Kenwood FPM810 MULTI PRO SENSE Omistajan opas

Kategoria
Food processors
Tyyppi
Omistajan opas

Tämä käsikirja sopii myös

instructions
istruzioni
instrucciones
Bedienungsanleitungen
gebruiksaanwijzing
FPM810 series
English 3 - 11
Nederlands 12 - 22
Français 23 - 33
Deutsch 34 - 44
Italiano 45 - 55
Dansk 56 - 63
Svenska 64 - 72
Norsk 73 - 81
Suomi 82 - 90
bq
cm
cr
ct
dl
dk
cs
dm
dn
do
cn
co
cp
cq
br
bs
bt
ck
cl
6
5
3
2
4
6
1
5
4
3
2
1
bl
bk
bp
8
7
bo
9
bn bm
9
bn
bk
bl
bm
bq
bp
ck
br
78
bs
bt
cm
+
cn cr dl
co
+
cp
cq dm
do
dn
bo
b
efore using your Kenwood appliance
Read these instructions carefully and retain for future
reference.
R
emove all packaging and any labels.
safety
The blades and discs are very sharp, handle with care.
A
lways hold by the finger grip at the top, away
f
rom the cutting edge, both when handling and
cleaning.
Do not lift or carry the processor by the handle - or the
h
andle may break resulting in injury.
Always remove the knife blade before pouring contents from
the bowl.
K
eep hands and utensils out of the processor bowl and
blender goblet whilst connected to the power supply.
Switch off and unplug:-
before fitting or removing parts;
when not in use;
before cleaning.
Never use your fingers to push food down the feed tube.
Always use the pusher/s supplied.
Never fit the blade unit to the power unit without
the blender goblet fitted.
Before removing the lid from the bowl or blender from the
power unit:-
switch off;
wait until the attachment/blades have completely
stopped;
be careful not to unscrew the blender goblet from the
blade assembly.
SCALD RISK: Hot ingredients should be allowed to cool to
room temperature before blending.
Do not use the lid to operate the processor, always use the
on/off speed control.
This appliance will be damaged and may cause
injury if the interlock mechanism is subjected to
excessive force.
Always unplug your food processor when not in
use.
Never use an unauthorised attachment.
Never leave the appliance unattended when it is operating.
Never use a damaged appliance. Get it checked or repaired:
see ‘service & customer care’.
Never let the power unit, cord or plug get wet.
Don’t let excess cord hang over the edge of a table or
worktop or touch hot surfaces.
Do not exceed the maximum capacities stated in the
recommended speed chart.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Only use the appliance for its intended domestic use.
Kenwood will not accept any liability if the appliance is
subject to improper use, or failure to comply with these
instructions.
Misuse of your processor/blender can result in injury.
T
he maximum rating is based on the attachment that draws
the greatest load. Other attachments may draw less power.
Refer to the relevant section under “using the attachments”
for additional safety warnings for each individual attachment.
b
efore plugging in
M
ake sure your electricity supply is the same as the one
shown on the underside of your appliance.
T
his appliance conforms to EC directive 2004/108/EC on
E
lectromagnetic Compatibility and EC regulation no.
1935/2004 of 27/10/2004 on materials intended for contact
with food.
b
efore using for the first time
1
Remove the plastic blade covers from the knife blade. Take
care the blades are very sharp. These covers should
b
e discarded as they are to protect the blade during
m
anufacture and transit only.
2 Wash the parts see ‘care & cleaning’
key
processor
1
power unit
2
Trïtan™ bowl with drive shaft
3
detachable drive shaft
4
Trïtan™ lid
5
feed tube
6
pushers
7
safety interlocks
8
cord storage (at back)
9
auto button
bk
speed/pulse control
bl
power on light
weighing function
bm
kg/lb button
bn
display screen
bo
on/zero button
bp
weighing tray
thermoresist blender
bq
filler cap
br
lid
bs
goblet
bt
sealing ring
ck
blade unit
cl
filler cap vents
attachments
cm
knife blade
cn
dough tool
co
dual whisk
cp
folding tool
cq
max capacity disc
cr
4mm slicing/grating disc
cs
2mm slicing/grating disc
ct
extra fine grater disc
dk
fine Julienne disc
dl
decorative slicing disc
dm
mini bowl and blade
dn
citrus juicer
do
attachment storage box
3
to use your food processor
1 Fit the bowl to the power unit. Place the handle towards the
back on the right hand side and turn clockwise
1
until it
l
ocks.
2 Fit an attachment over the bowl drive shaft.
Note: Detachable drive shaft
2
should be fitted
w
hen using the discs, mini bowl, whisk, folding
tool and citrus juicer.
Always fit the bowl and attachment onto the processor
b
efore adding ingredients.
3 Fit the lid
3
- ensuring the top of the drive shaft/tool locates
into the centre of the lid.
T
he processor will not operate if the bowl or lid
are not fitted correctly into the interlock. Check
that the feed tube and bowl handle are situated
t
o the right hand side.
4 Plug in. The Power On light will come on and flash until the
bowl and lid are fitted correctly. Select one of the following
options: -
Auto Button the light will come on when the Auto Button is
pressed and the optimum speed for the attachment will be
automatically selected.
Speed Control – manually select the required speed (refer to
the recommended speed chart).
Pulse – use the pulse (P) for short bursts. The pulse will
operate for as long as the control is held in position.
5 At the end of processing turn the speed control to the ‘O’ off
position or if using the Auto press the button and the light
will go out.
The Power On light will flash if either the lid or
bowl are not fitted or incorrectly fitted.
The Auto Button will not operate if a speed is
selected on the speed control.
Always switch off and unplug before removing the
lid.
important
Your processor is not suitable for crushing or grinding coffee
beans, or converting granulated sugar to caster sugar.
Eco function
If the food processor is left plugged in for over 30 minutes
without being used, it will go into standby mode to reduce
energy consumption.
The Power On light will pulse slowly and the food processor
will not operate until one of the following actions are carried
out:-
The Auto Button is pressed.
The speed control is turned to a speed and then turned
back to the ‘O’ off position.
The light will change to being constantly lit when ready to
use.
Note: If the bowl or lid are not engaged into the interlock the
power on light with pulse more rapidly than the Eco function.
weighing function
Your food processor is fitted with a built in weighing function
t
o allow ingredients to be weighed straight into the bowl or
b
lender goblet.
The Maximum weighing capacity is 3Kg. This is the total
w
eight of all the ingredients including the weight of the bowl
o
r goblet.
to use the weighing function
1 Always fit the bowl, detachable drive shaft and attachment
o
r blender goblet onto the power unit before adding
ingredients.
2 Plug in the display screen will
r
emain blank.
3 Press the ON/ZERO button once
and the display screen will light up.
4 Press the (kg/lb) button to select
either grams or ounces. The
display will default to kg/g when
first switched on.
The unit weighs in 2g increments
and teaspoon/tablespoon
measures are recommended for
weighing small quantities.
5 Check the display shows ‘O’, if
not, zero by pressing the ON/ZERO button. Then weigh the
required ingredients straight into the bowl or goblet. After the
weight is displayed, press the ON/ZERO button and the
display will return to ‘O’. Add the next ingredients and that
weight will be displayed. Repeat until all ingredients are
weighed.
If the display is not zeroed and either the ingredients or the
bowl/attachment/lid are removed the display will show [ - - -
-] to represent a minus reading.
To zero press the ON/ZERO button once.
6 Add the lid and select a speed to operate the processor.
During operation the display screen will freeze [- - - -] until
the speed control returned to the ‘O’ off position.
After processing the last weight will be displayed on the
screen when the speed control is returned to the ‘O’ off
position. Note: The weight of the lid will be included if the
display is not zeroed before switching on.
The weight of any additional ingredients added down the
feed tube whilst the processor is running will not be shown
on the display screen.
4
bp
weighing tray
A
removable weighing tray is
s
upplied for weighing
ingredients without the bowl or
blender.
T
o use, place the tray on top of
t
he power unit. Then follow
steps 2 to 5 under ‘to use the
weighing function’.
T
o remove, just lift the tray off.
auto switch off
T
he display screen will turn off automatically if the same
weight reading is shown after 5 minutes.
The display screen can be turned off manually by pressing
and holding down the ON/ZERO button for a few seconds.
i
mportant
Do not overload by exceeding the maximum weighing
capacity of 3Kg. The display will show [0 – Ld] if the
weighing function is overloaded.
Do not subject the power unit to excessive force as this may
damage the weighing sensor.
Always place the processor on a dry flat surface prior to
weighing.
Do not move the power unit during operation of the
weighing function.
to use your thermoresist blender
1 Fit the sealing ring
bt
into the blade unit
ck
- ensuring the
seal is located correctly in the grooved area.
Leaking will occur if the seal is damaged or
incorrectly fitted.
2 Hold the underside of the blade unit
ck
and insert the
blades into the goblet - turn anti-clockwise until it clicks
4
.
Refer to the graphics on the underside of the blade unit as
follows:
- unlocked position
- locked position
The blender will not work if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure
5
. Fit the
filler cap.
5 Place the blender onto the power unit, and turn clockwise
6
to lock.
The appliance will not operate if the blender is
incorrectly fitted to the interlock.
6 Select Auto, or a speed (refer to the recommended speed
chart) or use the pulse control.
safety
SCALD RISK: Hot ingredients should be allowed to cool to
room temperature before blending.
Always take care when handling the blade assembly and
avoid touching the cutting edge of the blades when
cleaning.
Only operate the blender with the lid in place.
Only use the goblet with the blade assembly supplied.
Never run the blender empty.
To ensure the long life of your blender, do not run it for
longer than 60 seconds.
S
moothie recipes - never blend frozen ingredients that have
formed a solid mass during freezing, break it up before
adding to the goblet.
I
mportant - The skirt on the base of the goblet is fitted
during manufacture and no attempt should be made to
remove it.
hints
When making mayonnaise, put all the ingredients, except
the oil, into the blender. Remove the filler cap. Then, with the
appliance running, add the oil slowly through the hole in the
lid.
Thick mixtures, e.g. pâtés and dips, may need scraping
down. If the mixture is difficult to process, add more liquid.
Ice crushing - operate the pulse in short bursts until crushed to
the desired consistency.
The processing of spices is not recommended as they may
damage the plastic parts.
The appliance will not work if the blender is incorrectly fitted.
To blend dry ingredients - cut into pieces, remove the filler
cap, then with the appliance running, drop the pieces down
one by one. Keep your hand over the opening. For best
results empty regularly.
Don’t use the blender as a storage container. Keep it empty
before and after use.
Never blend more than 1.6 litres (2 pts 8 fl oz) - less for
frothy liquids like milkshakes.
5
IMPORTANT: HOT
BLENDING
INSTRUCTIONS
To minimise the possibility of scalding when blending hot
i
ngredients keep hands and other exposed skin away from
t
he lid to prevent possible burns. The following precautions
must be observed:
C
AUTION: Blending very hot ingredients may
result in hot liquid and steam being forced
suddenly past the lid or filler cap
bq
.
We recommend that hot ingredients are
allowed to cool before blending.
NEVER exceed 1200mls/5 cups capacity if processing
hot liquids, such as soups (refer to the markings on the
goblet).
ALWAYS commence blending at a low speed and
gradually increase the speed. NEVER blend hot liquids
by using the Pulse setting.
Liquids which tend to foam such as milk, should be
limited to a maximum capacity of 1000mls/4 cups.
Take care when handling the blender as the goblet and
its contents will be very hot.
Take particular care when removing the lid. The lid is
designed to be a tight fit to prevent leakage. If necessary
protect your hands with a cloth or oven gloves when
handling.
Ensure the goblet is securely attached to the base and
when removing from the appliance, guide the base and
ensure it is removed together with the goblet.
Ensure that the lid and filler cap are securely in place
before every blending operation.
Always ensure that the vents in the filler cap are clear
before every blending operation
cl
.
When fitting the lid to the goblet always ensure that the
lid and goblet rim are clean and dry to ensure a good
seal and prevent spillage.
recommended speed chart
tool/attachment function recommended processing maximum
s
peed time
c
apacities
K
nife blade All in one cake mixes 8 15-20 secs 1.7Kg/3lb 7oz
f
lour weight
P
astry - rubbing fat into flour 5 –8 10 secs 500g/1lb 2oz
flour weight
A
dding water to combine pastry ingredients 10-20 secs
C
hopping fish and lean meat Pulse –8 10-30 secs 800g/1lb 8oz
P
âtés and terrines max lean beef
Chopping vegetables Pulse 5-10 secs 500g/1lb 2oz
Chopping nuts 8 30-60 secs 200g/8oz
Pureeing soft fruit, cooked fruit and vegetables 8 10-30 secs 1Kg/2lb 4oz
Sauces, dressing and dips 8 2 mins max 800g/1lb 8oz
Knife blade with Cold soups Start at low 30-60 secs 1.7 litres/3pts
m
ax capacity disc speed and
Milkshakes/batters increase to 15-30 secs 1.3 litres/2pts
maximum
Dual whisk Egg whites 8 60-90 secs 4 (150g)
Egg & sugar for fatless sponges 8 4-5 min 3 eggs (150g)
Cream 8 30 secs 500 ml/18 fl oz
Creaming fat and sugar 8 2 mins max 200g/8oz fat
200g/8oz sugar
Dough tool Yeasted mixes 8 60 secs 1Kg/ 2lb 4oz total wt
White Bread Flour 8 60 secs 600g/1lb 6oz flour wt
Wholemeal Bread Flour 8 60 secs 500g/1lb 2oz flour wt
Folding tool Whipping cream and fruit purees Auto 30 secs 300g/12oz cream,
300g/12oz puree
Egg whites into heavy mixtures Auto 30 secs total weight 600g/1lb 6oz
Discs - slicing/grating Firm food items such as carrots, hard cheeses 5 –8
Softer items such as cucumbers, tomatoes 1 –5
Extra fine grater Parmesan cheese, potatoes for German 8–
potato dumplings
Decorative slicing disc Firm food items such as carrots and potatoes 5 –8
Softer food items such as cucumber
Fine Julienne disc Potato straws and rosti 8–
Stir fries and vegetable garnishes
Thermoresist blender Cold liquids and drinks 8 15-30 secs 1.6 litres/2 pt 8 fl oz
Stock based soups 8 30 secs 1.2 litres/2 pt 1 fl oz
Soups using milk 8 30 secs 1 litres/1pt 8 fl oz
We recommend that hot ingredients are allowed to cool before blending. However should you wish to process
hot ingredients please read the Hot Blending Safety instructions.
Mini bowl and knife Meat 8 20 secs + Pulse 300g/12oz Lean beef
Chopping herbs 8 30 secs 20g/1oz
Chopping nuts 8 30 secs 100g/4oz
Mayonnaise 8 30 secs 2 Eggs
300g/12oz Oil
Purees 8 30 secs 200g/8oz
Mini bowl with discs See individual discs recommended speed 500g/1lb 2oz Max
Do not overfill bowl
Citrus Juicer Smaller items i.e. limes and lemons 1 –2 2Kg/4lb 8oz
Larger fruits i.e. oranges and grapefruits
6
This is for guidance only and will vary depending on the exact recipe and ingredients being processed.
Do not fill above
the maximum capacity
marked on the bowl
using the attachments
R
efer to recommended speed chart for each attachment.
cm
knife blade
The knife blade is the most versatile of all the attachments.
T
he length of the processing time will determine the texture
achieved. For coarser textures use the pulse control.
Use the knife blade for cake and pastry making, chopping
r
aw and cooked meat, vegetables, nuts, pâté, dips,
pureeing soups and to also make crumbs from biscuits and
bread.
h
ints
C
ut food such as meat, bread, vegetables into cubes
approximately 2cm/3/4in before processing.
B
iscuits should be broken into pieces and added down the
feed tube whilst the appliance is running.
When making pastry use fat straight from the fridge cut into
2cm/3/4in.cubes.
Take care not to over-process.
cn
dough tool
Use for yeasted dough mixes.
Place the dry ingredients in the bowl and add the liquid
down the feed tube whilst the appliance is running. Process
until a smooth elastic ball of dough is formed this will take
approx. 60 secs.
Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become
unstable.
co
dual whisk
Use for light mixtures such as egg whites, cream,
evaporated milk and for whisking eggs and sugar for fatless
sponges.
using the whisk
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Push each beater
7
securely into the drive head.
3 Fit the whisk by carefully turning until it drops over the drive
shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft locates into the
centre of the lid.
6 Switch on.
important
The whisk is not suitable for making all in one
cake mixes as these mixes are too heavy and will
damage it. Always use the knife blade.
hints
Best results are obtained when the eggs are at room
temperature.
Ensure the bowl and whisks are clean and free from grease
before whisking.
c
reaming fat and sugar
For best results fat should be allowed to soften at room
temperature (20°C) before creaming. DO NOT use fat
s
traight from the fridge as this will damage the
whisk.
Heavier ingredients such as flour and dried fruit should be
f
olded in by hand.
Do not exceed the maximum capacity or processing time
stated in the recommended speed chart.
cp
folding tool
U
se the folding tool to fold light ingredients into heavier
mixtures for meringues, mousses and fruit fools.
1 Fit the bowl onto the power unit, add the detachable drive
s
haft.
2
Push each paddle
8
s
ecurely into the drive head.
3 Fit the folding tool by carefully turning until it drops over the
drive shaft.
4 Add the ingredients.
5 Fit the lid ensuring the end of the shaft locates into the
centre of the lid .
6 Select Auto.
hints
For best results do not over whisk egg whites or cream –
the folding tool will not be able to fold the mixture correctly if
the whisked mix is too firm.
Do not fold the mixture for longer than stated in the
recommended speed chart as the air will be knocked out
and the mix will be too loose.
Any unmixed ingredients left on the paddle or sides of the
bowl should be carefully folded in using the spatula.
cq
max capacity disc
When blending liquids in the bowl, the max capacity disc
must be used with the knife blade. It prevents leaking and
improves the chopping performance of the blade.
1 Fit the bowl onto the power unit.
2 Fit the knife blade.
3 Add ingredients to be processed.
4 Fit the capacity disc over the top of the blade ensuring it sits
on the ledge inside the bowl
9
. Do not push down on
the capacity disc.
5 Fit the lid and switch on.
slicing/grating discs
reversible slicing/grating discs - 4mm
cr
, 2mm
cs
Use the grating side for cheese, carrots, potatoes and foods
of a similar texture.
Use the slicing side for cheese, carrots, potatoes, cabbage,
cucumber, courgette, beetroot and onions.
extra fine grater disc
ct
Grates Parmesan cheese and potatoes for German potato
dumplings.
fine julienne
dk
Use to cut potatoes into straws and coarse grate for rosti,
stir fries and vegetable garnishes.
decorative slicing disc
dl
Use to slice potatoes, carrot, cucumbers and foods of a
similar texture into fluted shaped slices.
7
safety
N
ever remove the lid until the cutting disc has
completely stopped.
H
andle the cutting discs with care - they are
e
xtremely sharp.
Do not overfill the bowl do not exceed the
m
aximum capacity level marked on the bowl.
to use the cutting discs
1
Fit the bowl onto the power unit, add the detachable drive
shaft
2
.
2 Holding by the centre grip, place the disc onto the drive shaft
w
ith the appropriate side uppermost
bk
.
3 Fit the lid.
4 Put the food in the feed tube.
Choose which size feed tube you want to use. The pusher
contains a smaller feed tube for processing individual items
or thin ingredients.
To use the small feed tube - first put the large pusher inside
the feed tube.
To use the large feed tube - use both pushers together.
5 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube.
hints
Use fresh ingredients
Don’t cut food too small. Fill the width of the feed tube fairly
full. This prevents the food from slipping sideways during
processing. Alternatively use the small feed tube.
When using the Julienne disc, place ingredients horizontally.
When slicing or grating: food placed upright
bl
comes out
shorter than food placed horizontally
bm
.
Food placed upright comes out shorter than food placed
horizontal.
There will always be a small amount of waste on the disc or
in the bowl after processing.
dm
mini bowl and knife
Use the mini processor bowl to chop herbs and process
small quantities of ingredients e.g. meat, onion, nuts,
mayonnaise, vegetables, purées, sauces and baby food.
The slicing/grating discs can also be used with the mini
bowl.
Insert the mini bowl without the knife blade fitted and refer to
the slicing/grating disc section for fitting and usage
instructions.
Do not overfill the bowl.
mini blade
mini bowl
to use the mini bowl and knife
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Fit the mini bowl over the detachable drive shaft - ensure the
cut out sections align with the locating tabs
bn
on the main
bowl.
Note: The main bowl lid cannot be fitted if the mini bowl is
not located correctly.
3 Place the knife blade over the drive shaft
bo
.
4
Add the ingredients to be processed.
5
Fit the lid and switch on.
s
afety
Never remove the lid until the knife blade has completely
s
topped.
T
he knife blade is very sharp - always handle with care.
important
Do not process spices they may damage the plastic.
D
o not process hard food such as coffee beans, ice cubes
or chocolate they may damage the blade.
hints
H
erbs are best chopped when clean and dry.
Always add a little liquid when blending cooked ingredients
t
o make baby food.
Cut foods such as meat, bread, vegetables into cubes
approximately 1-2 cm (
1
2
3
4 in) before processing.
When making mayonnaise add the oil down the feed tube.
dn
citrus juicer
Use the citrus juicer to squeeze the juice from citrus fruits
(eg oranges, lemons, limes and grapefruits).
cone
sieve
to use the citrus juicer
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle
bp
.
3 Place the cone over the drive shaft turning until it drops all
the way down
bq
.
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
The citrus juicer will not operate if the sieve is
not locked correctly.
For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
To help with juice extraction move the fruit from side to side
when juicing.
When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
do
attachment storage box
Your food processor is supplied with a storage box for your
bowl attachments and discs.
1 Fit the knife blade and discs into the storage box when not
in use
br
.
2 The storage box is fitted with a safety lock - close the lid to
lock. To open, push the tab in
bs
and lift up the lid
bt
.
8
care & cleaning
A
lways switch off and unplug before cleaning.
Handle the blades and cutting discs with care -
t
hey are extremely sharp.
S
ome foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour of
y
our food. Rub with a cloth dipped in vegetable oil to
r
emove the discolouration.
p
ower unit
Wipe with a damp cloth, then dry. Ensure that the interlock
a
rea is clear of food debris.
D
on’t immerse the power unit in water.
Store excess cord in the storage area at the back of the
p
ower
u
nit
ck
.
blender
1 Empty the goblet, unscrew the blade unit by turning to the
unlock position to release.
2 Wash the goblet by hand.
3 Remove and wash the seals.
4 Don’t touch the sharp blades brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
dual whisk/folding tool
Detach the beaters/paddles from the drive head by gently
pulling them free. Wash in warm soapy water.
Wipe the drive head with a damp cloth, then dry. Do not
immerse the drive head in water.
all other parts
Wash by hand, then dry.
Alternatively they are dishwasher safe and can be washed
on the top rack of your dishwasher. Avoid placing items on
the bottom rack directly over the heating element. A short
low temperature (Maximum 50°C) programme is
recommended.
service & customer care
I
f the cord is damaged it must, for safety reasons, be
replaced by KENWOOD or an authorised KENWOOD
r
epairer.
I
f you experience any problems with the
o
peration of the processor, before calling for
assistance refer to the troubleshooting guide.
If you need help with:
u
sing your appliance or
servicing or repairs
Contact the shop where you purchased your appliance.
Designed and engineered by Kenwood in the UK.
Made in China.
IMPORTANT INFORMATION FOR CORRECT
DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed
of as urban waste.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in energy
and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a
crossed-out wheeled dustbin.
9
item suitable for
dishwashing
main bowl, mini bowl, lid, pusher
knife blades, dough tool
detachable drive shaft
discs
max capacity disc
whisk beaters/folding tool paddles
Do not immerse the drive head in water
blender goblet, lid, filler cap
blade unit and seal for blender
citrus juicer
spatula
10
troubleshooting guide
P
roblem Cause Solution
The processor will not operate. No Power. Check processor is plugged in.
N
o power/indicator light not lit.
B
owl not fitted to power unit correctly. Check bowl is located correctly
and the handle is situated
t
owards the right hand side.
B
owl lid not locked on correctly. Check that the lid interlock is
located correctly into the
handle area.
T
he processor will not
w
ork if the bowl and lid
a
re fitted incorrectly.
Eco function operating. Press either the Auto Button or
t
urn speed control on, then
return to ‘O’ to switch off Eco
function.
If none of the above check the
fuse/circuit breaker in your home.
Blender will not operate. Blender not locked on correctly. The blender will not operate if
fitted incorrectly to the
interlock.
Blender not assembled correctly. Check blade unit is fully
tightened into the goblet.
Processor stops or slows Overload protection operated. Switch off, unplug and allow
during processing. Processor overloaded or overheated during the appliance to cool down for
operation. approximately 15 minutes.
Maximum capacity exceeded. Refer to the speed chart for
maximum capacities to
process.
Weighing function
Display screen freezes on [- - - -]. Quantity weighed too small. Use teaspoon and tablespoon
measures for very small
quantities.
Weight changed on display screen. Power unit moved during operation. Do not move unit during use.
Zero the display before
weighing next ingredients.
Power On light flashing rapidly. Normal operation. Check interlocks are engaged
The light will flash if the bowl, lid or blender are correctly.
not fitted to the power unit or not locked in
place correctly.
Power On light flashing slowly. Normal operation.
Food processor left plugged in for over 30 minutes Press either the Auto Button or
without being operated and gone into Eco mode. turn speed control on and then
return to ‘O’ to switch off Eco
function.
Auto and Power On light flashing. Normal operation. Check interlocks are engaged
The light will flash if the Auto selected but correctly or press the Auto
interlocks not engaged. button to switch off the Auto
function.
Blender leaking from blade assembly base. Seal missing. Check seal is fitted correctly
Seal incorrectly fitted. and not damaged. To obtain a
Seal damaged. replacement seal see “service &
customer care”.
11
troubleshooting guide
P
roblem Cause Solution
Blender seal missing from blade unit when The seal is packed pre-fitted to the blade unit. Unscrew goblet and check that
r
emoved from packaging. seal is fitted to blade unit.
To obtain a replacement seal
see “service & customer care”.
Poor performance of tools/attachments. Refer to hints in relevant “using the attachment” section. Check attachments are
a
ssembled correctly.
v
oordat u uw Kenwood-apparaat gebruikt:
Lees deze instructies zorgvuldig door en bewaar ze voor
toekomstig gebruik.
V
erwijder alle verpakking en labels.
veiligheid
D
e messen en de schijven zijn erg scherp; ga er dus
voorzichtig mee om. Houd ze bij het hanteren en
s
choonmaken altijd bovenaan bij de vingergreep
e
n weg van het snijvlak, vast.
Til de keukenmachine niet bij het handvat op en draag hem
e
venmin op die manier; hierdoor kan het handvat afbreken,
w
aardoor u letsel kunt oplopen.
Voordat u de inhoud uit de kom giet, dient u altijd eerst het
m
es te verwijderen.
H
oud uw handen en keukengereedschap uit de kom van de
keukenmachine en de beker van de blender, wanneer deze
op het lichtnet is aangesloten.
Schakel het apparaat uit en haal de stekker uit het
stopcontact:-
voordat u onderdelen aanbrengt of verwijdert;
als u het apparaat niet gebruikt;
voor het reinigen.
Gebruik nooit uw vingers om voedsel in de invoerkoker te
duwen. Gebruik altijd de bijgeleverde stamper.
Zet het mes nooit op het motorblok zonder dat de
beker van de blender is bevestigd.
Doe het volgende, voordat u het deksel van de kom of de
blender van het motorblok verwijdert:-
zet het apparaat uit;
wacht totdat de hulpstukken / messen helemaal tot
stilstand zijn gekomen;
zorg dat u de blenderbeker niet losschroeft van de
messeneenheid.
VERBRANDINGSGEVAAR: Laat hete ingrediënten eerst
tot kamertemperatuur afkoelen voordat u ze in de blender
verwerkt.
Gebruik nooit het deksel om de keukenmachine te bedienen,
maar altijd de aan/uit-knop.
Als teveel kracht wordt uitgeoefend op het
vergrendelingsmechanisme, wordt dit apparaat
beschadigd en kan het letsel veroorzaken.
Haal de stekker altijd uit de keukenmachine
wanneer u hem niet gebruikt.
Gebruik nooit een niet bij het apparaat behorend hulpstuk.
Laat het apparaat nooit onbeheerd terwijl het aan staat.
Gebruik nooit een beschadigd apparaat. Laat het nakijken of
repareren: zie Onderhoud en klantenservice.
Laat het motorhuis, het netsnoer of de stekker nooit nat
worden.
Laat het snoer nooit over de rand van een tafel of werkblad
hangen of in aanraking komen met hete oppervlakken.
U mag de maximum capaciteit die in de snelheidstabel
wordt aangegeven, niet overschrijden.
Dit apparaat is niet bedoeld voor gebruik door personen
(inclusief kinderen) met verminderde lichamelijke, zintuiglijke
of geestelijke vermogens of gebrek aan ervaring en kennis,
tenzij ze toezicht of instructies over het gebruik van het
apparaat hebben gekregen van de persoon die
verantwoordelijk is voor hun veiligheid.
Op kinderen moet toezicht gehouden worden om er zeker
van te zijn dat ze niet met het apparaat spelen.
G
ebruik het apparaat alleen voor het huishoudelijke gebruik
waarvoor het is bedoeld. Kenwood kan niet aansprakelijk
worden gesteld in het geval dat het apparaat niet correct is
g
ebruikt, of waar deze instructies niet worden opgevolgd.
Misbruik van uw keukenmachine/blender kan tot letsel
leiden.
H
et maximum vermogen is afhankelijk van het hulpstuk dat
de grootste hoeveelheid energie verbruikt. Andere
hulpstukken verbruiken misschien minder energie.
Raadpleeg de betreffende paragraaf onder De hulpstukken
g
ebruiken voor aanvullende veiligheidswaarschuwingen voor
ieder hulpstuk afzonderlijk.
voordat u de stekker in het stopcontact steekt
Z
org dat de elektriciteitsvoorziening dezelfde spanning heeft
a
ls op de onderkant van het apparaat wordt aangegeven.
Dit apparaat voldoet aan de EC-richtlijn 2004/108/EC
betreffende de elektromagnetische compatibiliteit en EC-
bepaling 1935/2004 van 27/10/2004 betreffende materialen
die bestemd zijn voor contact met voedsel.
voordat u het apparaat voor het eerst gebruikt
1 Verwijder de plastic beschermhoezen van het mes. Wees
voorzichtig: de messen zijn erg scherp. Deze
beschermhoezen moeten weggegooid worden; ze zijn
uitsluitend bedoeld om het mes tijdens de vervaardiging en
het vervoer te beschermen.
2 Was de onderdelen, zie Reiniging en onderhoud.
legenda
keukenmachine
1
motorblok
2
Trïtan™-kom met aandrijfas
3
verwijderbare aandrijfas
4
Trïtan™-deksel
5
vulopening
6
duwstaafjes
7
veiligheidsvergrendeling
8
snoeropslag (aan achterzijde)
9
auto-toets
bk
snelheids- en pulseerknop
bl
aan/uit-lampje
weegfunctie
bm
kg/lb-knop
bn
weergavevenster
bo
aan/nulknop
bp
weegplaat
thermoresist-blender
bq
vuldop
br
deksel
bs
kan
bt
afsluitring
ck
messeneenheid
cl
ventilatiegaten vuldop
12
Nederlands
V
ouw voor het lezen a.u.b. de voorpagina met illustraties uit
hulpstukken
cm
m
eslemmet
cn
deeghulpstuk
co
d
ubbele garde
cp
v
ouwhulpstuk
cq
schijf voor maximale capaciteit
cr
4
mm-snij-/raspschijf
cs
2
mm-snij-/raspschijf
ct
extra fijne raspschijf
dk
fijne julienneschijf
dl
d
ecoratieve snijschijf
dm
minikom met mes
dn
citruspers
do
o
pslagdoos voor hulpstukken
gebruik van uw keukenmachine
1 Zet de kom op het motorblok. Plaats het handvat aan de
rechterkant naar achteren en draai naar rechts
1
tot de
kom vergrendeld is.
2 Plaats een hulpstuk op de aandrijfas van de kom.
NB: De verwijderbare aandrijfas
2
moet op het
apparaat worden gezet wanneer de schijven,
minikom, garde, het vouwhulpstuk en de
citruspers worden gebruikt.
Zet de kom en het hulpstuk altijd op de keukenmachine
voordat u ingrediënten toevoegt.
3 Zet het deksel
3
erop – zorg ervoor dat de bovenkant van
de aandrijfas/het hulpmiddel in het midden van het deksel
past.
De machine functioneert niet als de kom of het
deksel niet goed vergrendeld zijn. Controleer of
de vulopening en de komhendel zich aan de
rechterkant bevinden.
4 Steek de stekker in het stopcontact. Het aan-/uitlampje gaat
branden en knippert tot de kom en het deksel op de juiste
manier zijn geplaatst. Kies één van de volgende opties: -
Auto-toets – het lampje gaat branden als u op de toets Auto
drukt en de optimale snelheid voor het hulpstuk wordt
automatisch geselecteerd.
Snelheidstoets – selecteer handmatig de vereiste snelheid
(raadpleeg de tabel met aanbevolen snelheden).
Pulseren – gebruik de pulseertoets (P) voor korte pulsen. De
puls duurt zolang als de toets wordt ingedrukt.
5 Aan het eind van de verwerking schakelt u de snelheidstoets
naar de ‘O’/uit-stand, of als u Auto gebruikt, drukt u op die
toets en het lampje gaat uit.
Het aan-/uit-lampje knippert als het deksel of de
kom niet of onjuist zijn bevestigd.
De Auto-toets werkt niet als een snelheid is
geselecteerd met de snelheidstoets.
Voor u het deksel verwijdert, dient u het apparaat
altijd uit te schakelen en de stekker uit het
stopcontact te halen.
belangrijk
Deze keukenmachine is niet geschikt voor het verpulveren of
malen van koffiebonen of voor het vermalen van kristalsuiker
tot basterdsuiker.
Eco-functie
A
ls de foodprocessor langer dan 30 minuten op het
elektriciteitsnet is aangesloten zonder te worden gebruikt,
w
ordt automatisch de standby-stand geactiveerd om het
e
nergieverbruik te beperken.
Het aan-/uitlampje knippert langzaam en de foodprocessor
w
erkt pas als een van de volgende handelingen wordt
u
itgevoerd:-
De Auto-toets wordt ingedrukt.
De snelheidsknop wordt op een snelheid ingesteld en
v
ervolgens naar de 'O'/uit-stand gedraaid.
H
et lampje blijft branden wanneer het apparaat klaar voor
gebruik is.
NB: Als de kom of het deksel niet goed zijn vergrendeld,
k
nippert het aan-/uitlampje sneller dan de Eco-functie.
weegfunctie
Uw foodprocessor is uitgerust met een ingebouwde
weegfunctie waarmee ingrediënten rechtstreeks in de schaal
of blenderkan gewogen kunnen worden.
Het maximum weegvermogen is 3 kg. Dit is het totale
gewicht van alle ingrediënten plus het gewicht van de kom
of de kan.
gebruik van de weegfunctie
1 Zet de kom, verwijderbare aandrijfas en het hulpstuk of de
blenderkan op het motorblok voordat u de ingrediënten
toevoegt.
2 Stop de stekker in het stopcontact
– het weergavescherm blijft leeg.
3 Druk eenmaal op de AAN/NUL-
knop en het weergavescherm licht
op.
4 Druk op de (kg/lb)-knop om
grammen of ounces te selecteren.
Het scherm geeft standaard kg/g
weer wanneer het apparaat
ingeschakeld wordt.
Het apparaat weegt in stappen van
2 g en voor het wegen van kleine
hoeveelheden wordt het gebruik
van theelepels/eetlepels aanbevolen.
5 Controleer of ‘O’ wordt weergegeven; zo niet, dan zet u de
weegschaal op nul door op de AAN/NUL-toets (ON/ZERO)
te drukken. Weeg de benodigde ingrediënten rechtstreeks in
de kom of kan. Nadat het gewicht wordt weergegeven,
drukt u op de AAN/NUL-toets (ON/ZERO) en ziet u ‘O’ op
het scherm. Voeg het volgende ingrediënt toe; het gewicht
hiervan wordt nu weergegeven. Herhaal deze stappen tot
alle ingrediënten zijn gewogen.
Als het scherm niet op nul gezet is en de ingrediënten of de
kom/hulpstuk/deksel worden verwijderd, wordt op het
scherm [ - - - -] weergegeven, hetgeen een aanduiding is
van een negatief getal. Om het apparaat op nul te
zetten, drukt u eenmaal op de AAN/NUL-knop.
6 Zet het deksel erop en selecteer een snelheid voor de
processor.
Wanneer het apparaat in werking is, stopt het
weergavescherm [- - - -] tot de snelheidsknop weer in de
uit-stand ‘O’ staat.
13
N
a verwerking wordt het laatste gewicht weergegeven op
het scherm nadat de snelheidsknop weer in de uit-stand ‘O’
gezet is. NB: Het gewicht van het deksel wordt bij het totaal
o
pgeteld als het scherm niet op nul gezet is voordat het
apparaat werd aangezet.
Het gewicht van ingrediënten die via de vulopening
t
oegevoegd worden, terwijl het apparaat aan staat, wordt
niet op het scherm weergegeven.
bp
weegplaat
E
r wordt een weegplaat
b
ijgeleverd die verwijderd kan
worden en ingrediënten kan
w
egen zonder dat u de kom of
d
e blender gebruikt.
Zet de plaat op het motorblok.
Volg stap 2 tot en met 5 van
paragraaf Gebruik van de
weegfunctie.
Til de plaat van het motorblok
om hem te verwijderen.
automatische uitschakeling
Het scherm schakelt automatisch uit als hetzelfde gewicht
gedurende 5 minuten wordt weergegeven.
Het scherm kan uitgeschakeld worden door de knop
ON/ZERO een paar seconden ingedrukt te houden.
belangrijk
Overbelast de weegschaal niet door het maximumgewicht
van 3 kg te overschrijden. Als de weegfunctie overbelast is,
wordt [0 – Ld] weergegeven.
Oefen geen overmatige druk uit op het motorblok; hierdoor
kan de gewichtsensor beschadigd worden.
Plaats de processor voor het wegen altijd op een droog,
horizontaal oppervlak.
Verplaats het motorblok niet terwijl de weegfunctie gebruikt
wordt.
uw thermoresist-blender gebruiken
1 Zet de afsluitring
bt
in de messeneenheid
ck
– zorg dat de
ring correct in de groef wordt geplaatst.
Het apparaat lekt wanneer de afsluitring
beschadigd is of niet goed is aangebracht.
2 Houd de onderkant van de meseenheid
ck
vast en steek de
messen in de kan – draai ze naar links, totdat ze vastklikken
4
. Raadpleeg de afbeeldingen aan de onderzijde van de
meseenheid, als volgt:
– onvergrendelde stand
– vergrendelde stand
De blender werkt niet als hij incorrect in elkaar is
gezet.
3 Plaats de ingrediënten in de kan.
4 Plaats het deksel op de kan en duw erop om hem goed vast
te zetten
5
. Zet de vuldop erop.
5 Zet de blender op het motorblok en draai hem naar rechts
6
om hem vast te zetten.
Het apparaat werkt niet als de blender onjuist
geplaatst is op de vergrendeling.
6 Selecteer Auto of een snelheid (zie de tabel met aanbevolen
snelheden) of gebruik de pulseerknop.
v
eiligheid
VERBRANDINGSGEVAAR: Laat hete ingrediënten eerst
tot kamertemperatuur afkoelen voordat u ze in de blender
v
erwerkt.
Wees voorzichtig wanneer u de messen hanteert en raak het
snijvlak van de messen bij het reinigen niet aan.
L
aat de blender uitsluitend voorzien van deksel lopen.
Gebruik de kan uitsluitend met de bijgeleverde messen.
De blender nooit leeg gebruiken.
O
m een lange levensduur van uw blender te garanderen,
mag u hem nooit langer dan 60 seconden gebruiken.
Smoothie-recepten – verwerk nooit bevroren ingrediënten
d
ie tijdens de bevriezing tot een vaste massa gevormd zijn;
breek de massa op voor u hem aan de kan toevoegt.
B
elangrijk De rand rond de beker is tijdens de
vervaardiging gemonteerd; probeer niet om deze rand te
verwijderen.
14
BELANGRIJK: INSTRUCTIES
VOOR HET MENGEN VAN HETE
VLOEISTOFFEN
Om de kans op brandwonden te verkleinen bij het
mengen van hete ingrediënten, moet u uw handen en
andere onbeschermde huid uit de buurt van het deksel
houden om eventuele brandwonden te voorkomen.
De volgende voorzorgsmaatregelen moeten worden
getroffen:
VOORZICHTIG: Het mengen van zeer hete
ingrediënten kan tot gevolg hebben dat hete
vloeistof en stoom plotseling uit het deksel of
de vuldop worden gedreven
bq
.
We raden u aan hete ingrediënten te laten
afkoelen voordat ze worden verwerkt.
Overschrijd bij de verwerking van hete vloeistoffen, zoals
soepen, NOOIT de capaciteit van 1200 ml (gebruik de
maatstreepjes op de beker).
Stel de blender in het begin ALTIJD op een lage
snelheid in en verhoog de snelheid geleidelijk. Meng hete
vloeistoffen NOOIT door de pulseerstand te gebruiken.
Vloeistoffen die de neiging hebben om te schuimen,
zoals melk, mogen de maximumcapaciteit van 1000 ml
niet overschrijden.
Wees voorzichtig als u de blender vastpakt: de beker en
de inhoud zijn erg heet.
Wees vooral voorzichtig als u het deksel verwijdert. Om
lekken te voorkomen is het deksel zo ontworpen dat het
precies past. Bescherm bij de hantering zo nodig uw
handen met een doek of ovenwanten.
Zorg dat de beker goed op het onderstel is bevestigd;
wanneer u de beker van het apparaat verwijdert, houdt u
het onderstel vast en zorgt dat hij samen met de beker
wordt verwijderd.
Zorg dat het deksel en de vuldop altijd goed op hun
plaats zitten voordat u de blender inschakelt.
Zorg altijd dat de luchtopeningen in de vuldop vrij zijn
voordat u de blender inschakelt (zie tekening
cl
).
Zorg er bij het plaatsen van het deksel altijd voor dat het
deksel en de rand van de beker schoon en droog zijn,
zodat een goede afsluiting kan worden verkregen en
morsen kan worden voorkomen.
h
andige tips
Bij de bereiding van mayonaise plaatst u alle ingrediënten,
met uitzondering van de olie, in de blender. Verwijder de
v
uldop. Giet de olie vervolgens langzaam door de opening in
het deksel op het draaiende apparaat.
Bij dikke mengsels, zoals patés en dips, moet u de wand
v
an het apparaat misschien schoonschrapen. Als het
mengsel moeilijk verwerkt kan worden, voegt u meer
vloeistof toe.
V
erbrijzelen van ijsblokjes pulseer in korte pulsen tot het ijs
de gewenste consistentie bereikt heeft.
De verwerking van specerijen wordt afgeraden; dit kan de
p
lastic onderdelen beschadigen.
Het apparaat werkt niet als de blender onjuist geplaatst is.
D
roge ingrediënten mengen in stukken snijden, de vuldop
verwijderen, en de stukken één voor één op het draaiende
mes laten vallen. Houd uw handen over de opening. Voor
het beste resultaat het apparaat regelmatig legen.
Gebruik de blender niet om voeding in te bewaren. Zorg dat
deze zowel voor als na gebruik leeg is.
Meng nooit meer dan 1,6 liter - of minder voor schuimende
vloeistoffen zoals milkshakes.
15
16
tabel met aanbevolen snelheden
instrument/hulpstuk functie aanbevelen verwer- maximum
s
nelheid kingstijd
c
apaciteit
M
es Kant-en-klare taartmixen 8 15-20 sec 1,7 kg bloemgewicht
Gebaksdeeg – boter met bloem mengen 5 –8 10 sec 500g bloemgewicht
W
ater toevoegen om ingrediënten te mengen 10-20 sec
Vis en mager vlees hakken Pulse –8 10-30 sec 800g
Patés en terrines max mager rundvlees
Groenten hakken Pulse 5-10 sec 500g
Noten hakken 8 30-60 sec 200g
Z
acht fruit, gekookt fruit en gekookte groenten 8 10-30 sec 1 kg
p
ureren
S
auzen, dressing en dips 8 max 2 min 800g
Mes met schijf voor Koude soepen Begin op lage 30-60 sec 1,7 liter
maximale capaciteit snelheid en
Milkshakes/beslag verhoog 15-30 sec 1,3 liter
tot maximum
Dubbele garde Eiwitten 8 60-90 sec 4 (150g)
Ei en suiker voor vetloze taarten 8 4-5 min 3 eieren (150g)
Room 8 30 sec 500 ml
Boter en suiker kloppen 8 max 2 min 200g vet
200g suiker
Deeghulpstuk Mengsels met gist 8 60 sec 1 kg totaalgewicht
Wit broodmeel 8 60 sec 600g bloemgewicht
Volkoren broodmeel 8 60 sec 500g bloemgewicht
Vouwhulpstuk Slagroom en vruchtenpuree Auto 30 sec 300g room,
300g puree
Eiwitten in zware mengsels vouwen Auto 30 sec totaalgewicht 600g
Schijven – snijden/ Harde ingrediënten als wortelen, harde kaas 5 –8
raspen Zachtere ingrediënten als komkommer, tomaten 1 –5
Extra fijne rasp Parmezaanse kaas, aardappelen voor 8–
Duitse aardappelknoedels
Decoratieve snijschijf Stevige ingrediënten zoals wortelen of 5 –8
aardappelen
Zachtere ingrediënten zoals komkommer
Fijne julienneschijf Aardappellucifers en rösti 8–
Roerbakgerechten en groentegarnituur
Thermoresist-blender Koude vloeistoffen en dranken 8 15-30 sec 1,6 liter
Soep op bouillonbasis 8 30 sec 1,2 liter
Soep met melk 8 30 sec 1 liter
We raden u aan hete ingrediënten te laten afkoelen voordat ze worden verwerkt. Als u hete ingrediënten
toch wilt verwerken, dient u de veiligheidsinstructies voor het mengen van hete ingrediënten te lezen.
Minikom met mes Vlees 8 20 sec + 300g mager rundvlees
pulseren
Kruiden hakken 8 30 sec 20g
Noten hakken 8 30 sec 100g
Mayonaise 8 30 sec 2 eieren
300g olie
Puree 8 30 sec 200g
Minikom met schijven Zie de aanbevolen snelheid voor iedere schijf 500g max
De kom niet te ver
vullen
Citrusfruitpers Kleinere ingrediënten, zoals limoenen en 1 –2 2 kg
citroenen
Groter fruit zoals sinaasappels en grapefruit
Dit dient uitsluitend als richtlijn en is afhankelijk van het precieze recept en de ingrediënten die worden verwerkt.
Niet boven het
op de kom
aangegeven
maximale
vulvermogen
vullen
de hulpstukken gebruiken
R
aadpleeg de aanbevolen snelheidstabel voor elk hulpstuk.
cm
meslemmet
Van alle hulpstukken is het meslemmet het meest veelzijdige.
D
e duur van de verwerkingstijd bepaalt de verkregen textuur.
Voor een grovere textuur gebruikt u de pulseerknop.
Gebruik het meslemmet voor het maken van taart en gebak,
v
oor het fijnhakken van rauw of gekookt vlees, groenten,
noten, paté, dips, voor het pureren van soep en voor het
verkruimelen van koekjes en brood.
t
ips
S
nij etenswaren zoals vlees, brood en groente in blokjes van
2 cm, voordat u ze gaat verwerken.
K
oekjes moeten in stukjes verbrokkeld worden en via de
vulopening worden toegevoegd, terwijl de machine draait.
Als u gebak maakt en de boter rechtstreeks uit de koelkast
gebruikt, moet u de boter in blokjes van 2 cm snijden.
Zorg ervoor dat u de machine niet te lang gebruikt.
cn
deeghulpstuk
Deze haak wordt gebruikt voor het kneden van gegist deeg.
Doe de droge ingrediënten in de kom en giet de vloeistof
door de toevoerbuis, terwijl de vulopening draait. Meng de
ingrediënten totdat een gladde elastische deegbal ontstaat.
Dit duurt 60 seconden.
Kneed het deeg opnieuw met de hand. Kneed het deeg niet
in de kom, omdat de machine hierdoor instabiel kan
worden.
co
dubbele garde
Gebruiken voor lichte mengsels zoals eiwitten, room,
gecondenseerde melk en voor het kloppen van eieren en
suiker voor vetloos biscuitgebak.
de garde gebruiken
1 Plaats de kom op het motorblok en bevestig de
verwijderbare aandrijfas.
2 Duw beide gardes
7
goed in de aandrijfkop.
3 Monteer de garde door hem zorgvuldig te draaien, totdat hij
over de aandrijfas zakt.
4 Voeg de ingrediënten aan de kom toe.
5 Zet het deksel erop – zorg ervoor dat de bovenkant van de
aandrijfas in het midden van het deksel past.
6 Zet de machine aan.
belangrijk
De garde is niet geschikt om kant-en-klare
taartmixen te bereiden, aangezien deze mengsels
te zwaar zijn en de garde zullen beschadigen.
Gebruik altijd het mes.
tips
Het beste resultaat wordt verkregen met eieren op
kamertemperatuur.
Zorg ervoor dat de kom en de garde schoon en vetvrij zijn,
voordat u ze gaat gebruiken.
b
oter en suiker kloppen
Voor het beste resultaat moet de boter eerst op
kamertemperatuur komen (20 °C) voordat hij wordt geklopt.
G
ebruik GEEN boter die rechtstreeks uit de
koelkast komt, omdat de garde hierdoor
beschadigd raakt.
Z
waardere ingrediënten zoals bloem en gedroogd fruit
moeten handmatig worden ingevouwen.
U mag de maximum capaciteit of verwerkingstijd die in de
s
nelheidstabel wordt aangegeven, niet overschrijden.
cp
vouwhulpstuk
Gebruik het vouwhulpstuk om lichte ingrediënten in
z
waardere mengsels te vouwen voor meringue, mousse en
v
ruchtenmousse.
1
Plaats de kom op het motorblok en bevestig de
verwijderbare aandrijfas.
2 Duw beide gardes
8
goed in de aandrijfkop.
3 Zet het vouwhulpstuk op de foodprocessor door voorzichtig
te draaien tot het over de aandrijfas valt.
4 Voeg de ingrediënten toe.
5 Leg het deksel erop – zorg dat de bovenkant van de
aandrijfas zich in het midden van het deksel bevindt.
6 Selecteer Auto.
tips
Voor het beste resultaat de eiwitten of room niet te lang
kloppen – het vouwhulpstuk kan het mengsel niet goed
vouwen als het geklopte mengsel te stevig is.
Vouw het mengsel niet langer dan aangegeven wordt in de
tabel met aanbevolen snelheden, aangezien de lucht dan uit
het mengsel wordt geslagen en het mengsel te slap wordt.
Ongemengde ingrediënten op het blad of de zijkanten van
de kom moeten zorgvuldig met de spatel worden
ingevouwen.
cq
schijf voor max capaciteit
Wanneer vloeistoffen worden gemengd in de kom, moet
gebruik worden gemaakt van de schijf voor maximale
capaciteit met het mes. Hierdoor wordt lekken voorkomen
en worden de hakprestaties van het mes verbeterd.
1 Zet de kom op het motorblok.
2 Monteer het meselement.
3 Voeg de ingrediënten toe die verwerkt moeten worden.
4 Zet de schijf voor maximale capaciteit over de bovenkant
van het mes; zorg er hierbij voor dat de schijf op de rand in
de kom rust
9
. Duw de capaciteitsschijf niet naar
beneden.
5 Plaats het deksel op de kom en zet de machine aan.
17
schijven voor snijden/raspen
o
mkeerbare schijven voor snijden/raspen 4mm
cr
, 2mm
cs
G
ebruik de raspzijde voor kaas, wortels, aardappelen en
v
oedingsmiddelen met een gelijksoortige textuur.
Gebruik de snijzijde voor kaas, wortels, aardappelen, kool,
k
omkommer, courgette, bieten en uien.
e
xtra fijne raspschijf
ct
V
oor het raspen van Parmezaanse kaas en aardappelen
voor knoedels.
fijne julienne
dk
G
ebruiken om aardappelen in lucifers te snijden en grof
raspen voor rösti, roerbakken en groentegarnituur.
decoratieve snijschijf
dl
Gebruiken om aardappelen, wortelen, komkommer en
voedsel met soortgelijke textuur in geribbelde plakken te
snijden
veiligheid
Verwijder het deksel nooit voordat de schijf
helemaal tot stilstand is gekomen.
Wees voorzichtig met de snijschijven ze zijn
heel erg scherp
Vul de kom niet te ver - overschrijdt de maximum
capaciteit die op de kom wordt aangegeven niet.
de snijschijven gebruiken
1 Plaats de kom op het motorblok en bevestig de
verwijderbare aandrijfas
2
.
2 Houd de schijf aan de middengreep vast en plaats hem op
de aandrijfas, met de juiste zijde naar boven gekeerd
bk
.
3 Zet het deksel op zijn plaats.
4 Doe de ingrediënten in de vulopening.
Kies de maat toevoerbuis die u wilt gebruiken. De pusher
bevat een kleinere toevoerbuis voor de verwerking van
individuele items en dunne ingrediënten.
De kleine toevoerbuis gebruiken: steek eerst de grote
pusher in de toevoerbuis.
De grote toevoerbuis gebruiken: gebruik beide pushers
tegelijkertijd.
5 Zet de machine aan en duw de ingrediënten gelijkmatig met
de stamper naar binnen steek uw vingers nooit in de
vulopening.
tips
Gebruik verse ingrediënten.
Snijd de ingrediënten niet te klein. Vul de hele breedte van
de vulopening met de ingrediënten. Zodoende kunnen de
ingrediënten tijdens de verwerking niet zijwaarts schuiven.
Gebruik anders de kleine toevoerbuis.
Bij gebruik van de julienneschijf, plaatst u de ingrediënten
horizontaal in de vulopening.
Bij gebruik van de snij- of raspschijf: voedsel dat rechtop
bl
in de vulopening wordt gezet komt er korter uit dan voedsel
dat horizontaal
bm
wordt geplaatst.
Ingrediënten die rechtop worden ingebracht worden korter
dan ingrediënten die horizontaal worden ingebracht.
Er blijven altijd restjes aan de schijf of in de kom hangen na
de verwerking.
dm
minikom met mes
Gebruik de minikom om kruiden te hakken en om kleine
h
oeveelheden ingrediënten te mengen, zoals vlees, ui,
n
oten, mayonaise, groente, puree, sauzen en babyvoeding.
De snij-/raspschijf kan ook met de minikom worden gebruikt.
Zet de minikom zonder mes in de hoofdkom en raadpleeg
d
e sectie over de snij-/raspschijf voor instructies over het in
elkaar zetten en het gebruik.
De kom niet te ver vullen.
minimes
minikom
de minikom met mes gebruiken
1
Plaats de kom op het motorblok en bevestig de
v
erwijderbare aandrijfas.
2 Zet de minikom over de verwijderbare aandrijfas – zorg dat
de uitsnijdingen zijn uitgelijnd met de lipjes
bn
op de
hoofdkom.
NB: Het deksel van de hoofdkom past niet als de minikom
niet goed is geplaatst.
3 Plaats het mes over de aandrijfas
bo
.
4 Voeg de ingrediënten toe die verwerkt moeten worden.
5 Plaats het deksel op de kom en zet de machine aan.
veiligheid
Verwijder het deksel nooit voordat het mes helemaal tot
stilstand is gekomen.
Het mes is erg scherp – ga er altijd voorzichtig mee om.
belangrijk
Verwerk geen specerijen in de keukenmachine – ze kunnen
de kunststof onderdelen beschadigen.
Verwerk geen harde ingrediënten, zoals koffiebonen,
ijsklontjes of chocolade ze kunnen het meselement
beschadigen.
tips
Kruiden worden het beste verwerkt wanneer ze schoon en
droog zijn.
Voeg altijd een klein beetje vloeistof toe wanneer u gekookte
ingrediënten tot babyvoeding verwerkt.
Snij etenswaren zoals vlees, brood, groente in blokjes van
1-2 cm, voordat u ze verwerkt.
Wanneer u mayonaise maakt, giet u de olie door de
toevoerbuis.
18
1 / 1

Kenwood FPM810 MULTI PRO SENSE Omistajan opas

Kategoria
Food processors
Tyyppi
Omistajan opas
Tämä käsikirja sopii myös