Parkside POF 1300 Operation and Safety Notes

ROUTER

OBERFRÄSE

Bedienungs- und Sicherheitshinweise

POF 1300

GB / IE / CY Operation and Safety Notes Page 5

FI Käyttö- ja turvallisuusohjeet Sivu 19

SE Bruksanvisning och säkerhetsanvisningar Sidan 31

DK Brugs- og sikkerhedsanvisninger Side 43

NO Betjenings- og sikkerhetshenvisninger Side 57

GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 69

DE / AT Bedienungs- und Sicherheitshinweise Seite 83

Kompernaß GmbH

Burgstraße 21

D-44867 Bochum (Germany)

Last Information Update · Tietojen tila · Informationsstatus

Tilstand af information · Opplysningenes gyldighet

Έκδοση των πληροφοριών · Stand der Informationen:

10 / 2007 · Ident.-No.: POF 1300102007-3

ROUTER

Operation and Safety Notes

YLÄJYRSIN

Käyttö- ja turvallisuusohjeet

ΦΡΕΖΑ

Υποδείξεις χειρισμού και ασφαλείας

OVERFRES

Betjenings- og sikkerhetshenvisninger

OVERFRÆSER

Brugs- og sikkerhedsanvisninger

ÖVERHANDSFRÄS

Bruksanvisning och säkerhetsanvisningar

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Slå opp siden med illustrasjoner før bruksanvisningen leses. Bli først kjent med alle apparatets funksjoner.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions

of the device.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med

apparatens/maskinens funktioner.

B

A

1

2

3

4

5

6

7

23

8

9

13

14

15

16

10

12

11

17

18 19

202122

24 25

C D

E F

G H

26 32

37

34

33

35 36

31 30272829

5 GB/IE/CY

Table of content

Introduction

Proper use..................................................................................................................Page 6

Features and equipment ...........................................................................................Page 6

Included items ...........................................................................................................Page 7

Technical information ................................................................................................Page 7

Safety advice

Workplace safety......................................................................................................Page 8

Electrical safety ......................................................................................................... Page 8

Personal safety ..........................................................................................................Page 9

Careful handling and use of electrical power tools ................................................Page 9

Safety advice relating speciﬁcally to this device ....................................................Page 10

Original accessories / attachments ..........................................................................Page 11

Caution utility services! ............................................................................................. Page 11

Have you understood everything? ...........................................................................Page 11

Preparing for use

Router bit set / scope of application ........................................................................Page 11

Inserting a router bit ..................................................................................................Page 12

Connecting a dust / chip vacuum extraction device ...............................................Page 12

Attaching the vacuum extraction adapter (with reducer piece) .............................Page 13

Operation

Switching on / oﬀ ......................................................................................................Page 13

Preselecting the rotation speed ................................................................................ Page 13

Table of indicative rotational speeds (for guidance only) ......................................Page 13

Setting the depth of cut .............................................................................................Page 14

Direction of feed .......................................................................................................Page 15

Routing process .........................................................................................................Page 15

Setting the guide bushing .........................................................................................Page 15

Routing with the guide bushing ................................................................................ Page 15

Routing with the guide fence ....................................................................................Page 15

Routing a circular arc proﬁle / Fig. H .......................................................................Page 16

Maintenance and cleaning

Maintenance ............................................................................................................. Page 16

Cleaning .................................................................................................................... Page 16

Disposal....................................................................................................................Page 16

Information

Service centre ...........................................................................................................Page 17

Declaration of Conformity / Manufacturer ............................................................ Page 17

6 GB/IE/CY

Introduction

Router POF 1300

Q

Introduction

Please make sure you familiarise your-

self fully with the way the device works

before you use it for the ﬁrst time and

that you understand how to handle electrical pow-

er tools correctly. To help you do this please read

the accompanying operating instructions. Keep

these instructions in a safe place. If you pass the

device on to anyone else, please ensure that you

also pass on all the documentation.

Q

Proper use

The device is intended for routing grooves, edges,

proﬁles and elongated holes and for copy routing

whilst resting ﬁrmly on wood, plastic and light con-

struction materials.

With a reduced rotational speed and the appropri-

ate router bits, the device can also be used to ma-

chine non-ferrous metals. The device is not intended

for use in the open air. The device is not intended

for commercial use. Any other use or modiﬁcation

to the device shall be considered as improper use

and could give rise to considerable dangers. The

manufacturer will not accept liability for loss or

damage arising from improper use.

Q

Features and equipment

Figure A, front of device:

1

Handle with ON / OFF switch

2

Spindle lock button

3

Spindle

4

Chip shield

5

Base plate

6

Guide plate

7

Step buﬀer

8

Dust boot

9

Stop screw for depth stop

10

Depth stop

11

Slider with index mark

12

Scale for coarse adjustment of depth of cut in mm

13

Scale for ﬁne adjustment of depth of cut in mm

The following icons / symbols are used in this instruction manual:

Read instruction manual! Safety class II

Observe caution and safety notes!

Wear hearing protection, dust protection mask,

protective glasses and protective gloves.

Caution – electric shock!

Dangerous electric current – danger to life!

Keep children and other unauthorised personnel

at a safe distance when using electrical tools.

n

0

Rated idle running speed

Keep the device away from rain or moisture.

Water entering an electrical device increases the

risk of electric shock.

V

~

Voltage

Damaged appliances, power cables and power

plugs mean potentially fatal risks from electric

shock. Regularly check the condition of the appli-

ance, the power cables and the power plugs.

W

Watts (Eﬀective power)

Dispose packaging and appliance in an

environmentally-friendly way!

7 GB/IE/CY

Introduction

14

Fine adjustment knob for depth of cut

Figure B, rear of device:

15

Clamping lever

16

Markings for zero-reset

17

Lights for cutting area

18

Tightening nut with integrated 6mm collet

19

Tightening nut with integrated 8mm collet

20

Router bit

21

Locking screw

22

Guide rail

23

ON/OFF switch

24

Safety lock-out

25

Thumbwheel for speed preselection

Figure C:

26

Guide rod for guide fence

27

Guide fence

28

Screw for the ﬁne adjustment of the guide fence

29

Stirrup for the ﬁne adjustment of the guide fence

Figure D:

30

Screw for attaching the vacuum extraction

adapter

31

Vacuum extraction adapter

32

Reducer piece

Figure E:

33

Centring pin

34

Wing nut for centring pin

35

Guide bushing

36

Guide bushing ring

37

Spanner

Q

Included items

1 Carrying case

1 Router POF 1300

1 Tightening nut with integrated 6mm collet

1 Tightening nut with integrated 8mm collet

1 Router bit set (10-piece)

1 Spanner (for tightening nuts

18

+

19

) (see Fig. E)

1 Guide bushing (see Fig. E)

1 Guide fence (see Fig. C)

1 Vacuum extraction adapter (incl. screws) (see Fig. D)

1 Reducer piece

1 Centring pin (see Fig. E)

1 Operating instructions

1 Booklet covering “Warranty and service”

Q

Technical information

Rated voltage: 230 V

~

50 Hz

Nom. power input: 1300 W

No-load speed: n

0

11000 - 28000 min

-1

Tool holder: 6 / 8mm

Plunge depth: max. 55mm

Protection class: II /

&

Noise and vibration data:

Values determined in accordance with EN 60745

The sound pressure level (A-weighted) of the

device is typically 95 dB (A). Uncertainty K=3 dB.

The sound level while working can exceed

106 dB (A).

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration a

h

= 12,065 m / s

2

Uncertainty K = 1,744 m / s

2

WARNING!

The vibration level given in

these instructions has been measured in accord-

ance with a standardised measurement procedure

speciﬁed in EN 60745 and can be used to com-

pare devices. Diﬀerent uses of the device give rise

to diﬀerent vibration levels and in many cases they

may exceed the values given in these instructions. It

is easy to underestimate the vibration load if the elec-

trical power tool is used regularly in particular cir-

cumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

8 GB/IE/CY

Introduction / Safety advice

Safety advice

J Attention! In order to protect yourself from

the danger of electric shock, injury or ﬁre when

using electrical power tools, please observe

the following safety precautions.

J Read and observe these requirements before

you use the device and keep the safety advice

in a safe place. Failure to observe the instruc-

tions and advice given below may result in

electric shock, ﬁre and / or serious injury.

Q

Workplace safety

J Keep your working area clean and clutter-free.

Ensure that your working area is well lit. Untidy

or poorly lit working areas can lead to accidents.

J Do not work with the device in potentially ex-

plosive environments in which there are inﬂam-

mable liquids, gases or dusts. Electrical power

tools create sparks, which can ignite dusts or

fumes.

J Use dust extraction or trapping equipment if

these facilities can be ﬁtted. If you use a vacu-

um dust extraction device, make sure that it is

specially designed to be used for this purpose.

The correct use of these devices reduces the

hazard presented by dust. There is the danger

of ﬁre when working with electrical devices

that have a dust bag or can be connected to a

vacuum extraction device. Under certain condi-

tions the wood dust in the dust extraction bag

(or in the vacuum‘s ﬁlter bag) can self-ignite,

e.g. as a result of ﬂying sparks generated

when machining metals or metal objects left in

wood. This can happen particularly if the

wood dust is mixed with paint residue or other

chemicals and the waste particles are hot from

prolonged machining. Therefore you must emp-

ty the dust collection bag and ﬁlter bag before

pausing or stopping work and always avoid

overheating the waste particles or the vacuum’s

ﬁlter bag.

J

Keep children and other people

away while you are operating the

electrical power tool.

Distractions can cause you to lose control of

the device.

Q

Electrical safety

To avoid danger to life

from electric shock:

J The mains plug on the device must match the

mains socket. The plug must not be modiﬁed in

any way. Do not use an adapter plug with de-

vices ﬁtted with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

J Avoid touching earthed surfaces such as pipes,

radiators, ovens and refrigerators with any part

of your body. There is an increased risk of elec-

tric shock if your body is earthed.

J

Keep the device away from rain or

moisture. Water entering an electrical

device increases the risk of electric

shock.

J Do not use the mains lead for any purpose for

which it was not intended, e.g. to carry the

device or to pull the mains plug out of the mains

socket. Keep the mains lead away from heat,

oil, sharp edges or moving parts of the device.

9 GB/IE/CY

Safety advice

Damaged or tangled mains leads or plugs in-

crease the risk of electric shock.

J

A damaged tool, mains lead or plug

presents a serious danger to life from

electric shock.

Frequently check the condition of the device,

mains lead and plug.

J Check the condition of the plug and mains lead

on your electrical tool regularly and have any

damage repaired by a competent specialist.

J When working outdoors always use extension

cables that are also approved for use outdoors.

The use of an extension cable suitable for out-

door use reduces the risk of electric shock.

J Do not use an electrical power tool with dam-

aged parts. If a dangerous situation arises pull

out the mains plug from the socket immediately.

J Warning! Never open up the device.

Always have any repairs carried out or replace-

ment parts ﬁtted at the service centre or by an

electrical equipment repair specialist.

Q

Personal safety

J Remain alert at all times and always watch

what you are doing. Work carefully when us-

ing an electrical power tool. Do not use the de-

vice if you cannot concentrate or are tired or

under the inﬂuence of drugs, alcohol or medi-

cation. Just one moment of carelessness when

using the device can lead to serious injury.

J

Wear personal protective equip-

ment and always wear safety

glasses. The wearing of personal

protective equipment such as dust masks, non-slip

safety shoes, protective gloves, safety helmets

or ear protectors, appropriate to the type of

electrical power tool used and work undertaken,

reduces the risk of injury.

J Avoid unintentional operation of the device.

Make sure that the switch is in the “OFF” posi-

tion before you insert the mains plug into the

socket. Accidents can happen if you carry the

device with your ﬁnger on the ON / OFF switch

or you have already switched the device on

before you connect it to the mains.

J Remove any setting tools or spanners before

you switch the device on. A tool or spanner left

attached to a rotating part of a device can

lead to injury.

J Do not overestimate your own abilities. Keep

proper footing and balance at all times. By do-

ing this you will be in a better position to control

the device in unforeseen circumstances.

J Wear suitable clothing. Do not wear loose cloth-

ing or jewellery. Keep your hair, clothing and

gloves clear of moving parts. If you have long

hair, wear a hair net. Clothing, jewellery or hair

that is loose or hangs from your body, head or

limbs can become trapped in moving parts.

Q

Careful handling and use

of electrical power tools

J Do not overload your electrical power tool. Al-

ways use an electrical power tool that is intend-

ed for the task you are undertaking. You will

work better and more safely if the tool is kept

within its speciﬁed operational range.

J Do not use an electrical power tool if its switch

is defective. An electrical power tool that can

no longer be switched on and oﬀ is dangerous

and must be repaired.

J Pull the mains plug from the socket before you

make any adjustments to the device, change

accessories or when the device is put away.

This precaution prevents you from unintention-

ally starting the device.

J When not in use always ensure that electrical

power tools are kept out of reach of children.

Do not let anyone use a tool with which he or

she is not familiar or who has not read the in-

structions and advice. Electrical power tools

are dangerous when they are used by inexperi-

enced people.

J Look after your tools meticulously. Check that

moving parts are working properly and move

freely. Check regularly for broken parts or

parts that are damaged to the extent they detri-

mentally aﬀect the functioning of the device.

Have damaged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

10 GB/IE/CY

Safety advice

J Keep cutting tools clean and sharp. Carefully

maintained cutting tools with sharp cutting edg-

es are less likely to jam and are easier to control.

J Use the electrical power tool, accessories,

inserted tools etc. in accordance with these

instructions and advice, and the stipulations

drawn up for this particular type of device. In

doing this, take into account the working condi-

tions and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

Safety advice relating

speciﬁcally to this device

J Securely support the workpiece. Use clamps or

a vice to grip the workpiece ﬁrmly. This is much

safer than holding it in your hand.

J Danger of fire from flying sparks!

Machining metal creates ﬂying sparks. For

this reason, always make sure that nobody is

placed in any danger and that there are no in-

ﬂammable materials near the working area.

J Warning! Be aware that persons operating

the tool or in its vicinity may be at risk of being

in contact with or inhaling dusts.

J Take all the necessary safety precautions in

relation to dusts. Working with this tool can give

rise to dusts that may be hazardous to health,

inﬂammable or explosive.

J Harmful or poisonous dusts can, for example,

arise from machining paints containing lead, or

from certain types of hardwoods or metals.

Some dusts are classed as carcinogenic. Wear

a breathing mask and use a suitable dust / chip

vacuum extraction device.

J Warning! Keep your working area clean.

Mixtures of materials can be particularly dan-

gerous. Light metal dust, for example, may

burn or explode.

J m Warning! Danger of electric shock

from metal dust!

Machining metal can result in electrically con-

ductive dust being deposited inside the device.

In these circumstances the inside of the motor

compartment must be blown out at frequent in-

tervals with compressed air, vacuum extraction

used and the device operated through a residual

current device (RCD) with a maximum trip cur-

rent of 30 mA.

J Ensure that there is adequate ventilation when

machining surfaces containing plastic or covered

with paint, varnish etc., otherwise there may be

a risk to your health through the generated dust.

J Do not machine materials containing asbestos.

Asbestos is a known carcinogen.

J Avoid contact with the rotating router bit, other-

wise there may be risk of injury .

J Do not machine moist materials or damp surfaces,

otherwise there may be a risk of electric shock.

J Never leave the device working unattended,

otherwise there may be a risk of injury or accident.

J Never use the device for a purpose for which it

was not intended. The use of electrical power

tools for purposes other than those intended can

lead to dangerous situations.

J Always work with the mains lead leading away

from the rear of the device.

J Check before use that the router is ﬁrmly seated

in position, otherwise there may be a risk of

injury or accident.

J If a dangerous situation arises, pull the mains

plug immediately out of the mains socket.

J Before you insert the mains plug into the socket,

always check that the device is switched oﬀ.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or you

have already switched the device on before

you connect it to the mains.

J Always switch on the device before guiding it

against the workpiece, otherwise there may be

a risk of injury from kick-back.

J After a routing task has been completed, lift the

device oﬀ the workpiece and turn the clamping

lever to bring the device into its top position and

then switch it oﬀ.

J Switch the device oﬀ and allow it to come to a

complete standstill before you put it down, oth-

erwise there may be a risk of injury from rotat-

ing parts.

J Never machine over metal objects, nails or

screws, otherwise there may be a risk of injury

or damage to the device.

J Hold the device only by the insulated handle if

there is the risk that you might cut through a

11 GB/IE/CY

Safety advice / Preparing for use

concealed cable or the device’s mains lead.

Contact with an electrical lead or cable means

that the metal parts of the device may also be-

come live and this can result in electric shock.

J Always keep the device clean, dry and free of

oil or grease. Dirty devices increase the risk of

injury (e.g. by slipping). You will work better

and more safely with clean cutting tools.

Q

Original accessories /

attachments

J Use only the accessories and attachments de-

tailed in the operating instructions. The use of

inserted tools or accessories other than those

recommended in the operating instructions

could lead to you suﬀering an injury.

Q

Caution utility services!

J Danger!

Ensure that you do not strike electrical cables,

gas or water pipes when you are working with

an electrical power tool. Check a wall using a

suitable detector before you drill or cut slots.

Q

Have you understood

everything?

J Once you have made yourself familiar with this

general safety advice for electrical power tools,

and with the help of the device’s operating in-

structions you now know about all the functions

of and how to handle your electrical power tool,

you are ﬁnally in a position to start work. Ob-

serving the instructions and advice will maximise

your safety while working with the device.

Q

Preparing for use

Q

Router bit set / scope

of application

Router bits (also referred to as router cutters) are

available in a wide range of qualities and designs

to suit the type of cutting and intended application.

The following descriptions give you an indicative

overview (without liability) of the scope of applica-

tion of diﬀerent router bits. The included router bit

set contains router cutters for the most common

routing tasks.

Flush trim bit with bearing:

Particularly suitable for ﬂush trimming and chamfer-

ing laminated boards, wooden beams and edgings

(plastic or veneer) in furniture making and shop ﬁtting.

The bearing allows the bit guide itself directly along

the workpiece. The most common applications of

this bit include rounding the edges of window frames,

cupboards, tabletops, shelves and mantelpieces.

Corner rounding bit with bearing:

Corner rounding bits are suitable for proﬁling edges

in frames and framework, especially working with

solid woods, such as spruce, beech, oak and alder.

Slot cutter, with two cutting edges:

Particularly suitable for solid wood, boards, e.g.

chipboard and MDF (medium density wood ﬁbre

boards) and for plastics. Suitable for milling plane

12 GB/IE/CY

Preparing for use

surfaces, slots for letters or butt jointed connections,

notches, tongue and groove joints etc.

Cove cutter bit / cove cutter bit with bearing:

Cove cutter bits are used for edge proﬁling (e.g.

concave edges), for constructing bureaux (hinged

connections with concave proﬁles), for making dec-

orative grooves, for texturing surfaces, for cutting

juice channels etc.

V-slot cutter bit:

V-slot cutter bits are almost universal in application.

They are suitable for example for making (orna-

mental) grooves, bevelling or engraving script etc.

Dovetail cutter bit, with two cutting edges:

Particularly suitable for cutting strong dovetails for

making furniture or boxes, e.g. for drawer runners

(see Fig. G).

Q

Inserting a router bit

Attention! Do not press the spindle lock button

2

before the motor has come to a standstill, other-

wise there is the risk of damage.

Attention! Tighten the tightening nut with the

spanner

37

only after a router bit has been insert-

ed. Failure to observe this advice may result in

damage to the collet.

1. Selecting the router bit

Select a router bit appropriate to the material and

suitable for the purpose. Router bits made from high

speed steel (HSS) are suitable for machining soft

materials, such as plastic or softwood. Carbide-tipped

router bits (HM) are suitable for machining hard

materials, such as hardwood or aluminium.

Note! Use only routing tools with an allowable

speed at least as high as the highest no-load speed

of the device! The shank diameter of the router bit

must correspond with that of the collet!

2. Inserting the router bit

Before carry out any work on the device, ﬁrst pull

the plug out of the mains socket. Wear protective

gloves when inserting or replacing a router bit.

j Fold down the chip shield

4

.

j Press the spindle lock button

2

and keep it

depressed. Turn the spindle

3

if necessary by

hand until it engages. Tighten the tightening

nuts (

18

or

19

) by hand on to the spindle

3

.

j Note: All the router bits in the supplied router

bit set have an 8 mm shank. Use the tightening

nut with integrated 8mm collet

19

for these and

the integrated 6 mm collet

18

for router bits

with a 6 mm shank.

j Now insert the router bit. At least 20 mm of its

shank must be inserted.

j Tighten the tightening nut (

18

or

19

) with the

spanner

37

.

j Now release the spindle lock button

2

.

j Fold up the chip shield

4

.

Note: Tighten the tightening nut with the spanner

37

only after a router bit has been inserted.

Q

Connecting a dust / chip

vacuum extraction device

Danger! Protect yourself during your work by

wearing a dust mask and use a suitable dust / chip

vacuum extraction device.

13 GB/IE/CY

Preparing for use / Operation

Q

Attaching the vacuum extraction

adapter (with reducer piece)

m Warning: Always pull the mains plug is out

of the socket before doing any work on the device.

This precaution is intended to prevent you from

unintentionally starting the device.

Note: Remove the router bit before you attach the

vacuum extraction adapter

31

.

j Place the vacuum extraction adapter

31

on to

the base plate

5

. Fasten the vacuum extraction

adapter

31

to the base plate

5

using the two

screws

30

. Screw the two screws

30

in from

below.

 If it is necessary to use the reducer piece

32

, it

can be pushed into the vacuum extraction

adapter

31

.

j Connect a vacuum extraction device suitable

for extracting dust and chips by means of a

suction hose to the vacuum extraction adapter

31

or to the reducer piece

32

.

Q

Operation

Connect the device by its mains plug to a power

source supplying 220 V - 230 V

~

50 Hz.

Q

Switching on / oﬀ

Switching on

j To switch oﬀ the device ﬁrst press the safety

lock-out

24

and keep it depressed. Then press

the ON / OFF switch

23

.

Switching oﬀ

j To switch oﬀ the device, release the ON / OFF

switch

23

again.

Illuminating the routing area

j The integrated illumination for the routing area

lights up and can be switched oﬀ again by

pressing the On / Oﬀ switch

23

.

Q

Preselecting the

rotation speed

j Set the required rotational speed using the

thumbwheel for speed preselection

25

.

1-2 = low rotational speed

3-4 = medium rotational speed

5-6 = high rotational speed

j If possible always determine the optimum setting

beforehand using a practical test.

j If you have been working for a long period using

a low rotational speed, you should cool the

device by running it at the highest speed for

about 1 minute under no-load conditions.

Q

Table of indicative rotational

speeds (for guidance only)

Material Router

bit

Speed

setting

Aluminium 4-15 mm

16-40 mm

1-2

1

Plastic 4-15 mm

16-40 mm

2-3

1-2

Chipboard 4-10 mm

12-20 mm

22-40 mm

3-6

2-4

1-3

Softwood

e.g.: spruce,

pine, fir

4-10 mm

12-20 mm

22-40 mm

5-6

3-6

1-3

Hardwood

e.g.: maple,

birch, oak,

cherry

4-10 mm

12-20 mm

22-40 mm

5-6

3-4

1-2

The indicative values in the table are for guidance

only. The required rotational speed depends on the

material and the working conditions and should be

determined by means of a practical test.

14 GB/IE/CY

Operation

Q

Setting the depth of cut

m Danger! Set the cutting depth only after the

device has been switched oﬀ!

Coarse setting of the depth of cut

1.0

3/64

1/32

16

14

13

1. Ensure that the clamping lever

15

is applied. If it

is released turn it anticlockwise until it is applied.

2. Place the device on the workpiece.

3. Turn the ﬁne adjustment knob

14

for depth of

cut until the markings for zero-reset

16

on the

back of the device are in alignment.

4. Turn the scale for ﬁne adjustment of depth of

cut in mm

13

until the “0” point aligns with the

marking on the housing.

5. Turn the step buﬀer

7

until it engages in the

lowest position.

6. Release the stop screw

9

for depth stop.

7. Release the clamping lever

15

by turning it

clockwise and press the device downwards

until the router bit comes into contact with the

workpiece surface.

8. Apply the clamping lever

15

by turning it anti-

clockwise.

9. Push the depth stop

10

downwards until it is sit-

ting at the lowest position of the step buﬀer

7

.

Press the slider with index mark

11

to position

“0” of the scale for coarse adjustment of depth

of cut in mm

12

.

10. Set the depth stop

10

to the desired routing

depth and tighten the stop screw

9

for depth

stop. After this, the setting of the slider with

index mark

11

should not be changed.

11. Release the clamping lever

15

and then guide

the device back up again.

After setting the depth of cut do not change the set-

ting of the slider with index mark

11

on the depth

stop

10

. The current depth of cut setting can now be

read on the scale for coarse adjustment of depth of

cut in mm

12

.

Example: Create a guide slot in a pine drawer:

width: 16 mm, depth: 10 mm

j Select the 16 mm slot cutter from the router bit

set and insert it as described in the section about

“Inserting a router bit”.

j Preselect a medium rotational speed (approx.

3 - 4).

j Carry out steps 1 to 9 as described in the sec-

tion above.

j Set the required depth of cut by setting the depth

stop

10

to “10” on the scale for coarse adjust-

ment of depth of cut in mm

12

. Now tighten

the stop screw for depth stop

9

.

j Secure the workpiece and carry out the routing

process as described in the following sections.

Fine setting the depth of cut

The depth of cut can be adjusted using the ﬁne ad-

justment knob

14

for depth of cut. (1 division =

0.1 mm / 1 revolution = 1.5 mm) max. + - 8 mm

movement.

Example: Take the device back up and measure

the machined slot depth (required ma-

chined depth = 10 mm / actual = 9.8 mm)

j Place the device in a position which allows the

router bit to be lowered without obstruction.

j Release the clamping lever

15

by turning it

clockwise and press the device carefully down-

wards until the depth stop

10

sits on the step

buﬀer

7

.

j Apply the clamping lever

15

by turning it anti-

clockwise.

j Turn the scale for ﬁne adjustment of depth of

cut in mm

13

to “0”. Release the stop screw

9

for depth stop

10

.

j Use the ﬁne adjustment knob

14

to change the

depth of cut by 0.2 mm / 2 divisions (= diﬀer-

ence between required and actual), turn clock-

wise, in the direction of the + arrow.

15 GB/IE/CY

Operation

j Tighten the stop screw

9

for depth stop

10

again.

j Release the clamping lever

15

by turning it

clockwise and then guide the device back up

again. Check the depth of cut by carrying out

a further practical test.

Setting the depth of cut using the step

buﬀer

You can use the step buﬀer

7

to make greater

depths of cut in several successive stages in which

less material is removed.

j Set the required depth of cut with the lowest

step of the step buﬀer

7

(as described

above).

j Afterwards the higher steps can be used for

the ﬁrst few cuts.

Q

Direction of feed

m Danger! When machining with the direction

of rotation the router can be ripped out of your

hands. This may cause injury.

J Always machine against the direction of

rotation of the router bit!

Q

Routing process

j Adjust the depth of cut as described above.

j Place the device on the workpiece and switch

it on.

j Release the clamping lever

15

by turning it

clockwise and press the device downwards un-

til the depth stop

10

runs against the workpiece.

j Lock the device by turning the clamping lever

15

anticlockwise.

j Carry out the routing process using uniform

speed and pressure

j Stop the routing process by lifting the device

from the workpiece and switching it oﬀ.

Q

Setting the guide bushing

j Insert the guide bushing

35

from below into the

guide plate

6

.

j Fasten the guide bushing

35

to the base plate

5

using the two screws

30

of the vacuum ex-

traction adapter. Make sure that the guide

bushing

35

is the right way round - the guide

bushing ring

36

must be facing downwards.

Q

Routing with the guide bushing

Note! When using the guide bushing, the template

must have a minimum thickness of 8 mm.

Note! The template must be at least as thick as

the guide bushing ring

36

of guide bushing

35

.

Note! Choose a router bit with a smaller diameter

than the internal diameter of the guide bushing.

By using the guide bushing

35

you can superimpose

templates or patterns on to the workpiece.

j Place the device with the guide bushing

against the template.

j Release the clamping lever

15

by turning it

clockwise and lower the device until the previ-

ously set depth of cut is reached.

j Now guide the device with the projecting

guide bushing along the template, whilst apply-

ing light pressure.

Q

Routing with the guide fence

j Insert the guide fence

27

into the guide rails

22

of the base plate

5

and fasten it into place to

suit the required dimension using the locking

screw

21

.

16 GB/IE/CY

Operation / Maintenance and cleaning / Disposal

j Place the guide fence

27

against the edge of

the workpiece. Now carry out the ﬁne adjust-

ment. Turning the screw for the ﬁne adjustment

28

of the guide fence clockwise reduces the

distance. Turning the screw for the ﬁne adjustment

28

of the guide fence anticlockwise increases the

distance. The stirrup

29

for the ﬁne adjustment

of the guide fence indicates the corrections on

the scale.

j After the device has been lowered, apply the

clamping lever

15

by turning it anticlockwise.

j Carry out the routing process using uniform

speed and pressure (see Figs. F, G).

j After the routing process lift the device from the

workpiece and switch it oﬀ.

Q

Routing a circular arc

proﬁle / Fig. H

j Reverse the guide fence

27

(stop edge faces

upwards) and push it into the guide rails

22

of

the base plate

5

. Fasten it in place with the

locking screws

21

.

j Now screw the centring pin

33

with the wing

nut

34

for centring pin through the outer hole

of the guide fence

27

. Use the small recess at

the side of the spanner

37

to provide counter

pressure.

j Insert the centring pin

33

into the marked centre

of the circle. Now carry out the ﬁne adjustment.

Turning the screw for the ﬁne adjustment of the

guide fence

28

clockwise reduces the radius.

Turning the screw for the ﬁne adjustment of the

guide fence

28

anticlockwise increases the

radius. Notice that the stirrup

29

for the ﬁne

adjustment of the guide fence moves with refer-

ence to the scale of the guide fence

27

during

this process.

j Now guide the device with even speed and

pressure over the workpiece surface. Notice

that the path of guide fence

27

is controlled by

the setting on the stirrup

29

for the ﬁne adjust-

ment of the guide fence.

j Note: You can make changes to the radius of

the circle to be machined by changing the

position of the guide fence

27

.

Q

Maintenance and cleaning

Q

Maintenance

j The device requires no maintenance.

j Have repairs carried out only by an electrical

power tool specialist or your service centre.

Q

Cleaning

m Warning! Pull the mains lead out of the mains

socket before you clean the device, otherwise there

may be risk of injury .

j Always keep the device and the ventilation

slots clean, dry and free of oil or grease. Dirty

devices increase the risk of injury (e.g. by slip-

ping). You will work better and more safely with

clean cutting tools.

j Do not allow any liquids to enter the inside of

the device, otherwise there may be a risk of

electric shock. Use a dry cloth to clean the

housing.

Never use petrol, solvents or cleaning agents

that might attack plastic.

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electrical

power tools with the household

rubbish!

In accordance with European Directive

2002 / 96 / EC (covering waste electrical and elec-

tronic equipment) and its transposition into national

legislation, worn out electrical power tools must be

collected separately and taken for environmentally

compatible recycling.

Contact your local refuse disposal authority for

more details of how to dispose of your worn out

electrical devices.

17 GB/IE/CY

Information

Q

Information

Q

Service centre

The service centre for your country is shown in the

warranty documentation.

J Have your device repaired only by qualiﬁed

specialist personnel using original manufactur-

er parts only. This will ensure that your device

remains safe to use.

J If the plug or mains lead needs to be replaced,

always have the replacement carried out by

the manufacturer or its service centre. This will

ensure that your device remains safe to use.

Q

Declaration of Conformity /

Manufacturer

We, Kompernaß GmbH, Burgstr. 21,

D-44867 Bochum, Germany, declare

that this product complies with the

following EU directives:

Machinery Directive (98 / 37 / EC)

EU Low Voltage Directive (2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

Type / device description:

Parkside Router POF 1300

Bochum, 31.10.2007

Hans Kompernaß

- Managing Director -

We reserve the right to make technical modiﬁcations in the course

of further development.

18

19 FI

Sisällysluettelo

Johdanto

Tarkoituksenmukainen käyttö ....................................................................................Sivu 20

Varusteet .................................................................................................................... Sivu 20

Toimituksen sisältö ..................................................................................................... Sivu 21

Tekniset tiedot ............................................................................................................ Sivu 21

Turvallisuusohjeita

Työpaikkaturvallisuus ................................................................................................ Sivu 22

Sähköturvallisuus .......................................................................................................Sivu 22

Henkilöturvallisuus ....................................................................................................Sivu 23

Sähkötyökalujen huolellinen käsittely ja käyttö .......................................................Sivu 23

Laitekohtaisia turvallisuusohjeita ..............................................................................Sivu 24

Alkuperäiset varusteet / lisälaitteet ...........................................................................Sivu 25

Huomio: Johtoja! .......................................................................................................Sivu 25

Ymmärsitkö kaiken?...................................................................................................Sivu 25

Käyttöönotto

Jyrsinsetti / käyttöalueet ............................................................................................Sivu 25

Jyrsintyökalun asennus .............................................................................................. Sivu 26

Liitä pölyn / lastujen poistoimu .................................................................................Sivu 26

Imuadapterin (ja vähennysosan) asennus ...............................................................Sivu 26

Käyttö ........................................................................................................................Sivu 26

Päälle kytkeminen / päältä kytkeminen ....................................................................Sivu 27

Kierrosluvun esivalinta ..............................................................................................Sivu 27

Kierroslukutaulukko: ohjearvot .................................................................................Sivu 27

Jyrsintäsyvyyden säätö .............................................................................................Sivu 27

Jyrsintäsuunta ............................................................................................................ Sivu 28

Jyrsintä ....................................................................................................................... Sivu 28

Kopiohylsyn asennus ................................................................................................Sivu 29

Jyrsintä rinnakkaisvasteella .......................................................................................Sivu 29

Jyrsintä harpin avulla / kuva H .................................................................................Sivu 29

Huolto ja puhdistus

Huolto ........................................................................................................................ Sivu 29

Puhdistus ....................................................................................................................Sivu 30

Hävittäminen ......................................................................................................Sivu 30

Tietoja

Huolto ........................................................................................................................ Sivu 30

Yhdenmukaisuusvakuutus / Valmistaja .....................................................................Sivu 30

20 FI

Yläjyrsinkone POF 1300

Q

Johdanto

Tutustu ehdottomasti ennen ensimmäistä

käyttöönottoa laitteen toimintoihin ja

perehdy sähkötyökalun oikeaan käyttöön.

Lue lisäksi seuraava käyttöohje. Säilytä tämä käyt-

töohje huolellisesti. Luovuta kaikki asiakirjat laitteen

mukana, jos laite vaihtaa omistajaa.

Q

Tarkoituksenmukainen käyttö

Laite on suunniteltu puuhun, muoviin ja kevytraken-

nemateriaaleihin tehtävien urien, särmien, proﬁilien

ja pitkittäisreikien jyrsintään kiinteällä alustalla sekä

kopiojyrsintään.

Jos kierroslukua lasketaan ja käytetään sopivaa jyr-

sintä, voidaan työstää myöskin kirjometalleja.

Laitetta ei ole suunniteltu ulkokäyttöön. Laite ei ole

tarkoitettu ammattimaiseen käyttöön. Kaikki muu

käyttö ja jokainen laitteeseen tehty muutos ei ole

tarkoituksenmukaista käyttöä ja siinä piilee ilmeinen

vaara loukkaantua. Valmistaja ei vastaa tarkoituk-

senvastaisesta käytöstä aiheutuvista vahingoista.

Q

Varusteet

Kuva A, laitteen etupuoli:

1

Kahva PÄÄLLÄ- / PÄÄLTÄ-kytkimellä

2

Karan lukituspainike

3

Kara

4

Lastusuojus

5

Pohjalevy

6

Liukulevy

7

Vaiherajoitin

8

Suojamansetti

9

Syvyysrajoittimen lukitusruuvi

10

Syvyysrajoitin

11

Kelkka indeksiosoittimineen

12

Asteikko: jyrsintäsyvyyden karkeasäätö mm:ssä

13

Asteikko: jyrsintäsyvyyden hienosäätö mm:ssä

14

Kiertosäädin: jyrsintäjyrkkyyden hienosäätö

Johdanto

Tässä käyttöohjeessa käytetään seuraavia kuvakkeita / symboleja:

Lue käyttöohje! Suojausluokka II

Huomioi varoitus- ja turvaohjeet!

Käytä aina laitteella työskennellessäsi suojalase-

ja, kuulo- ja hengityssuojaimia sekä asianmukai-

sia työkäsineitä.

Varo sähköiskua!

Vaarallisia sähköjännitteitä – hengenvaara!

Pidä lapset ja muut henkilöt loitolla

sähkötyökalun käytön aikana.

n

0

Mitoitusjoutokäyntinopeus

Ehkäise laitteen kastuminen. Veden joutuminen

laitteeseen aiheuttaa sähköiskun vaaran.

V

~

Voltti (Vaihtojännite)

Vaurioitunut laite, verkkojohto tai verkkopistoke

merkitsevät sähköiskun aiheuttamaa hengenvaaraa.

Tarkasta säännöllisesti laitteen, verkkojohdon,

verkkopistokkeen kunto.

W

Watti (Vaikutusteho) Hävitä pakkaus ja laite ympäristöystävällisesti!

21 FI

Johdanto

Kuva B, laitteen takapuoli:

15

Kiristysvipu

16

Nollapisteen tasauksen merkki

17

Jyrsintäalueen valaistus

18

Hattumutteri integroidulla tankoistukalla 6 mm

19

Hattumutteri intergroidulla tankoistukalla 8 mm

20

Jyrsinterä

21

Kiinnitysruuvi

22

Johde

23

PÄÄLLÄ- / PÄÄLTÄ-kytkin

24

Käynnistyslukitus

25

Asetuspyörä kierrosluvun esivalintaa varten

Kuva C:

26

Rinnakkaisvasteen ohjaustanko

27

Rinnakkaisvaste

28

Rinnakkaisvasteen hienosäätö

29

Hienosäädin

Kuva D:

30

Ruuvi poistoimuadapterin kiinnitykseen

31

Poistoimuadapteri

32

Vähennysosa

Kuva E:

33

Keskiöintituurna

34

Keskiöintituurnan siipimutteri

35

Kopiohylsy

36

Kopiohylsyn vierintärengas

37

Avain

Q

Toimituksen sisältö

1 kantolaukku

1 yläjyrsinkone POF 1300

1 hattumutteri intergroidulla tankoistukalla 6 mm

1 hattumutteri intergroidulla tankoistukalla 8 mm

1 jyrsintäsetti (10-osainen)

1 avain (hattumutterille

18

+

19

) (katso kuva E)

1 kopiohylsy (katso kuva E)

1 rinnakkaisvaste (katso kuva C)

1 poistoimuadapteri (mukaan lukien ruuvit)

(katso kuva D)

1 vähennysosa

1 keskiöintituurna (katso kuva E)

1 käyttöohje

1 vihkonen „Takuu ja huolto“

Q

Tekniset tiedot

Nimellisjännite: 230 V

~

50 Hz

Nimellisottoteho: 1300 W

Kierrosluku tyhjäkäynnissä: n

0

11000 - 28000 min

-1

Työkaluliitin: 6 / 8 mm

Jyrsinkorin liike: maks. 55 mm

Suojausluokka: II /

&

Melu- ja tärinätiedot:

Mittausarvot määritetty normin EN 60745 mukaan.

Laitteen A-painotettu äänenpainetaso on tyypillisesti

95 dB (A). Epävarmuus K=3 dB. Melutaso saattaa

työn aikana ylittää 106 dB (A).

Käytä kuulosuojaimia!

Arvioitu kiihtyvyys, tyypillisesti:

Käteen ja käsivarteen

kohdistuva värinä a

h

= 12,065 m / s

2

Epävarmuus K = 1,744 m / s

2

VAROLTUS!

Näissä ohjeissa ilmoitettu värähtely-

taso on määritetty normissa EN 60745 standardoidulla

mittausmenetelmällä ja sitä voidaan käyttää laitevertai-

lussa.

Värähtelytaso muuttuu sähkötyökalun käytön

mukaan ja se saattaa monesti ylittää tässä ohjees-

sa mainitun arvon. Värähtelyrasitusta saatetaan ali-

arvioida, jos sähkötyökalua säännöllisesti käyte-

tään tällä tavalla.

Huomio: Liikekuormituksen arvioimiseksi tietyn

työajan kestäessä on huomioitava myös ajat, jolloin

laite on sammutettuna, tai ajat, jolloin laite on käyn-

nissä, mutta ei työkäytössä. Tämä saattaa vähen-

tää merkittävästi liikerasitusta kokonaistyöskentely-

ajan kestäessä.

22 FI

Johdanto / Turvallisuusohjeita

Turvallisuusohjeita

J Huomio! Kun käytetään sähkötyökaluja on

huolehdittava seuraavista periaatteellisista tur-

vatoimenpiteistä sähköiskujen, loukkaantumisten

ja tulipalojen välttämiseksi.

J Lue nämä määräykset ensin ja noudata niitä, kun

alat käyttää laitetta. Säilytä turvallisuusohjeet

huolellisesti. Jos jäljempänä lueteltuja ohjeita ei

noudateta asiankuuluvalla tavalla, virheet saat-

tavat aiheuttaa sähköiskun, tulipalon ja / tai

vakavia loukkaantumisia.

Q

Työpaikkaturvallisuus

J Pidä työalueesi siistinä ja järjestyksessä. Pidä

huoli hyvästä valaistuksesta työalueella. Seka-

sotku ja huonosti valaistu työsalue saattavat ai-

heuttaa tapaturmia.

J Älä työskentele laitteen kanssa räjähdysalttiissa

ympäristössä, jossa on palavia nesteitä, kaasuja

tai pölyjä. Sähkötyökalut tuottavat kipinöitä, jotka

saattavat sytyttää pölyn tai höyryt palamaan.

J Käytä pölynimu- tai keruulaitteita, jos ne voi-

daan asentaa. Muista myös, että pölynimulait-

teiden täytyy olla erityisesti tähän käyttötarkoi-

tukseen sopivia. Näiden laitteiden oikeaoppinen

käyttö vähentää pölyn aiheuttamia vaaroja.

Kun työskennellään sähkökäyttöisten laitteiden

kanssa, joissa on pölypussi / -säkki tai jotka voi-

daan yhdistää pölynpoiston välityksellä vastaa-

vaan laitteeseen, on muistettava palovaaran ole-

massaolo! Epäsuotuisissa olosuhteissa, kuten esim.

kipinöiden lentäessä, hiottaessa metallia tai metal-

lin rippeitä puusta, voi puupöly pölypussissa (tai

pölynimurin suodatinpussissa) syttyä itsestään pa-

lamaan. Näin voi käydä ennen kaikkea, kun puu-

pölyyn on sekoittunut maalintähteitä tai muita ke-

miallisia aineita ja hiottava kappale on pitkän

työskentelyn jälkeen kuuma. Vältä siitä syystä eh-

dottomasti hiottavan kappaleen ja hiomalaitteen

ylikuumenemista, ja tyhjennä pölynpoistolaitteen

pöly- tai suodatinpussi aina ennen työtaukoja.

J

Pidä lapset ja muut henkilöt sähkö-

työkalun käytön aikana loitolla.

Häiriytyessäsi saatat menettää

laitteen hallinnan.

Q

Sähköturvallisuus

Vältä sähköiskusta johtuvaa

hengenvaaraa:

J Virtapistokkeen on sovelluttava pistorasiaan.

Pistoketta ei saa muuttaa millään tavoin. Älä käytä

adapteripistoketta yhdessä suojamaadoitettujen

laitteiden kanssa. Pistokkeet, joihin ei ole tehty

muutoksia, sekä sopivat pistorasiat vähentävät

sähköiskun vaaraa.

J Vältä fyysistä kosketusta maadoitettuihin pintoihin

kuten putkiin, lämmityslaitteisiin, sähköliesiin ja

jääkaappeihin. Jos kehosi on maadoitettu, se

lisää sähköiskun vaaraa.

J

Pidä laite suojassa sateelta ja kosteu-

delta. Veden pääsy sähkölaitteeseen

lisää sähköiskun riskiä.

J Älä käytä kaapelia muihin tarkoituksiin, esim.

laitteen kantamiseen, sen ripustamiseen johonkin

tai vetääksesi pistokkeen pistorasiasta. Pidä

kaapeli loitolla kuumuudesta, öljystä, terävistä

reunoista tai laitteen liikkuvista osista. Vialliset

tai mutkaiset ja kiertyneet kaapelit tai rikkinäiset

pistokkeet lisäävät sähköiskun vaaraa.

Sivu latautuu ...

Parkside POF 1300 Operation and Safety Notes

Parkside POF 1300 Operation and Safety Notes

muilla kielillä

Liittyvät paperit

Muut asiakirjat