Yamaha DRX-730 Omistajan opas

MICRO COMPONENT SYSTEM

DRX-730

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

i

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou de

méthodes autres que ceux décrits ci-dessous, peuvent

entraîner une exposition à un rayonnement dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die

Einstellung bzw. die Ausführung von anderen als in dieser

Anleitung beschriebenen Vorgängen kann zu Gefährdung

durch gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande av

åtgärder på annat sätt än så som beskrivs häri kan resultera i

farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure non

specificati in questo manuale possono risultare in

esposizione a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos que

no se especifican enste manual pueden causar una

exposición peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of procedures

anders dan beschreven in dit document kan leiden tot

blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или выполнение

настроек или процедур, не указанных в данной

инструкции, может привести к воздействию опасного

излучения.

CAUTION VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID EXPOSURE TO

BEAM.

VARNING

SYNLIG OCH / ELLER OSYNLIG

LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.

STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA /

TAI NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO

SÄTEESEEN.

VARNING SYNLIG OCH / ELLER OSYNLIG

LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.

BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE

LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET.

NICHT DEM STRAHL AUSSETZEN.

ATT ENTI ON RADIATION VISIBLE ET / OU INVISIBLE

LORSQUE L’APPAREIL EST OUVERT. EVITEZ TOUTE

EXPOSITION AU FAISCEAU.

ПРЕДУПРЕЖДЕНИЕ ПPИ OTKPЫTИИ УCTPOЙCTBA

BЫ MOЖETE ПОДBEPГHУTЬСЯ ВОЗДЕЙСТВИЮ

BИДИMOГO И/ИЛИ HEBИДИMOГO ЛAЗEPHOГO

ИЗЛУЧEHИЯ. ИЗБЕГAЙTE BOЗДЕЙСТВИЯ ЛУЧA.

Hyou2.fm i ページ２００８年８月２７日　水曜日　午後３時２７分

ii

En

English

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle tai

muille vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse

for stråling.

Bemærk: Netafbryderen STANDBY/ON er sekundært

indkoblet og ofbryder ikke strømmen fra nettet. Den

indbyggede netdel er derfor tilsluttet til lysnettet så længe

netstikket sidder i stikkontakten.

N

Observer: Nettbryteren STANDBY/ON er sekundert

innkoplet. Den innebygdenetdelen er derfor ikke frakoplet

nettet så lenge apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sätt än i denna

bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Observera! Strömbrytaren STANDBY/ON är sekundärt

kopplad och inte bryter inte strömmen från nätet. Den

inbyggda nätdelen är därför ansluten till elnätet så länge

stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-

ja roiskevedelle.

Huom. Toiminnanvalitsin STANDBY/ON on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon

aina silloin, kun pistoke on pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

Information for Users on Collection and Disposal of Old Equipment and

used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products and batteries should not be mixed with general household waste. For proper treatment,

recovery and recycling of old products and used batteries, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

iii

En

1.

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2.

Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at

least 10 cm on the top, 10 cm on the left and right, and 10 cm

on the back of this unit.

3.

Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4.

Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e., a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5.

Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping

or splashing. On the top of this unit, do not place:

—Other components, as they may cause damage and/or

discoloration on the surface of this unit.

—Burning objects (i.e., candles), as they may cause fire,

damage to this unit, and/or personal injury.

—Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6.

Do not cover this unit with a newspaper, tablecloth, curtain,

etc., in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire, damage

to this unit, and/or personal injury.

7.

Do not plug in this unit to a wall outlet until all connections

are complete.

8.

Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9.

Do not use force on switches, knobs and/or cords.

10.

When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11.

Do not clean this unit with chemical solvents; this might

damage the finish.

12.

Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Ya m a ha will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13.

To prevent damage by lightning, keep the power cord

disconnected from a wall outlet or the unit during a

lightning storm.

14.

Do not attempt to modify or fix this unit. Contact qualified

Ya m a ha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15.

When not planning to use this unit for long periods of time

(i.e., vacation), disconnect the AC power plug from the wall

outlet.

16.

Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17.

Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

18.

Before moving this unit, press STANDBY/ON to set the unit

in standby mode, then disconnect the AC power plug from

the AC wall outlet.

19.

The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

20.

Excessive sound pressure from earphones and headphones

can cause hearing loss.

■

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc

tray and other openings to look into inside.

■

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

Caution: Read this before operating your unit.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off. This state is called the standby mode. In this

state, this unit is designed to consume a very small quantity of

power.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

LASER

Type Semiconductor laser AlGaInP

Wave length 655 nm (DVD)

790 nm (VCD/CD)

Output Power 5 mW (DVD)

7 mW (VCD/CD)

Beam divergence 20 degree

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

iv

En

English

■

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note:

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■

Special Instructions for U.K. Model

■

Handling the remote control

•The area between the remote control and this unit must be

clear of large obstacles.

•Do not spill water or other liquids on the remote control.

•Do not drop the remote control.

•Do not leave or store the remote control in the following

types of conditions:

—places of high humidity, such as near a bath

—places of high temperature, such as near a heater or a stove

—places of extremely low temperatures

—dusty places

•Do not expose the remote control sensor to strong lighting,

in particular, an inverter type fluorescent lamp; otherwise,

the remote control may not work properly. If necessary,

position this unit away from direct lighting.

■

Notes on batteries

•Change all of the batteries if you notice that the operation

range of the remote control decreases.

•Use AA, R6, UM-3 batteries.

•Make sure that the polarities are correct. See the illustration

inside the battery compartment.

•Remove the batteries if the remote control is not used for an

extended period of time.

•Do not use old batteries together with new ones.

•Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully

as these different types of batteries may have the same shape

and color.

•If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

•Do not throw away batteries with general house waste;

dispose of them correctly in accordance with your local

regulations.

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (

http://www.yamaha-hifi.com/

or

http://www.yamaha-uk.com/

for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any

charge for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along

with a statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge

service and the product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modiﬁcations or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the

proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards

in force in the country where it is used.

(4) Accidents, lightning, water, ﬁre, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard speciﬁcation of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are deﬁned in our website at

http://www.yamaha-hiﬁ.com/

or

http://www.yamaha-uk.com/

for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer

arising from their sales/purchase contract.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

v

En

■

Legal notices

This product incorporates copyright protection

technology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise

authorized by Macrovision. Reverse engineering or

disassembly is prohibited.

■

iPod™

“Ap p l e ,” “ i P o d ,” and “iTunes” are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Bluetooth is a registered trademark of Bluetooth SIG and is

used by Yamaha in accordance with a license agreement.

DivX, DivX Ultra Certified, and associated logos are

trademarks of DivX, Inc. and are used under license.

Manufactured under license from Dolby Laboratories. Dolby

and the double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and

worldwide patents issued & pending. DTS and DTS 2.0 +

Digital Out are registered trademarks and the DTS logos and

Rights Reserved.

“HDMI”, the “HDMI” logo, and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

MPEG Layer-3 audio decoding technology licensed from

Fraunhofer IIS and Thomson multimedia.

Windows Media is either a registered trademark or trademark

of Microsoft Corporation in the United States and/or other

countries.

■

Memory backup

If the power cable is disconnected from the AC wall

outlet, the DRX-730 will save the radio presets and

other settings for at least 1 week.

■

About this manual

Unless otherwise stated, instructions in this manual

such as “press ENTER” refer to the buttons on the

remote control.

Instructions and procedures in this manual assume

that the DRX-730 is already turned on.

This manual was printed before the DRX-730 went

into production. Under our policy of continuous

improvement, design and specifications are subject to

change. In the unlikely event that an explanation in

this owner’s manual disagrees with the actual

operation on the DRX-730, the DRX-730 is to be

taken as correct.

1

En

English

1

2

3

4

5

6

7

8

9

10

Appendix

1 Introduction . . . . . . . . . . . . . . . . . . . . 2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Supplied accessories . . . . . . . . . . . . . . . . . . . . . 2

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Getting Started . . . . . . . . . . . . . . . . . 8

Installing batteries in the remote control . . 8

Connecting speakers . . . . . . . . . . . . . . . . . . . . . 9

Connecting a powered subwoofer . . . . . . . 10

Connecting antennas . . . . . . . . . . . . . . . . . . . 11

Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting a recorder (CDR, MDR, etc.) . . 14

Connecting an AV receiver or decoder . . . 15

Connecting the power cable . . . . . . . . . . . . 15

3 General Functions . . . . . . . . . . . . . . 16

Turning on the DRX-730 . . . . . . . . . . . . . . . . . 16

Selecting input sources . . . . . . . . . . . . . . . . . 16

Adjusting the volume . . . . . . . . . . . . . . . . . . . 17

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . 17

Adjusting the bass and treble . . . . . . . . . . . 18

Adjusting the balance . . . . . . . . . . . . . . . . . . . 18

Pure Direct playback mode . . . . . . . . . . . . . . 19

Using headphones . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting the display brightness . . . . . . . . 20

Using the sleep timer . . . . . . . . . . . . . . . . . . . 20

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 21

Viewing the time . . . . . . . . . . . . . . . . . . . . . . . . 22

Auto standby . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4 Playing Discs . . . . . . . . . . . . . . . . . . . 23

Using the on-screen display . . . . . . . . . . . . . 23

Playing discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Slow-motion playback . . . . . . . . . . . . . . . . . . 26

Frame-by-frame playback . . . . . . . . . . . . . . . 26

Selecting languages and audio . . . . . . . . . . 27

Selecting subtitles . . . . . . . . . . . . . . . . . . . . . . 27

Selecting camera angles . . . . . . . . . . . . . . . . 28

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Repeat playback . . . . . . . . . . . . . . . . . . . . . . . . 29

A–B repeat playback . . . . . . . . . . . . . . . . . . . . 29

Random playback . . . . . . . . . . . . . . . . . . . . . . . 30

Program playback . . . . . . . . . . . . . . . . . . . . . . 31

Searching Discs . . . . . . . . . . . . . . . . . . . . . . . . . 32

Playing JPEG slideshows . . . . . . . . . . . . . . . . 33

Using Disc Navigator with DVD-Video,

VCD, and SVCD discs . . . . . . . . . . . . . . . . . 34

Using Disc Navigator with MP3, WMA,

MPEG-4 AAC, DivX®, WMV, and JPEG

discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Viewing disc information . . . . . . . . . . . . . . . .36

Viewing the audio format . . . . . . . . . . . . . . . .36

5 Using the Tuner . . . . . . . . . . . . . . . . 37

Tuning in to radio stations . . . . . . . . . . . . . . .37

Using presets . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Radio Data System (Europe and Russia

models only) . . . . . . . . . . . . . . . . . . . . . . . . .40

6 Using the Timer . . . . . . . . . . . . . . . . 44

Setting the input source . . . . . . . . . . . . . . . . .44

Setting the on time . . . . . . . . . . . . . . . . . . . . . .45

Setting the off time . . . . . . . . . . . . . . . . . . . . . .45

Turning the timer on and off . . . . . . . . . . . . .46

7 Portable Device Playback . . . . . . . 47

Music player playback . . . . . . . . . . . . . . . . . . .47

iPod playback . . . . . . . . . . . . . . . . . . . . . . . . . . .47

USB playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Bluetooth playback . . . . . . . . . . . . . . . . . . . . . .51

8 Recording . . . . . . . . . . . . . . . . . . . . . 53

9

Audio Settings and Video Adjust

. . 54

Audio Settings menu . . . . . . . . . . . . . . . . . . . .54

Video Adjust menu . . . . . . . . . . . . . . . . . . . . . .55

10Initial Settings . . . . . . . . . . . . . . . . . 56

Initial Settings menu . . . . . . . . . . . . . . . . . . . .56

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . 61

Supported discs and formats . . . . . . . . . . . .61

Looking after discs . . . . . . . . . . . . . . . . . . . . . .64

Looking after the DRX-730 . . . . . . . . . . . . . . .65

Resetting the DRX-730 . . . . . . . . . . . . . . . . . . .65

Language, country, and region lists . . . . . .66

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .67

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Contents

2

En

Thank your for choosing the Yamaha DRX-730 DVD

Receiver. To get the most enjoyment from your new

Yamaha pro duct, please read this manual carefully,

and keep it in a safe place for future reference.

•Play the following discs: DVD-Video, DVD-VR

(DVD-R/RW/R DL discs recorded in VR mode),

VCD, SVCD, Audio CD, DTS CD

•Play the following files: MP3, WMA, MPEG-4

AAC, JPEG, WMV

1

•Official DivX

®

Ultra Certified product.

•Plays all versions of DivX

®

video (including

DivX

®

6) with enhanced playback of DivX

®

media files and the DivX

®

Media Format.

•HDMI output (1080p upscaling)

• FM/AM tuner with 40 presets

•Radio Data System (Europe and Russia models)

• D-class amp: 30 W x 2 channels into 6Ω

•Pure Direct high-fidelity playback mode

•Front panel mini jack for quick and easy playback

from portable music players.

•Front panel USB port for quick and easy playback

from USB storage devices.

•DOCK jack for connecting an optional Yamaha

iPod universal dock allows you to listen to your

iPod music in high quality. And, you can control

your iPod with the DRX-730’s remote control and

recharge it while enjoying your music.

•The DOCK jack can also be used to connect a

Ya m a h a YBA-10 Bluetooth Wireless Audio

Receiver so you can listen to the music stored on

your Bluetooth-compatible music player or

mobile phone in high quality. And you can

control your Bluetooth device with the DRX-730’s

remote control.

•Timer function

•On-screen display (OSD)

•Full-function remote control

• SCART AV jack with RGB (Europe and Russia

models)

•Optical digital output

The following accessories are included with the

DRX-730. Make sure you have them all.

Chapter 1: Introduction

Features

1. The DRX-730 can play MP3, WMA, MPEG-4 AAC, and

JPEG files stored on CD-R/RW, DVD-R/RW, and

DVD+R/RW discs or USB storage devices, and DivX

®

and

WMV files stored on CD-R/RW, DVD-R/RW, and

DVD+R/RW discs. See “Supported discs and formats” on

page 61 for full details.

Supplied accessories

1

STANDBY/ON

ZOOM

OPEN/CLOSE

ON SCREEN

423

586

90

7

VOLUME

TIMER SLEEP

MUTE

DOCK

TUNER

MEMORY

SOUND

DVD/USB

PURE DIRECT

AUX/PORTABLE

DISPLAY

DIMMER

AUDIO

SUBTITLE

PLAY MODE

ANGLE

CLEAR

BLUETOOTH

PTY SEEK

ON

MODE START

FREQ/TEXT

OFF

PRESET

MENU

INFO.

TOP MENU

SETUP

RETURN

AEAE

ENTER

BAND

AUTO/

MANUAL

Remote control

Two batteries (AA, R06, UM-3)

Video pin cable

Indoor FM antenna

AM loop antenna

Chapter 1: Introduction

3

En

English

A

STANDBY/ON

Sets the DRX-730 to on or standby (see page 16).

B

Open/Close ( )

Opens and closes the disc tray (see page 23).

C

TIMER LED

Lights up when the DRX-730 on standby and the

timer is on (see page 46).

D

HDMI LED

Lights up when the HDMI OUT is used (see page 57).

E

PROGRESSIVE LED

Lights up when progressive video is being output (see

page 57).

F

Disc tray

Used to load discs (see page 23).

G

Display

Displays various information. See “Display” on page 4

for more details.

H

Remote control sensor

Receives signals from the remote control.

I

Stop ( )

Stops playback (see page 24).

J

Play/Pause ( / )

Starts and pauses playback (see page 23).

K

USB port

Used to connect a USB storage device containing

music or picture files (see page 49).

L

PORTABLE jack

Used to connect a portable music player (see

page 47).

M

PHONES jack

Used to connect headphones (see page 19).

N Previous/Rewind ( / )

Selects earlier tracks or chapters (see page 25). Works

the same as the Rewind ( ) button on the remote

control when held down.

O Next/Fast Forward ( / )

Selects subsequent tracks or chapters (see page 25).

Works the same as the Fast Forward ( ) button on

the remote control when held down.

P INPUT control

Selects input sources (see page 16).

Q VOLUME control

Adjusts the volume (see page 17).

Front panel

STANDBY/ON

USB PORTABLE PHONES

INPUT

VOLUME

TIMER

HDMI

PROGRESSIVE

B

KLMNO P Q

9J6345 871

1

Chapter 1: Introduction

4 En

A SLEEP

Lights up when the sleep timer has been set (see

page 20).

B PRESET

Lights up when selecting radio presets (see page 40).

C STEREO

Lights up when listening to an FM station in stereo

(see page 37).

D AUTO

Lights up when Auto Tuning mode is selected. Goes

off when the Manual Tuning mode is selected (see

page 37).

E DOCK

•Lights up when an iPod is inserted in an optional

Ya maha iPod universal dock (YDS-10 or YDS-11)

that’s connected to the DOCK jack (see page 47).

•Lights up when a connection has been established

between a Bluetooth device and an optional

Ya m a h a YBA-10 Bluetooth Wireless Audio

Receiver (see page 51).

•Flashes while the optional Yamaha YBA-10

Bluetooth Wireless Audio Receiver is pairing or

searching for a Bluetooth device (see page 51).

F SHUFFLE

Lights up when shuffle playback is selected on the

iPod (see page 48).

G REPEAT

Lights up when repeat playback is selected on the

iPod (see page 48).

H Radio Data System (Europe and Russia

models)

These indicators show the types of Radio Data System

information available from the FM station that you’re

currently tuned in to. The PTY HOLD indicator

lights up when searching for Radio Data System

stations by type (see page 40).

I MUTE

Flashes when the sound is muted (see page 17).

J Information area

Displays various information, such as input source,

radio frequency, and the time.

K TIMER

Lights up when the DRX-730 is on and timer is on

(see page 46).

L TUNED

Lights up when tuned in to a radio station (see

page 37).

M MEMORY

Lights up when presetting radio stations (see

page 39).

N iPod

These indicators show which iPod menu is selected

for browsing: Playlists, Artists, Albums, Songs, or

Genres (see page 48).

O iPod control

These indicators show which cursor buttons can be

used while navigating iPod menus (see page 48).

Display

GENRES

SONGS

ALBUMS

ARTISTSPLAYLISTS

MEMORY

TUNED

TIMER

SLEEP

STEREO

AUTO

DOCK MUTE

SHUFFLE

REPEAT

PS

PTY RT CT PTY

HOLD

PRESET

A BC E IDFGH

KLM N

O

J

Chapter 1: Introduction

5 En

English

(Europe model shown here.)

A MAINS (power cable)

Connect the power cable to an AC wall outlet (see

page 15).

B HDMI output

This HDMI output can be connected to an HDMI

input on your TV (see page 13).

C AV MONITOR OUT (Europe and Russia

models)

This SCART output can be connected to a SCART

input on your TV (see page 14).

D FM ANT

The FM antenna connects here (see page 11).

E AM ANT

The AM antenna connects here (see page 11).

F SPEAKERS

Speakers are connected here (see page 9).

G SUBWOOFER OUT

A powered subwoofer (sold separately) can be

connected here (see page 10).

H AUX IN and OUT

A recording component, such as a CDR, MDR, or

cassette deck, can be connected here (see page 14).

I DOCK

An optional Yamaha iPod universal dock (YDS-10 or

YDS-11) or a Yamaha YBA-10 Bluetooth Wireless

Audio Receiver can be connected here (see pages 47

and 51).

J VIDEO OUT

This composite video output can be connected to a

composite video input on your TV (see page 12).

K COMPONENT VIDEO OUT

This component video output can be connected to a

component video input on your TV (see page 12).

L OPTICAL DIGITAL OUT

This optical digital audio output can be connected to

an optical digital audio input on a CDR or MDR

recorder or AV receiver/decoder (see pages 14 and

15).

Rear panel

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

1 B 3 4 5

6 7 8 9 J K L

1

Chapter 1: Introduction

6 En

This section provides a brief description of the remote

control’s buttons.

Tip:

•In addition to controlling the DRX-730, the

remote control can also be used to control

playback on an iPod (see page 47) or a Bluetooth

music player or mobile phone (see page 51).

A Infrared transmitter

Transmits control signals to the DRX-730 (see

page 8).

B STANDBY/ON ( )

Sets the DRX-730 to on or standby (see page 16).

C Number buttons

Enter numbers.

D SUBTITLE (BLUETOOTH OFF)

•When the input source is DVD, selects subtitles

on DVDs (see page 27).

•When the input source is DOCK, disconnects

from the currently connected Bluetooth device

and makes the DRX-730 non-discoverable (see

page 51).

E AUDIO (BLUETOOTH ON)

•When the input source is DVD, selects audio

formats and foreign-language soundtracks on

DVDs (see page 27).

•When the input source is DOCK, initiates pairing

or establishes a connection with the last used

Bluetooth device and makes the DRX-730

discoverable (see page 51).

F PLAY MODE

Displays the Play Mode menu on the connected TV

when the input source is DVD.

G Pause ( )

Pauses playback.

H Rewind ( )

Rewinds playback. Also used for slow-motion

playback and frame-by-frame playback.

I Previous ( )

•Selects earlier tracks or chapters.

•On Europe and Russia models, it also works as the

Radio Data System PTY SEEK MODE button.

J TOP MENU (INFO.)

•When the input source is DVD, displays the

DVD’s top menu.

•When the input source is DOCK, selects the iPod

control mode (see page 47).

K Cursor buttons ( )/( )/( )/( ) and ENTER

Used to navigate on-screen menus and change

settings. Also used to navigate iPod menus. The

cursor buttons are also used for radio tuning and

selecting presets.

L SETUP

Displays the Setup menu on the connected TV when

the input source is DVD.

Remote control

1

STANDBY/ON

ZOOM

OPEN/CLOSE

ON SCREEN

423

586

90

7

VOLUME

TIMER SLEEP

MUTE

DOCK

TUNER

MEMORY

SOUND

DVD/USB

PURE DIRECT

AUX/PORTABLE

DISPLAY

DIMMER

AUDIO

SUBTITLE

PLAY MODE

ANGLE

CLEAR

BLUETOOTH

PTY SEEK

ON

MODE START

FREQ/TEXT

OFF

PRESET

MENU

INFO.

TOP MENU

SETUP

RETURN

AEAE

ENTER

BAND

AUTO/

MANUAL

1

B

5

4

7

M

6

8

9

J

L

N

O

P

R

S

T

Q

l

g

j

U

V

W

X

Y

b

Z

a

c

d

e

f

i

h

k

3

K

Chapter 1: Introduction

7 En

English

M MEMORY

Used to store radio presets (see page 39).

N AUTO/MANUAL

Selects the Auto and Manual Tuning modes (see

page 37).

O BAND

Selects the FM and AM radio bands (see page 37).

P DVD/USB

Selects the DVD and USB input sources (see page 16).

Q AUX/PORTABLE

Selects the AUX and PORTABLE input sources (see

page 16).

R SOUND

Used to adjust the bass, treble, and balance (see

page 18).

S TIMER

Sets the timer (see page 44).

T SLEEP

Sets the sleep timer (see page 20).

U OPEN/CLOSE ( )

Opens and closes the disc tray (see page 23).

V ON SCREEN

Displays information about the currently playing disc

on the connected TV.

W ZOOM

Zooms the picture (see page 28).

X ANGLE

Selects camera angles on DVDs (see page 28).

Y Stop ( )

Stops playback.

Z CLEAR

Clears entered numbers and deletes steps in the

program.

a Fast forward ( )

Fast forwards playback. Also used for slow-motion

playback and frame-by-frame playback.

b Play ( )

•Starts playback.

•On Europe and Russia models, it also works as the

Radio Data System PTY SEEK START button.

c Next ( )

•Selects subsequent tracks or chapters.

•On Europe and Russia models, it also works as the

Radio Data System FREQ/TEXT button.

d MENU

•Displays a DVD’s menu. (May work the same as

the TOP MENU button with some DVDs.)

•When the input source is USB, displays Disc

Navigator.

e RETURN

Returns to the previous menu.

f VOLUME (+/–)

Adjusts the volume (see page 17).

g TUNER

Selects the TUNER input source (see page 16).

h DOCK

Selects the DOCK input source (see page 16).

i MUTE

Mutes and unmutes the sound (see page 17).

j PURE DIRECT

Selects the Pure Direct playback mode (see page 19).

k DISPLAY

•Displays the time.

•When the input source is DVD and a disc is being

played, also displays the audio format.

l DIMMER

Dims the DRX-730’s display (see page 20).

1

8 En

This chapter explains how to install the batteries in

the remote control and how to connect speakers and

other components to the DRX-730.

1 Push the tab on the battery compartment

cover in the direction of the arrow and remove

the cover.

2 Insert the supplied batteries into the battery

compartment with the correct polarity

(+ and –).

3 Replace the battery compartment cover.

Notes:

•If the operating range of the remote control

decreases, replace all of the batteries with new

ones.

•Do not use old and new batteries together.

•Do not use different types of batteries together,

such as alkaline and manganese. Although they

may look similar, each type has its own

characteristics.

•When the batteries run out, remove them from

the remote control immediately to prevent an

explosion or acid leak.

•Always follow the battery disposal regulations for

your area.

•If a battery starts leaking, dispose of it

immediately. Be careful not to let leaking battery

acid come into contact with your skin or clothing.

Before inserting new batteries, wipe the battery

compartment clean.

The remote control has an operating range of up to 6

meters (20 feet). When using the remote control,

point it toward the DRX-730’s remote control sensor,

which is next to the display, see below.

Notes:

•Be careful not to spill liquid on the remote

control.

•Be careful not to drop the remote control.

•Do not leave the remote control in the following

places: hot or humid places, such as near a heater

or in a bathroom; extremely cold places; dusty

places.

Chapter 2: Getting Started

Installing batteries in the

remote control

Push here

Operating range

STANDBY/ON

USB PORTABLE PHONES

INPUT

VOLUME

TIMER

HDMI

PROGRESSIVE

30 30

Up to 6 m

(20 feet)

Chapter 2: Getting Started

9 En

English

Connect the NX-E700 speakers to the DRX-730 as shown below.

Notes:

•Do not connect the power cable to the DRX-730

until all other connections have been completed.

•Be sure to connect the right speaker to the

terminals labelled “R,” and the left speaker to the

terminals labelled “L”.

•Make sure the exposed strands of each wire are

not touching any other wires or any metal parts of

the DRX-730, as this could seriously damage the

DRX-730 and your speakers.

•Do not connect speakers with an impedance

lower than the minimum impedance stated on the

rear of the DRX-730.

•Use magnetically shielded speakers if you intend

to position them close to a CRT-type TV. If they

cause picture interference, move them away from

the TV.

Connecting speakers

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

Left speaker

DRX-730

Right speaker

Speaker cables

(Europe model shown here.)

2

Chapter 2: Getting Started

10 En

Speaker cables consist of two insulated wires running

together. Speaker connections are polarized and use

positive (+) and negative (–) terminals that are color-

coded red and black, respectively. To help you

connect the wires correctly, the positive wire is

usually marked with a stripe or some other identifier.

All you need to do is to connect the marked wire to

the positive (+) terminals on the DRX-730 and

speakers, and connect the unmarked wire to the

negative (–) terminals. If you get them crossed over,

your speakers will be out of phase and the sound will

be unnatural and lack bass, so take care.

1 Strip about 10 mm (3/8 in.) of insulation from

the end of each wire, and twist the exposed

strands together to prevent possible short

circuits.

2 Push open the speaker terminal lever, insert

the wire into the hole, and then close the lever.

You c an connect a powered subwoofer (sold

separately) to the DRX-730’s SUBWOOFER OUT

jack for a really deep bass sound.

Using an audio pin cable (sold separately),

connect the DRX-730’s SUBWOOFER OUT jack to

the powered subwoofer’s input jack.

Notes:

•Do not connect the power cables to the DRX-730

and powered subwoofer until all other

connections have been completed.

•The SUBWOOFER OUT jack outputs the low-

frequency sounds of a downmix created from all

of the channels available in the source material.

Connecting speaker cables

10 mm (3/8 in.)

Red: positive (+)

Black: negative (–)

Connecting a powered

subwoofer

INPUT

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

Audio pin cable

Powered

subwoofer

(Europe model shown here.)

Chapter 2: Getting Started

11 En

English

To listen to FM and AM radio, you must connect the

supplied antennas to the DRX-730. If radio reception

is poor in your area or you want to improve reception,

you can connect outdoor FM and AM antennas.

Consult an qualified antenna installer in your area for

more details.

■ Antenna grounding

For maximum safety and minimum interference,

connect the AM ANT GND terminal to a good earth

ground, such as a metal stake driven into moist earth.

1 Connect the supplied indoor FM antenna to

the DRX-730’s FM ANT jack.

2 Site the antenna away from the DRX-730,

speaker cables, and power cables.

Notes:

•Do not connect the power cable to the DRX-730

until all other connections have been completed.

•Before deciding where to install the antennas

permanently, tune in to an AM or FM radio

station and adjust the position of the AM or FM

antenna, respectively, to find the best reception.

•If you connect an outdoor AM antenna, connect

the supplied AM loop antenna as well.

1 Assemble the antenna’s stand as shown.

If you intend to mount the antenna on a wall, you

do not need to assemble the stand.

2 Push open the AM ANT terminal lever, insert

the AM loop antenna’s wires into the holes,

and then close the lever.

•If both of the wires on your antenna are black, this

means they are not polarized and can be

connected either way around.

•If one of the wires on your antenna is white and

the other one is black, connect the white wire to

the AM ANT terminal, and connect the black

wire to the GND terminal.

3 Site the antenna away from the DRX-730,

speaker cables, and power cables.

Connecting antennas

Connecting the FM antenna

HDMI

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

T

IN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX VIDEO OUT

P

Y

R

P

B

R

Indoor FM antenna

(supplied)

AM loop antenna

(supplied)

Earth

ground

(Europe model shown here.)

Connecting the AM loop antenna

White

Black

GND terminal

AM ANT terminal

2

Chapter 2: Getting Started

12 En

You c an connect the DRX-730 to a TV by using any

one of four different connection types: HDMI,

component video, composite video, or SCART

(Europe and Russia models). The type you choose

will depend on the connections supported by your

TV. Refer to your TV owner’s manual for details.

HDMI provides the best picture quality. Component

video offers the next best picture quality and the

DRX-730’s component video output supports

progressive scanning for even better picture quality. If

your TV doesn’t support HDMI or component video,

use composite video. Some DRX-730 models have a

SCART jack that can output composite video or RGB

component video.

Notes:

•Do not connect the power cable to the DRX-730

until all other connections have been completed.

•Turn off your TV before connecting it to the

DRX-730.

Tip:

•If your TV has an audio output, you can connect it

to the DRX-730’s AUX IN jacks and listen to your

favorite TV programs through the speakers

connected to the DRX-730.

If your TV doesn’t support HDMI or component

video, you can connect the DRX-730 to your TV with

the supplied video pin cable.

Use the supplied video pin cable to connect the

DRX-730’s VIDEO OUT jack to a composite video

input on your TV.

If your TV supports component video but not HDMI,

you can connect the DRX-730 to your TV with a

component video cable. This will provide better

picture quality than a composite video connection.

Using a component video cable (sold separately),

connect the DRX-730’s COMPONENT VIDEO OUT

jacks to a component video input on your TV.

Notes:

•If you connect a TV that does not support

progressive scanning, make sure the Component

Out setting is set to Interlace. If it’s set to

Progressive, the TV may display no picture.

•If you use the COMPONENT VIDEO OUT and

HDMI connections simultaneously, the

COMPONENT VIDEO OUT jacks may output

progressive video regardless of the Component

Out setting.

Connecting a TV

Composite video connection

VIDEO

IN

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

Video pin cable

(supplied)

TV

(Europe model shown here.)

Component video connection

Y PB PR

COMPONENT

VIDEO IN

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

Component video cable

(sold separately)

TV

(Europe model shown here.)

Chapter 2: Getting Started

13 En

English

If your TV has an HDMI input, you can connect it to

the DRX-730 with an HDMI cable and enjoy the best

possible picture quality.

Using an HDMI cable (sold separately), connect

the DRX-730’s HDMI jack to an HDMI input on

your TV.

Note:

•You must set the DRX-730’s HDMI resolution

and HDMI color settings to match the capabilities

of your HDMI TV (see page 57). If you select the

wrong resolution, you may loose the picture

altogether.

■ Supported HDMI output resolutions

* If your HDMI-compatible TV does not support the above

resolutions, the picture may not display correctly.

* The DRX-730 is designed to be connected to an HDMI

component. If it’s connected to a DVI component, normal

operation may not be possible depending on the DVI

component.

■ HDMI audio output

Normally, the speakers connected to the DRX-730 are

used to output the sound. However, you may want to

listen through your HDMI TV’s speakers, in which

case you can turn HDMI audio output on and off as

follows.

1 Set the DRX-730 to standby.

2 While holding down Stop ( ) on the

DRX-730, press STANDBY/ON, keeping

Stop ( ) pressed until “DVD — NO REQ.”

appears on the display.

3 Press Play/Pause ( / ) repeatedly to select

“HDMI AUDIO ON.”

If you change your mind at this point, select

“DVD — NO REQ.” instead.

4 Press STANDBY/ON.

HDMI Audio output is turned on and the

DRX-730 goes on standby. Press STANDBY/ON

again to turn it back on.

To turn HDMI Audio output off, repeat the above

procedure but select “HDMI AUDIO OFF” in

step 3.

Note:

•The audio output by the HDMI jack is always

2-channel PCM.

■ About HDMI

HDMI stands for High-Definition Multimedia

Interface. An extension of the DVI (Digital Video

Interface) standard used to connect computer

displays, HDMI was designed as the next generation

digital interface standard for TVs and AV equipment,

allowing uncompressed digital video and digital

audio in various formats to be delivered on a single

cable. With HDMI, separate cables for video and

audio connections are no longer necessary. And

because it’s digital, it delivers unimpaired high quality

video and audio. In addition, HDMI supports the

HDCP (High Bandwidth Digital Content Protection)

system that’s used to protect copyrighted video and

audio content from illegal copying.

HDMI connection

North America models Other models

1080p/60 Hz 1080p/60 Hz (NTSC)

1080p/50 Hz (PAL)

1080i/60 Hz 1080i/60 Hz (NTSC)

1080i/50 Hz (PAL)

720p/60 Hz 720p/60 Hz (NTSC)

720p/50 Hz (PAL)

480p/60 Hz 480p/60 Hz (NTSC)

576p/50 Hz (PAL)

480i/60 Hz 480i/60 Hz (NTSC)

576i/50 Hz (PAL)

HDMI

IN

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

HDMI cable

(sold separately)

HDMI-compatible TV

(Europe model shown here.)

2

Chapter 2: Getting Started

14 En

If your TV has a SCART jack, you can connect it to

the DRX-730’s AV MONITOR OUT jack and enjoy

composite video or RGB component video.

Using a SCART cable (sold separately), connect

the DRX-730’s AV MONITOR OUT jack to a SCART

input on your TV.

Notes:

•By default, the AV MONITOR OUT jack is set to

output composite video. To output RGB

component video, change the AV Monitor Out

setting to RGB (see page 57).

•To use the AV MONITOR OUT jack’s RGB

component video capability, you must use a

SCART cable with all 21 pins wired.

You c an connect a recording component, such as a

CDR, MDR, or casette recorder, to the DRX-730 for

recording and playback.

1 Using an audio pin cable (sold separately),

connect the DRX-730’s AUX OUT jacks to the

audio input on your recording component.

2 Using another audio pin cable (sold

separately), connect the DRX-730’s AUX IN

jacks to the audio output on your recording

component.

■ Digital recording

If your recording component has an optical digital

input, you can connect it to the DRX-730’s OPTICAL

DIGITAL OUT jack and record digitally.

See “Recording” on page 53 for more details.

Notes:

•Do not connect the power cable to the DRX-730

until all other connections have been completed.

•Turn off the recording component before

connecting it to the DRX-730.

•The OPTICAL DIGITAL OUT outputs audio

only when the input source is DVD or USB, and

with some discs and files, recording may not be

possible due to copy protection.

SCART connection (Europe and

Russia models only)

HDMI

MAINS

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

MIN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

SPEAKERS VIDEO OUT

P

Y

R

P

B

R

SPEAKER

6

SCART input

SCART cable

(sold separately)

TV

(Europe model shown here.)

Connecting a recorder (CDR,

MDR, etc.)

IN

AUDIO

L

IN

OUT

R

OPTICAL

DIGITAL

HDMI

AM

ANT

GND

FM

UNBAL.

75

OUT

OPTICAL

VIDEO

OUT IN

COMPONENT

DIGITALDOCK

AV MONITOR OUT

AUX

OUT

SUBWOOFER

VIDEO OUT

P

Y

R

P

B

R

Recording component

(CDR, MDR, casette deck)

Audio pin

cables (sold

separately)

Optical cable

(sold separately)

(Europe model shown here.)

Sivu latautuu ...

Yamaha DRX-730 Omistajan opas

Tämä käsikirja sopii myös

Yamaha DRX-730 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat