Yamaha R-N402 Omistajan opas

Kategoria
Radios
Tyyppi
Omistajan opas
RU
NL
ES
IT
SV
G
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
DE
FR
EN
Network Receiver
Réseau Ampli-Tuner
R-N402/R-N402D
i En
English
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Top: 30 cm (11-3/4 in)
Rear: 20 cm (7-7/8 in)
Sides: 20 cm (7-7/8 in)
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord
disconnected from a wall outlet or the unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Be sure to read the “Troubleshooting” section in the owner’s
manual on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press A downward to turn off this
unit and then disconnect the AC power plug from the AC wall
outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave this unit alone.
19 When us
ing this unit for a long time, this unit may become
w
arm. Turn the system off, then leave this unit alone for
cooling.
20 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like. When you dispose of batteries,
follow your regional regulations.
22 Excessive sound pressure from earphones and headphones can
cause hearing loss.
Caution
Do not touch the surface marked with this
label.
The surface may become hot during
operation.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Special Instructions for U.K. Model
Caution: Read this before operating your unit.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by A. This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Do not use this unit within 22 cm (9 inches) of persons with a heart
pacemaker implant or defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical
facilities.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
Make sure that neither core is connected to the earth terminal
of the three pin plug.
1 En
English
ADDITIONAL
INFORMATION
ADVANCED
OPERATION
BASIC
OPERATION
PREPARATION INTRODUCTION
INTRODUCTION
What you can do with this unit ................................. 2
Sources that can be played back on this unit ................. 2
Mastering useful apps (MusicCast CONTROLLER).... 3
Supplied accessories ................................................... 3
Controls and functions ............................................... 4
Front panel ..................................................................... 4
Front display .................................................................. 6
Rear panel ...................................................................... 7
Remote control............................................................... 8
PREPARATION
Connections ............................................................... 10
Connecting the speakers .............................................. 11
Connecting the FM/AM antennas (R-N402) ............... 12
Connecting the DAB/FM antenna (R-N402D)............ 12
Connecting the network cable ..................................... 13
Preparing a wireless antenna ....................................... 13
Connecting power cable .............................................. 13
Turning on the unit ...................................................... 13
Connecting to a network .......................................... 14
Sharing the iOS device setting..................................... 15
Using the WPS push button configuration .................. 16
Set the wireless network connection manually............ 17
Connecting a mobile device to the unit directly
(Wireless Direct) ..................................................... 18
Verify the network connection status .......................... 19
BASIC OPERATION
Playback .................................................................... 20
Playing a source........................................................... 20
Switching information on the front display................. 20
Using the sleep timer ................................................... 21
Listening to FM/AM radio (R-N402)...................... 22
FM/AM tuning............................................................. 22
Using preset functions ................................................. 22
Radio Data System tuning
(Only for U.K. and Europe models) ........................ 25
Listening to FM radio (R-N402D)........................... 26
FM tuning .................................................................... 26
Using preset functions ................................................. 26
Radio Data System tuning
(Only for U.K. and Europe models) ........................ 29
Listening to DAB radio (R-N402D)......................... 30
Preparing the DAB tuning ........................................... 30
Selecting a DAB radio station for reception................ 30
Using preset function................................................... 31
Displaying the DAB information................................. 32
Checking reception strength of each DAB channel
label ......................................................................... 33
Playing back music via Bluetooth ............................34
Connecting a Bluetooth device (pairing) ..................... 34
Playing back Bluetooth device contents ...................... 34
Disconnecting a Bluetooth connection ........................ 35
Playing back music stored on media servers
(PCs/NAS) ..............................................................36
Setting the media sharing of music files...................... 36
Playback of PC music contents ................................... 37
Listening to Internet radio .......................................38
Registering favorite Internet radio stations
(bookmarks)............................................................. 39
Playing back music with AirPlay.............................40
Playback of iPod/iTunes music contents ..................... 40
Playing back music stored on a USB storage
device ......................................................................41
Connecting a USB storage device ............................... 41
Playback of USB storage device contents ................... 41
Registering the current playback song/station
(Preset function) ....................................................43
Registering to a preset ................................................. 43
Recalling a preset......................................................... 43
ADVANCED OPERATION
Configuring playback settings for different
playback sources (OPTION menu)......................44
OPTION menu items ................................................... 44
Configuring various functions (SETUP menu) ......45
SETUP menu items ..................................................... 45
Network ....................................................................... 46
Bluetooth ..................................................................... 47
Balance ........................................................................ 48
Max Volume ................................................................ 48
InitialVolume............................................................... 48
AutoPowerStby (Auto Power Standby)....................... 48
Configuring the system settings
(ADVANCED SETUP menu)...............................49
ADVANCED SETUP menu items .............................. 49
Selecting the remote control ID (REMOTE ID).......... 49
Setting tuner frequency step (TU) ............................... 49
Restoring the default settings (INIT)........................... 49
Updating the firmware (UPDATE) ............................. 50
Checking the firmware version (VERSION)............... 50
Updating the unit’s firmware via the network.......51
ADDITIONAL INFORMATION
Troubleshooting.........................................................52
Error indications on the front display.....................57
Supported file formats ..............................................57
Specifications .............................................................58
Trademarks ...............................................................59
Contents
“Note” indicates precautions for use of the unit and its feature limitations. y indicates supplementary explanations for better use.
This manual explains operations using the supplied remote control.
In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific type of mobile
device is noted in explanations as needed.
2 En
INTRODUCTION
This unit is a network receiver compatible with a network source such as a media server and mobile device.
It supports playback from not only analog sources such as a CD player but also Bluetooth devices and network streaming
services.
*
You need a commercially available wireless router (access point) when you use a mobile device.
1 Play back the Internet radio (p. 38)
2 Play back the streaming service
(see the supplement for each service.)
3 Play back music files stored on your PC (p. 36)
4 Play back music files stored on your NAS
(p. 36)
5 Play back music files with AirPlay (p. 40)
6 Play back audio content from Bluetooth
devices (p. 34)
7 Play back music files stored on your USB
device (p. 41)
8 Play back your external component (p. 10)
9 Listening to radio (p. 22, 26, 30)
y
For details on connecting the external devices, see “Connections” (p. 10).
What you can do with this unit
Sources that can be played back on this unit
5V
A
SPEAKERS
USB
PHONES
VOLUME
SELECT
Wi
BLUETOOTH
Fi
RETURN
PUSH ENTER
CONNECT
DISPLAY MODE
MEMORY BAND
PRESET
TUNING
BASS
TREBLE
INPUT
This unit
1 Internet
2 Streaming service
Modem
Router*
3 PC
5 AirPlay (iTunes)
4 NAS
5 AirPlay (iPhone/iPad/iPod touch)
6 Bluetooth
7 USB device
8 CD player etc.
Mobile
device
9 Radio
What you can do with this unit
3 En
English
INTRODUCTION
You can operate and program the unit, or play streaming services via this unit, by installing the free dedicated MusicCast
CONTROLLER app on a mobile device. For details, search for “MusicCast CONTROLLER” on the App Store or
Google Play.
MusicCast CONTROLLER capabilities
Basic operations of the unit (turn on/standby, adjust volume and select input)
Play songs stored on computers (servers)
Select an Internet radio station
Play music stored on mobile devices
Play music on streaming service
Distribute and receive audio between the unit and other Yamaha MusicCast supported devices
See MusicCast Setup Guide for details.
Check that the following accessories are supplied with the product.
Mastering useful apps (MusicCast CONTROLLER)
Supplied accessories
Remote control
FM antenna (R-N402)AM antenna (R-N402)
Batteries (x2)
(AA, R6, UM-3)
DAB/FM antenna (R-N402D)
*
One of the above is supplied depending
on the region of purchase.
4 En
1 A (power)
Turns on/off (standby) the unit.
2 STANDBY/ON indicator
Brightly lit: Power is on
Dimly lit: Standby mode
3 Front display
Shows information about the operational status of this
unit.
4 DISPLAY
Selects the information displayed on the front display
(p. 20).
5 MODE
Sets the FM band reception mode to automatic stereo
or monaural (p. 22, 26).
6 MEMORY
Registers the current radio station as a preset when
TUNER is selected as the input source (p. 23, 27, 31).
Registers the current playback song or streaming
station as a preset when NET, USB are selected as the
input source (p. 43).
7 BAND
Sets the radio tuner band when TUNER is selected as
the input source. (p. 22, 26, 30)
8 PRESET j / i
Recalls a preset radio station (p. 24, 28, 31) or song/
streaming station (p. 43).
9 BLUETOOTH indicator
Lights up when the unit is connecting to a Bluetooth
device.
0 Wi-Fi indicator
Lights up when the unit connects to a wireless
network.
It also lights up if you register the unit with the
MusicCast CONTROLLER app, even if the unit is
connected to a wired network.
A Remote control sensor
Receives infrared signals from the remote control.
B TUNING jj / ii
Selects the tuning frequency (p. 22, 26) or a DAB
radio station (p. 30) when TUNER is selected as the
input source.
Controls and functions
Front panel
5V
A
SPEAKERS
USB
PHONES
VOLUME
SELECT
Wi
BLUETOOTH
Fi
RETURN
PUSH ENTER
CONNECT
DISPLAY MODE
MEMORY BAND
PRESET
TUNING
BASS
TREBLE
INPUT
1 2 3 0954 6 7
I KE JC
FD G H
8 BA
Controls and functions
5 En
English
INTRODUCTION
C PHONES jack
Outputs audio to your headphones for private
listening.
D SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the
rear panel each time the corresponding button is
pressed.
E USB jack
For connecting a USB storage device (p. 41).
F BASS +/–
Increases or decreases the low frequency response.
Control range: –10 to +10 (20 Hz)
G TREBLE +/–
Increases or decreases the high frequency response.
Control range: –10 to +10 (20 kHz)
H INPUT l / h
Selects the input source you want to listen to.
I SELECT/ENTER (jog dial)
Turn the dial to select a numeric value or setting, and
press the dial to confirm.
J RETURN
Returns to the previous indication of the front display.
CONNECT
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices.
See MusicCast Setup Guide for details.
K VOLUME control
Increases or decreases the sound output level.
Controls and functions
6 En
[AM radio is available only for R-N402.]
y
You can change the brightness level of the front display by pressing DIMMER (p. 8).
1 Information display
Displays the current status (such as input name).
You can switch the information that is displayed when
you press DISPLAY (p. 20).
2 STEREO
Lights up when the unit is receiving a stereo FM radio
signal.
3 TUNED
Lights up when the unit is receiving an FM/AM radio
station signal.
4 Speaker indicators
“SP A” lights up when the SPEAKERS A output is
enabled and “SP B” lights up when the SPEAKERS B
output is enabled.
5 MUTE
Blinks when audio is muted.
6 SLEEP
Lights up when the sleep timer is on (p. 21).
Front display
STEREO SP
MUTE
A
TUNED
SP
SLEEP
B
1
42 3 5 6
Controls and functions
7 En
English
INTRODUCTION
[AM radio is available only for R-N402.]
1 NETWORK jack
For connecting to a network with a network cable
(p. 13).
2 ANTENNA terminals
For connecting to the radio antennas (p. 12).
3 Wireless antenna
For connecting to a network device wirelessly (p. 13).
4 Power cable
For connecting to an AC wall outlet (p. 13).
5 OPTICAL jack
For connecting to audio components equipped with
optical digital output (p. 10).
6 COAXIAL jack
For connecting to audio components equipped with a
coaxial digital output (p. 10).
7 CD jacks
For connecting to a CD player (p. 10).
8 LINE 1-3 jacks
For connecting to analog audio components (p. 10).
9 SPEAKERS terminals
Used to connect speakers (p. 11).
0 VOLTAGE SELECTOR
(Only for General and Brazil models)
Rear panel
MAINS
VOLTAGE SELECTOR
SPEAKERS
WIRELESS
ANTENNA
CD LINE
IN
OUT
A
B
22020
240 V
0
NETWORK
DIGITAL
OPTICAL
COAXIAL
AM
FM
75
23
65 78 9
0
12 3
4
(R-N402)
Controls and functions
8 En
1 Infrared signal transmitter
Sends infrared signals.
2 A (power)
Turns on/off (standby) the unit.
3 SLEEP
Sets the sleep timer (p. 21).
4 DIMMER
Changes the brightness level of the front display.
Choose brightness from 5 levels by pressing this key
repeatedly.
5 SPEAKERS A/B
Turns on and off the set of speakers connected to the
SPEAKERS A and/or SPEAKERS B terminals on the
rear panel of this unit when the corresponding key is
pressed.
6 Input selection keys
Select the input source you want to listen to.
y
NET key is for network source. Press repeatedly to select a
desired network source.
7 MODE
Sets the FM band reception mode to automatic stereo
or monaural (p. 22, 26).
8 MEMORY
Registers the current radio station as a preset when
TUNER is selected as the input source (p. 23, 27, 31).
Registers the current playback song or streaming
station as a preset when NET, USB are selected as the
input source (p. 43).
9 PRESET j / i
Recalls a preset radio station (p. 24, 28, 31) or song/
streaming station (p. 43).
0 Menu operation keys
Cursor keys Select a menu or a parameter.
ENTER Confirms a selected item.
RETURN Returns to the previous state.
A HOME
Moves up top level when selecting music files,
folders, etc.
B SETUP
Displays the “SETUP” menu (p. 45).
C NOW PLAYING
Displays music information when selecting music
files, folders, etc.
D Playback keys
Let you play back and perform other operations for
network sources, Bluetooth devices and USB devices.
Yamaha does not guarantee the operation of all Bluetooth and
USB devices.
Remote control
LINE 1
CD
NET USB
BLUETOOTH
TUNER
TUNING
PRESET
MUTE
NOW PLAYING
RETURN
OPTION
VOLUME
MEMORY
MODE
BAND
DISPLAY
LINE 2 LINE 3
ENTER
DIMMER
SLEEP
SPEAKERS
COAXIAL
OPTICAL
BA
HOME
SETUP
REPEAT
SHUFFLE
1
2
3
4
A
B
G
H
C
I
5
7
8
9
D
0
E
F
6
Note
Controls and functions
9 En
English
INTRODUCTION
E DISPLAY
Selects the information displayed on the front display
(p. 20).
F Radio keys
Operate the radio.
BAND Sets the radio tuner band when
TUNER is selected as the input
source (p. 22, 26, 30).
TUNING jj / ii Selects the tuning frequency
(p. 22, 26) or a DAB radio station
(p. 30) when TUNER is selected
as the input source.
G OPTION
Displays the “OPTION” menu (p. 44).
H MUTE
Mutes the audio output.
I VOLUME +/
Increases or decreases the sound output level.
Installing batteries
Change all batteries if you notice the operation range of
the remote control narrows. Before inserting new
batteries, wipe the battery compartment clean.
Operation range
Point the remote control at the remote control sensor on
this unit and remain within the operating range shown
below. The area between the remote control and this unit
must be clear of large obstacles.
Be careful not to drop the remote control.
If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.
If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material
comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery
compartment thoroughly before installing new batteries.
Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.
Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a
different specification.
Dispose of batteries according to your regional regulations.
Keep the batteries in a location out of reach of children.
Batteries can be dangerous if a child were to put in his or her mouth.
If you plan not to use this unit for a long period of time, remove the batteries from this unit. Otherwise, the batteries will wear out,
possibly resulting in a leakage of battery liquid that may damage this unit.
AA, R6, UM-3 batteries
Approximately
6 m (20 ft)
Remote control
CAUTION
10 En
PREPARATION
Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will
be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and
lack bass. Refer to the owner’s manual for each of your components.
Make sure to use RCA cables to connect audio components.
Do not connect this unit or other components to the main power until all connections between components are
complete.
Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the
speakers.
Do not bundle audio cables and speaker cables together with the power cable. Doing so may generate noise.
Connections
CAUTION
Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.
SPEAKERS
WIRELESS
ANTENNA
CD LINE
IN
OUT
AM
FM
75
A
B
NETWORK
DIGITAL
OPTICAL
COAXIAL
23
OC
Audio
input
Audio
output
Speakers B
DVD player, etc.
Audio output
(digital coaxial)
Audio output
(digital optical)
CD player, etc.
Audio
output
CD player
CD recorder, etc.
Speakers A
(R-N402)
Note
11 En
Connections
English
PREPARATION
Connecting speaker cables
aRemove approximately 10 mm (3/8") of insulation
from the ends of the speaker cable and twist the bare
wires of the cable firmly together.
bLoosen the speaker terminal.
cInsert the bare wires of the cable into the gap on the
side (upper right or bottom left) of the terminal.
dTighten the terminal.
Connecting via banana plug
(North America, Australia, Brazil,
General models only)
Tighten the knob and then insert the banana plug into the
end of the corresponding terminal.
When inserting speaker cables into the speaker terminals, insert
only the bare speaker wire. If insulated cable is inserted, the
connection may be poor and sound may not be heard.
Connect the speakers with an impedance as shown below.
If you connect speakers with an excessively low
impedance, this unit may overheat.
Bi-wire connection
Bi-wire connection separates the woofer from the
combined midrange and tweeter section. A bi-wire
compatible speaker has four binding post terminals. These
two sets of terminals allow the speaker to be split into two
independent sections. With these connections, the mid and
high frequency drivers are connected to one set of terminals
and the low frequency driver to another set of terminals.
Connect the other speaker to the other set of terminals in
the same way.
When making bi-wire connections, remove the shorting bridges
or cables on the speaker. Refer to the speakers’ instruction
manuals for more information.
y
To use the bi-wire connections, press SPEAKERS A and
SPEAKERS B (p. 8) so that both speaker indicators (“SP A” and
“SP B”) light up on the front display.
Connecting the speakers
Note
CAUTION
Speaker connection Speaker impedance
SPEAKERS A or
SPEAKERS B
8 or higher
SPEAKERS A and
SPEAKERS B
16 or higher
(except for North America model)
Bi-wiring 8 or higher
10 mm
(3/8")
Red:positive (+)
Black:negative (–)
Banana plug
Note
A
B
SPEAK
This unit
Speaker
12 En
Connections
Connect the supplied FM/AM antenna to this unit.
Fix the end of the FM antenna to a wall, and place the AM
antenna.
If you experience poor reception quality, install an outdoor
antenna.
Unwind only the length of cable needed from the AM antenna
unit.
The wires of the AM antenna have no polarity.
Assembling the supplied AM antenna
Connecting the wires of the AM antenna
Connect the supplied DAB/FM antenna to this unit and fix
the antenna ends to a wall.
If you experience poor reception quality, install an outdoor
antenna.
The antenna should be stretched out horizontally.
Connecting the FM/AM antennas
(R-N402)
Notes
ANTENNA
CD LINE
IN
OUT
NETWORK
DIGITAL
OPTICAL
COAXIAL
AM
FM
75
FM antenna AM antenna
Insert
2
Hold down
1
Connecting the DAB/FM antenna
(R-N402D)
Notes
CD LINE
IN
OUT
NETWORK
DIGITAL
OPTICAL
COAXIAL
ANTENNA
FMDAB
75
DAB/FM antenna
13 En
Connections
English
PREPARATION
Connect the unit to your router with a commercially-
available STP network cable (CAT-5 or higher straight
cable).
If you connect the unit wirelessly, erect the wireless
antenna. For information on how to connect the unit to a
wireless network, see “Connecting to network” (p. 14).
Do not apply excessive force on the wireless antenna. Doing so
may damage the antenna.
Plug the power cable into an AC wall outlet after all other
connections are complete.
Only for General and Brazil models:
Before connecting the power cable, make sure you set
VOLTAGE SELECTOR of this unit according to your
local voltage. Improper setting of VOLTAGE SELECTOR
may cause fire and damage to this unit.
Press A (power) to turn on the unit.
Connecting the network cable
Preparing a wireless antenna
Note
ANTENNA
CD LINE
DIGITAL
OPTICAL
AM
FM
75
NETWORK
LAN
WAN
Network Attached
Storage
(NAS)
Internet
Modem
Router
Network cable
PC
This unit (rear)
Mobile device
(such as iPhone)
WIRELESS
WORK
Connecting power cable
CAUTION
Turning on the unit
MAINS
VOLTAGE SELECTOR
22020
240 V
0
VOLTAGE SELECTOR
22020
240 V
0
To the AC wall outlet
with the power cable
LINE 1
CD
NET USB
BLUETOOTH
TUNER
TUNING
PRESET
MEMORY
MODE
BAND
DISPLAY
LINE 2 LINE 3
DIMMER
SLEEP
SPEAKERS
COAXIAL
OPTICAL
BA
A
(power)
14 En
There are several methods to connect the unit to a network. Select a connection method according to your environment.
Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the
unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.
Each server must be connected to the same subnet as the unit.
To use the service via the Internet, broadband connection is strongly recommended.
When playing a high-resolution audio source via the network, we recommend connecting by cable to the router for stable playback.
Connecting with the MusicCast CONTROLLER app
See MusicCast Setup Guide for details.
Connecting with a wireless router (access point)
Connect to the network with the method listed below that corresponds to your environment.
Connecting to a router using a cable
For information on how to set the IP address and other menu items, please refer to page 46.
To switch from a wireless LAN connection to a wired LAN connection, set the “Connection” under the
“Network” setup menu to “Wired” (p. 46).
Connecting without a wired router or wireless router (access point)
When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play
back contents from the Internet, connect this unit to a network with a wired router or wireless router (access point).
Connecting to a network
Notes
WAC (Wireless Accessory Configuration)
If you turn on the power to the unit right after you purchase or
initialize it, the unit will automatically use the network settings of the
iOS device (iPhone/iPad/iPod touch) and try to connect to a wireless
LAN (unless the unit is already connected to a wired LAN).
If you have an iOS device, follow the procedure from Step 6 in the section “Sharing the iOS device setting” (p. 15).
If you plan to connect the unit wirelessly by another method, press RETURN to exit the current screen, and then proceed to one of
the sections below.
Note
R-N402 XXXXXX
WAC
R-N402 (example)
Connecting using the Wi-Fi setting of the iOS
device (iPhone / iPad / iPod touch)
Share the Wi-Fi setting of the iOS
device (p. 15)
Connecting using WPS push button configuration
on the wireless router (or access point)
Use the WPS push button
configuration (p. 16)
Connecting with a wireless router (access point)
without WPS push button configuration
Set the network connection
manually (p. 17)
Connecting using the DHCP server function of the
router
You can connect to the network by
simply making a wired connection
(p. 13)
Connecting wirelessly to a mobile device
(Wireless Direct)
Connect wirelessly with Wireless
Direct (p. 18)
15 En
Connecting to a network
English
PREPARATION
You can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPad/iPod
touch).
Before proceeding, confirm that your iOS device is
connected to a wireless router (access point).
If you perform the following procedure, all network settings will be
initialized.
This configuration does not work if the security protocol of your
wireless router (access point) is WEP. In this case, use another
connection method.
1 Press SETUP.
2 Use the cursor keys ( / ) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
3 Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4 Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
5 Use the cursor keys ( / ) to select “Share
Setting” and then press ENTER twice.
6 On the iOS device, select the unit as the
AirPlay speaker in the Wi-Fi screen.
7 Check that the “Network” field is set to your
preferred network, and then tap “Next”.
When the sharing process finishes, the unit is
automatically connected to the selected network
(access point).
When the setting finishes, verify whether the unit is
connected to a wireless network (p. 19).
Sharing the iOS device setting
Notes
PRESET
MUTE
NOW PLAYING
RETURN
OPTION
VOLUME
MEMORY
ENTER
HOME
SETUP
RETURN
SETUP
ENTER
ENTER
Cursor keys
/
¡WPS
WIRELESS
The name of this unit
Example (iOS 9)
Tap here to start setup
The network currently
selected
16 En
Connecting to a network
You can easily set up a wireless connection with one push
of the WPS button.
This configuration does not work if the security method of your
wireless router (access point) is WEP. In this case, use another
connection method.
1 Press SETUP.
2 Use the cursor keys ( / ) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
3 Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4 Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
5 Press ENTER twice.
“Connecting” appears on the front display.
6 Push the WPS button on the wireless router
(access point).
When the connection process finishes, “Completed”
appears on the front display. When the setting
finishes, verify whether the unit is connected to a
wireless network (p. 19).
If “Not connected” appears, repeat from Step 1 or try
another connection method.
7 To exit from the menu, press SETUP.
Using the WPS push button
configuration
Note
PRESET
MUTE
NOW PLAYING
RETURN
OPTION
VOLUME
MEMORY
ENTER
HOME
SETUP
RETURN
SETUP
ENTER
ENTER
Cursor keys
/
¡WPS
WIRELESS
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
17 En
Connecting to a network
English
PREPARATION
Before performing the following procedure, check the
security method and security key on the wireless router
(access point).
1 Press SETUP.
2 Use the cursor keys ( / ) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
3 Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4 Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
5 Use the cursor keys ( / ) to select
“ManualSetting” and press ENTER.
6 Use the cursor keys ( / ) to select “SSID”
and press ENTER.
7 Use the cursor keys to enter the SSID on the
wireless router (access point), and press
RETURN to previous state.
Use the cursor keys (/) to select a character and
the cursor keys (/) to move the edit position.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
8 Use the cursor keys ( / ) to select
“Security” and press ENTER.
9 Use the cursor keys ( / ) to select desired
security method and press RETURN.
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
If you select “None”, the connection may be insecure since the
communication is not encrypted.
10 Use the cursor keys ( / ) to select
“Security Key” and press ENTER.
11 Use the cursor keys to enter the security key
on the wireless router (access point), and
press RETURN to previous state.
If you select “WEP” in Step 9, enter either 5 to 13
character string or 10 to 26 hexadecimal digits.
If you select “WPA2-PSK (AES)” or “Mixed Mode”
in Step 10, enter either 8 to 63 character string or 64
hexadecimal digits.
Use the remote control keys as described in Step 7 to
enter the key.
12 Use the cursor keys ( / ) to select
“Connect [ENT]” and press ENTER to save
the setting.
If “ERROR” appears, check the SSID and security
key on the wireless router (access point) and repeat
from Step 6.
If “ERROR” does not appear, the connection was
successful. Verify whether the unit is connected to a
wireless network (p. 19).
13 To exit from the menu, press SETUP.
Set the wireless network
connection manually
PRESET
MUTE
NOW PLAYING
RETURN
OPTION
VOLUME
MEMORY
ENTER
HOME
SETUP
ENTER
RETURN
SETUP
ENTER
Cursor keys
¡SSID
MANUAL
¡
SSID
Note
¡WPA2-PSK(AES)
SECURITY
KEY
18 En
Connecting to a network
Using Wireless Direct, this unit can operate as a wireless
network access point that mobile devices can directly
connect to.
When the unit is connected to the network with Wireless Direct, it
cannot connect to any other wireless router (access point). To
play back contents from the Internet, connect this unit to a
network with a wired router or wireless router (access point).
1 Press SETUP.
2 Use the cursor keys ( / ) to select
“Network” and press ENTER.
y
To return to the previous state, press RETURN.
3 Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4 Use the cursor keys ( / ) to select
“W.Direct” and press ENTER.
5 Press ENTER to display the SSID for this
unit, and press RETURN to previous state.
6 Use the cursor keys ( / ) to select
“Security” and press ENTER.
7 Use the cursor keys ( / ) to select desired
security method and press RETURN.
Settings
None, WPA2-PSK (AES)
If you select “None”, the connection may be insecure since the
communication is not encrypted.
8 Use the cursor keys ( / ) to select
“Security Key” and press ENTER.
9 Use the cursor keys to enter the security key
on this unit, and press RETURN to previous
state.
Enter either 8 to 63 character string or 64
hexadecimal digits.
Use the cursor keys (/) to select a character and
the cursor keys (/) to move the edit position.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
10 Use the cursor keys ( / ) to select
“Connect [ENT]” and press ENTER to save
the setting.
The SSID and security key information is required
for setup of a mobile device.
When you select the “SSID” in Step 5, you can
display the SSID configured for this unit. This SSID
can be changed by using cursor keys.
11 Configure the Wi-Fi settings of a mobile
device.
For details on settings of your mobile device, refer to
the instruction manual of the mobile device.
(1) Enable the Wi-Fi function on the mobile device.
(2) Select the SSID of this unit from the list of
available access points.
(3) When you are prompted for a password, enter the
security key displayed in Step 9.
If “ERROR” appears, check the security key on this
unit and repeat Step 11.
If “ERROR” does not appear, the connection was
successful. Verify whether the unit is connected to a
wireless network (p. 19).
12 To exit from the menu, press SETUP.
Connecting a mobile device to the
unit directly (Wireless Direct)
Note
PRESET
MUTE
NOW PLAYING
RETURN
OPTION
VOLUME
MEMORY
ENTER
HOME
SETUP
ENTER
RETURN
SETUP
ENTER
Cursor keys
¡SSID
W.DIRECT
¡WPA2-PSK(AES)
W.DIRECT
Note
KEY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488

Yamaha R-N402 Omistajan opas

Kategoria
Radios
Tyyppi
Omistajan opas