the cable sleeve with sealant.
I
7 Mounting the camera
7.1 Tools required
For installation and assembly you will require the following tools:
Drill bit set (fig. 1 1, page 3)
Drill (fig. 1 2, page 3)
Screwdriver (fig. 1 3, page 3)
Set of ring or open-ended spanners (fig. 1 4, page 3)
Measuring ruler (fig. 1 5, page 3)
Hammer (fig. 1 6, page 3)
Centre punch (fig. 1 7, page 3)
To make and test the electrical connection, the following tools are required:
Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)
Crimping tool (fig. 1 10, page 3)
Insulating tape (fig. 1 11, page 3)
Cable bushing sleeves, if necessary
To fasten the cables you may require additional cable binders.
7.2 Mounting and connecting the camera
Proceed as shown (fig. a, page 8 to fig. f, page 11).
A
NOTE
Do not start sealing the through-holes until all installation work has been finished for the
camera, and the required cable lengths have been established.
NOTICE! Risk of damage!
Ensure that there is sufficient space on the other side for the drill head to come out
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 18 Tuesday, March 23, 2021 4:53 PM
CAM200
EN
19
I
Aligning the camera
Use the monitor image to align the camera (fig. g, page 12).
Use the monitor image to check the function of the camera.
8 Cleaning and caring for the camera
A
Clean the camera with a soft, damp cloth from time to time.
9Warranty
The statutory warranty period applies. If the product is defective, please contact your retailer or the
manufacturer's branch in your country (see dometic.com/dealer).
For repair and warranty processing, please include the following documents when you send in the
product:
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
10 Disposal
Place the packaging material in the appropriate recycling waste bins, wherever possible.
M
If you wish to finally dispose of the product, ask your local recycling center or specialist
dealer for details about how to do this in accordance with the applicable disposal
regulations.
NOTE
To minimise corrosion in the plug, apply a small amount of grease – such as pin grease
– inside the plug.
NOTICE! Risk of damage!
Do not use sharp or hard objects to clean the device as these may damage the device.
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 19 Tuesday, March 23, 2021 4:53 PM
Technical data CAM200
EN
20
11 Technical data
Approval
The device has the E24 approval.
PerfectView CAM200
Ref. no: 9600049683
Image sensor: 1/4" CMOS
Pixels: approx. 307000 pixels
Video standard: NTSC
Light sensitivity: 0,1 Lux
Operating voltage: 10 – 16 Vg
Power consumption: 1 W
Protection class: IP69
Operating temperature: –30 °C to 70 °C
Dimensions W x H x D: 165 x 35 x 42 mm
Weight: 250 g
24
DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 20 Tuesday, March 23, 2021 4:53 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144

Dometic CAM200 Käyttö ohjeet

Tyyppi
Käyttö ohjeet