Denver HBO-6750WHITE Ohjekirja

Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

Original Instruction
DENVER HBO-6750
Before operating this vehicle, read all the instructions for safe assembly and operations. User’s manual can
guide you through the functions and usage of the hoverboard. Before using this hoverboard, familiarize
yourself with how to operate, so that you can keep the hoverboard in the best condition possible.
This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision
Warning : Lithium battery inside
www.denver-electronics.com
ENG 1
ENG 2
Chapter 1 General information
We urge owners of this hoverboard model to charge and store the
hoverboards in a safe place. To increase the safety and life of the batteries
associated with this model it is important not to charge this model if the
temperature is below 5 or above 45. In addition, the charger must be
disconnected when the battery is fully charged. Only use the charger that
is packaged with the hoverboard model.
1.1. The risk of driving
- Learn how to drive safely before you drive fast on the hoverboard.
- Failing, losing control, crashing, including violating the rules in the
user’s manual can lead to injury.
- Speed and range may differ based on rider weight, terrain,
temperature, and driving style.
- Make sure to wear helmet and protective clothing before using the
hoverboard.
- Make sure to read the manual carefully before using the hoverboard.
- Only for use in dry weather.
- We do not recommend the use of any balance scooters on public
roads. For domestic use only.
1.2 The preparation before operation
Before using, the battery should be fully charged. Please check Chapter 6.
ENG 3
1.3 The weight limitation of the operator
The reason of the weight limitation: 1. guarantee the safety of the operator; 2. decrease the damage of
overloading.
Maximum load: 120kg.
Chapter 2 Operating the hoverboard
2.1. Description and identification
2.2. Calibration
If your hoverboard seems to pull to the left or right, you may need to recalibrate its sensors. Step as below: Step
1: Shut down/level the hoverboard
Step 2: Press and hold power button (keep holding buton pressed even though it starts flashing red and beep.
And wait until it gives a long constant beep)
Step 3: Stop holding the power button and now the calibration is finished.
Built in Self-Balance function, it is easy for driving.
2.3. Operating principal
Pedal
Indicator
Fender
Fender
Tire
Tire
Power On/Off
Decorative Light
ENG 4
- The hoverboard uses Dynamic equilibrium, using internal gyroscope and acceleration sensors. The status of
the hoverboard is controlled by the center-of gravity. It is adjusted by motor, which is controlled by the servo
control system. When you lean forward, it will sense your actions to accelerate. When you need to turn, slow it
down and move your foot forwards or backwards then the center-of gravity of the body moves left or right
therefore the hooverboard can sense moving left or right.
- The hooverboard has inertial dynamic stabilization system, so it can keep anterior-posterior balance but
cannot guarantee the left and right. So when turning, the scooter needs to be operated slowing, otherwise,
you may be injured.
2.4. Learn how to use it
Step 1: Press the power button to turn on the hoverboard.
Step 2: Put the hoverboard on a flat ground and make sure all safety measures are taken. Put one foot on the pad
that will trigger the pedal switch to turn on the operation indicator, after the system enters the selfbalancing mode,
put the other foot on the pad.
Step 3: Take control of the hoverboards’ forwards or backwards, do remember the movement of your body should
not be abrupt.
If you are not in a balanced condition when you trigger the foot-switch, the buzzer will alarm, and the warning LED
will light. The system is not in a self-balanced condition. Without a balanced condition, you should not operate the
hoverboard. Then you need to calibrate the sensors, see point 2.2.
Step 4: Control the left and right direction of the hoverboard.
Step 5: Before you get off, make sure that the hoverboard is still in balanced condition and stopped, then step off
one foot, then the other foot.
NOTE:
ENG 5
You should never ride sideways or turn on a slope. It will lead
to a fall and injury.
2.5. Always react on alarms
Hoverboard will not operate in the following situations:
- During operation, if the system runs an error, the hoverboard will prompt operators in different ways such as
prohibit riding, alarm indicator lights, buzzer alarm beeps intermittently the system cannot enter selfbalancing
mode.
- When stepping on the hoverboard the platform moves forwards or backwards more than 10 degrees, the unit
will not operate.
- The voltage of the battery is too low.
- During charging.
- During operation, the platform turns upside down will prohibit operation.
- Over speeding.
- The battery is not charged enough.
- Tire stall, two seconds later the scooter enters power off mode.
- The battery voltage is lower than the protection value, 15 seconds later the hoverboard enters into power off
mode.
- Continuing large current discharge (such as a long-time climbing a very steep slope)
Tilt right foot forward- Turn Left
Tilt left foot forward- Turn Right
You should never turn violently when
driving fast.
ENG 6
When the hoverboard enters into the shutdown state (when the
battery is low), the system will lock down the machine
automatically. It can be unlocked when you press the power
button. When the battery has been depleted or the system gives
out information with safety shutdown, please do not continue
to drive the hoverboard, otherwise, the hoverboard cannot
balance for the lack of battery. In this condition, the driver is
likely to be harmed. If the battery reaches the minimum, the
continued driving of the hoverboard will negatively affect the
battery’s life.
- The product should only be used in temperatures between -
10°C - +45°C.
2.6. Riding practice
Before you drive the hoverboard, please make sure you are familiar with the skills of driving it. Always practice with
someone ready to hold/catch you.
- Use casual (but not loose) clothes and flat shoes in order to retain your body’s flexibility.
- Please go to open spaces to practice driving the hoverboard until you can easily get on /off.
- Make sure that the surface is level.
- When you are driving on different terrain, you must slow down.
- Hoverboard is a driving tool designed for a smooth road. Reduce speed if you drive the hoverboard on a
rough surface.
- Before driving: Read Chapter 4 on maximum speed and Chapter 5 on safe driving thoroughly
Chapter 3 Pedal Sensor and Indicator operation
3.1. Pedal sensor
The hoverboard has 4 sensors below the pedal, when the operator steps on the pedal, the hoverboard will adjust
itself to a balancing pattern automatically. When riding it, you have to make sure that the pedal is being fully
stepped on, please do not step on the parts outside the pedal. Do not put things on the pedals to make the
hoverboard operate by itself and increase the possibility of crashing and even cause personal injury and damage
to the hoverboard itself.
3.2. Battery & Operation Indicators
The indicator is located in the middle of the hoverboard. It is used for operation information.
- Battery indicator on the hoverboard will show green color as long as there is sufficient power on the
battery to drive.
- Battery indicator on the hoverbard will show red color when battery power is down(15-20% left) and you will you
need to stop driving and start to recharge the hoverboard.
ENG 7
- Battery indicator on the hoverboard will show RED and have WARNING ALARM SOUND when battery power
has run out and you must stop driving immediately. The hoverboard will now shut down without further notice
and the hoverboard will then loose balance. You may have risk to get injured if still try to keep driving.
- Operation indicator: When the pedal is triggered, the operation indicator will light then the system comes into
operating condition; when the system runs an error, the indicator will turn red.
Chapter 4 Range and speed
4.1. Range per charge
The range per charge is related to many factors, for example:
- Topography: On even roads the range per charge will be increased, on uneven terrain, it will be decreased.
- Weight: The weight of the operator can influence the driving distance.
- Temperature: Extreme temperature will decrease the driving distance.
- Maintenance: If the hoverboard is charged properly and the battery is kept in good condition, this will
maximize the driving distance.
- Speed and driving style: Keeping a steady speed will increase the driving distance, on the contrary, frequent
start, stop, acceleration, deceleration will reduce the distance.
4.2. Max. Speed
- The maximum speed of the hoverboard is rated at 15km/h but depends on the charging condition of the
battery, the condition/angle of the surface, wind direction, and the driver’s weight. If the battery is fully
charged, the surface is very level or even angled downward, there is a tailwind, and the driver is not very
heavy, the maximum speed may exceed 15km/h.
- Approaching its maximum speed, the hoverboard emits a warning signal, and speed should be reduced.
- We recommend driving the hoverboard at speeds that are comfortable to you and not driving the hoverboard
at speeds exceeding 12km/h.
- In the permissive speed, the hoverboard can balance itself well.
Chapter 5 Safe driving
This chapter will focus on safety, knowledge and warnings. Before operating this vehicle, read all the instructions
for safe assembly and operation.
- Before starting, familiarize yourself with how to operate, so that you can keep the hoverboard in the best
condition.
ENG 8
- When you are driving the hoverboard, make sure that all safety measures are taken. You should be wearing a
helmet, knee pads, elbow pads and other protective gear.
- The driver should not wear loose or hanging clothing, shoelaces, etc. that can get caught in the wheels of the
hoverboard.
- Hoverboard is only for personal entertainment. You are not allowed to ride it on public streets.
- Hoverboard is not allowed on the motor vehicle lanes.
- Children, the elderly, pregnant women are not allowed to drive.
- Persons with reduced balancing capacity should not drive the hoverboard.
- Do not drive the hoverboard under the influence of alcohol or any other substance.
- Do not carry items when driving.
- Please be alert to things in front of you, maintaining good vision will help you drive hoverboard safely.
- Relax your legs while driving, knees slightly bent, it can help maintain balance when encountering uneven
ground.
- In the process of driving, make sure that your feet are always steeping on the pedals.
- Hoverboard can only carry one person.
- Do not start or stop suddenly.
- Avoid driving on steep slopes.
- Do not drive the hoverboard up against a fixed object (f.inst. a wall or other structure) and continue driving the
hoverboard.
- Do not drive in dimly lit or dark places.
- Driving the hoverboard is at your own risk and the company is not responsible for any accidents or
damage you may cause.
- Ensure the vehicle speed is safe to yourself and others, and be ready to stop at any time when operating.
- When you are driving the hoverboard, please keep a certain distance from each other to avoid collisions. --
When steering you should use your body’s center of gravity, the violent shift of center of gravity may
cause you to wreck or fall off the hoverboard.
- Do not drive backwards for long distances, drive backwards at high speeds, turn at high speeds and drive
too fast.
- Do not drive when raining or expose the hoverboard to other wet conditions. Only to be driven in dry
weather.
- Avoid driving on obstacles and avoid snow, ice, and slippery surfaces.
- Avoid driving on items made of cloth, small branches and stones.
- Avoid driving in narrow spaces or where there is an obstacle.
- Jumping on or off the hoverboard can and will cause damage that is not covered by warranty. -
Risk of personal injury. Personal damage or abuse related to “trick riding” is not covered by the company and
voids any warranty.
Chapter 6 Charging the hoverboard
This chapter mainly discusses the charging methods, how to maintain the battery, the safety issues you need to
pay attention to, and battery specifications. For safety of yourself and others, and extend the battery’s life and
improve battery performance, please make sure to follow the following operations.
6.1. Low battery
When you find the battery indicator is red and flashing, it indicates low battery. It is recommended that you stop
driving. When the power is low, there is not enough energy for your normal driving, then the system will
automatically tilt the base of the platform to prohibit the operator’s use. It is very easy to fall if you insist on driving
at this time, and negatively affect battery’s life.
ENG 9
Do not use the battery in the following cases.
Giving out some odor or excessive heat.
Leakage of any substance.
It is prohibited to disassemble the battery.
Do not touch any substance leaking out of the battery.
Do not let children and animals touch the battery.
Batteries contain dangerous substances inside. It is forbidden to open the battery and to stick objects into the
battery.
Use only the supplied charger.
Don’t over charge lithium batteries. The battery pack consists of lithium batteries.
NOTE:
When you find the battery indicator is green and flashing then after some time it will change to red light and the
alarm will beep. Now it does not allow you to drive anymore. It indicates low battery. It is recommended that you
stop driving and recharge the hoverboard. When the battery is low, there is not enough power for normal driving.
The operational system of the hoverboard will automatically tilt the platform forward to prohibit use. This could
cause the driver to fall off the hoverboard and become injured.
CAUTION
- When the charging. Do not ride the hoverboard!
- When charging ongoing then the LED light of the battery charger is red color.
- When charging is finished then LED light of the battery charger turns into green color.
- When charging finished unplug the battery charger from the mains power supply and from the hoverboard.
6.2. Charging steps
- Make sure that the hoverboard, the charger and the DC power socket on the hoverboard are kept
dry.
- Note: ONLY use the supplied charger labelled HLT-180-4201500 with the following
output voltage to charge this hoverboard: 42V - 1.5A.
- Using another charger may damage the product or create other potential risks.
- Plug the power adapter into the DC power port on the back of the hoverboard and a standard power outlet.
- Make sure the green indicator on the adaptor lights up.
- When the red indicator lights on the charger indicate charging properly, otherwise check if the line is
connected properly.
- When the indicator light on the charger changes from red to green, this indicates that the battery is fully
charged.
- In this case, please stop charging. Over charging will affect the battery life.
- Charging may take up to 3.5 - 4 hours. Do not charge the battery for more than 4 hours. Disconnect the
charger from the hoverboard and the power supply after 4 hours. Overcharging will reduce the lifetime of the
battery.
- The product should not be charged over longer periods.
ENG 10
- Never charge the product without supervision.
- The product should only be charged in temperatures between 0°C - +45°C.
- If charging at lower or higher temperatures, there is a risk that the performance of the battery will be reduced
and a potential risk of damage to the product and personal injury.
- Charge and store the product in an open, dry area and away from flammable materials (i.e. materials that
may burst into flames).
- Do not charge in sunlight or near open fire.
- Do not charge the product immediately after use. Let the product cool down for one hour before charging.
- If the product is left with other persons for example during a holiday period, it should be partially charged (20-
50% charged). Not fully charged.
- Do not remove the product from the packaging, charge it fully and then put it back into the packaging. When
shipped from the factory, the product has often been partially charged. Keep the product in a partially charged
state, until it is going to be used.
- Only use the DC connector to connect with the DC cable from the charger
that comes with the hoverboard.
- Do not insert any foreign objects into DC connector.
- Risk of arcing! Never bridge the DC charging with metal objects!
Chapter 7 The maintenance of the hoverboard
The hoverboard needs to be maintained. This chapter mainly describes the relevant steps and important
operation reminders to maintain it. Please make sure that the power and charge coil are off before you do the
following operation. You should not operate when the battery is charging.
7.1. Cleaning
Make sure the power and the charge coil are off.
Wipe the shell of hoverboard with soft cloth.
Make sure that water and other liquids do not enter the internal
parts of the balance scooter as this may permanently damage the
electronics/batteries of the scooter. There is a risk of personal
injury.
ENG 11
7.2. Storage
If the storage temperature is below 0°C, please do not charge the hoverboard. You can place it in a warm
environment (5-30°C) for charging.
You can cover the hoverboard, in order to prevent dust.
Store the hoverboard indoors put it in a place with a dry and suitable environment.
If used at lower or higher temperatures, there is a risk that the performance of the battery will be reduced
and a potential risk of damage to the product and personal injury.
Store the product at temperatures between 5°C - 30°C. (optimum storage temperature is 25°C)
Charge and store the product in an open, dry area and away from flammable materials (i.e. materials that
may burst into flames).
Do not store the product in sunlight or near open fire.
If the product is left with other persons for example during a holiday period, it should be partially charged
(20-50% charged). Not fully charged.
When shipped from the factory, the product has often been partially charged. Keep the product in a
partially charged state, until it is going to be used.
The hoverboard must cool down for at least 1 hour before being packed.
Must not be left inside a warm car sitting in the sun.
'
To protect user safety, users are forbidden to open the
hoverboard, or you give up your warranty rights.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
ENG 12
Electric and electronic equipment and included batteries contains materials, components and substances that
can be hazardous to your health and the environment, if the waste material (discarded electric and electronic
equipment and batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.
This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other
household waste, but should be disposed of separately.
As the end user it is important that you submit your used batteries to the approriate and designated facility. In
this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the
environment.
All cities have established collection points, where electric and electronic equipment and batteries can either
be submitted free of charge at recycling stations and other collection sites, or be collected from the
households. Additional information is available at the technical department of your city.
DENVER ELECTRONICS A/S
Omega 5A, Soeften,
DK-8382 Hinnerup
Denmark
Please enter: www.denver-electronics.com to obtain the electronic version of the manual.
ENG 13
ENG 14
EC Declaration of Conformity (Machine Directive)
The undersigned
Company Name: DENVER ELECTRONICS A/S
Address: Omega 5A, Soeften, 8382 Hinnerup, Denmark
Certifies that the design and manufacturing of this product
13677-06/20/00001-13677-06/20/01000
Serial number: 13678-06/20/00001-13678-06/20/00500
13679-06/20/00001-13679-06/20/00500
Confirms to the following directives:
Machine directive 2006/42/EC
Product Brand Name:
DENVER
Product Model No.:
H
BO-6
7
50
Product Type:
Hoverboard
Year of Fabrication:
2020
MDStandards:
Annex1 of 2006/42/CE, EN ISO 12100:2010, EN 60335-1: 2012 + A11:2014
And there fore complies with the essential requirements of the Machine Directive.
The identity and signature of the person empowered to draw up the declaration and compile the technical
Files onbehalf of the manufacturer:
Signature:
FullName:
Alfred
Blank
Position:
CEO
Company:
DENVER
ELECTRONICS
A/S
Date:
27
th
July 2020
Originalbedienungsanleitung
DENVER HBO-6750
www.denver-electronics.com
Lesen Sie vor dem Betrieb des Fahrzeugs alle Montage- und Betriebsanleitungen. Die Bedienungsanleitung
erklärt die Funktionen und die Verwendung des Hoverboard. Machen Sie sich vor der Verwendung des
hoverboard mit der Bedienung vertraut, sodass Sie den Hoverboard im besten Zustand halten.
- Das externe flexible Kabel dieses Transformators kann nicht ersetzt werden: Wenn das DC-Eingang
beschädigt ist, muss der Transformator entsorgt werden.
-Dieses Gerät darf von Kindern unter 8 Jahren und von Personen mit eingeschränkter körperlicher,
sensorischer oder geistiger Leistungsfähigkeit oder ohne Erfahrung oder Kenntnisse verwendet werden,
wenn sie ordnungsgemäß überwacht werden oder ihnen Anleitungen für den sicheren Gebrauch des Geräts
gegeben wurden und sie die damit verbundenen Risiken verstehen. Kinder dürfen nicht mit dem Gerät
spielen. Reinigung und Pflege dürfen nicht von Kindern ohne Aufsicht durchgeführt werden.
DEU 1
Warnung: Lithiumbatterie innen
Kapitel 1 Allgemeine Informationen
Wir bitten den/die Besitzer/-in dieses Hoverboard-Modells
nachdrücklich, dieses Hoverboard-Modell an einem sicheren
Platz zu laden und aufzubewahren. Um die Sicherheit der in
diesem Modell eingebauten Batterie zu erhöhen und ihre
Lebensdauer zu verlängern, ist es wichtig, dass dieses Modell
bei Temperaturen unter 5
oder über 45
nicht geladen
wird. Des Weiteren muss das Ladegerät getrennt werden,
wenn die Batterie vollständig geladen ist. Verwenden Sie nur
das Ladegerät, das mit diesem Hoverboard-Modell
mitgeliefert wird.
1.1. Risiken beim Fahren
WARNUNG
- Lernen Sie zunächst sicheres Fahren, bevor Sie mit dem
Hoverboard schnell fahren.
- Nichtbeachtung, der Verlust der Kontrolle, Stürze und
Regelverstöße können zu Verletzungen führen.
- Geschwindigkeit und Reichweite hängen vom Gewicht des
Fahrers, dem Gelände, der Temperatur und dem Fahrstil
ab.
- Tragen Sie einen Helm und Schutzkleidung, wenn Sie mit
dem Hoverboard fahren.
DEU 2
- Lesen Sie die Bedienungsanleitung aufmerksam durch,
bevor Sie mit dem Hoverboard fahren.
- Verwenden Sie den Hoverboard nur bei trockenem Wetter.
- Wir empfehlen, den Hoverboard nicht auf öffentlichen
Straßen zu verwenden.
- Nur für den privaten Gebrauch.
1.2. Vorbereitung
Laden Sie zunächst den Akku vollständig auf. Siehe Kapitel 6.
1.3. Gewichtsbeschränkung
Grund für die Gewichtsbeschränkung: 1. Gewährleistung der Sicherheit des Fahrers; 2.
Vermeidung von Schäden durch Überlastung. Höchstlast: 120 kg.
Kapitel 2 Bedienungshinweise
Hoverboard
2.1. Übersicht
2.2. Kalibrierung
Zieht Ihr Hoverboard nach links oder rechts, müssen die Sensoren kalibriert werden. Gehen Sie wie
folgt vor:
Schritt 1: Bringen Sie Ihr Hoverboard in eine waagerechte Position und schalten Sie es aus
Pedal
Anzeige light
Fender
Fender
Power on
Gleichstromport
Reifen Dekoratives Licht Reifen
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154

Denver HBO-6750WHITE Ohjekirja

Tyyppi
Ohjekirja
Tämä käsikirja sopii myös