Philips GC9660/30 Ohjekirja

Kategoria
Steam ironing stations
Tyyppi
Ohjekirja
1
2
4
12
11
10
13
16
17
14
9
8
5
1918
6 7
3
15
GC9600
PerfectCare Elite Plus
4239 001 18751
EN User Manual 6
DA Brugervejledning 16
DE Bedienungsanleitung 27
ES Manual de usuario 38
FI Käyttöopas 49
FR Mode d’emploi 59
IT Manuale per l’utente 70
NL Gebruiksaanwijzing 81
NO Brukerhåndbok 92
PT Manual do utilizador 103
SV Användarhandbok 114
1
A
B
C
EN IMPORTANT: Perform descaling regularly for great steam
and prolonged life.
Let the appliance cool down completely, before you remove
the EASY DE-CALC KNOB.
DE WICHTIG: Entkalken Sie regelmäßig, um eine gute
Dampeistung und eine lange Nutzungsdauer zu
gewährleisten.
Drehen Sie den EASY DE-CALC-Verschluss nicht, während
das Gerät eingeschaltet ist, oder sofort nach der Nutzung.
FR IMPORTANT : eectuez régulièrement un détartrage pour une vapeur de
qualité et une durée de vie prolongée.
Ne retirez pas le bouton EASY DE-CALC lorsque l’appareil est allumé ou juste
après utilisation.
IT IMPORTANTE: eseguite regolarmente la procedura di decalcicazione per
avere maggiore vapore e maggiore durata del ferro.
Non aprire la manopola EASY DE-CALC quando il dispositivo è acceso o
subito dopo l’uso.
NL BELANGRIJK: regelmatig ontkalken zorgt voor goede stoom en een langere
levensduur.
Open de EASY DE-CALC-knop niet terwijl het apparaat ingeschakeld is of
direct nadat het is gebruikt.
ES IMPORTANTE: Elimine los depósitos de cal regularmente para mejorar a salida
de vapor y prolongar la vida útil.
Não abra o botão EASY DE-CALC quando o dispositivo está ligado ou
imediatamente após a utilização.
D
Welcome to the future!
Say hello to your new powerful smart friend and
learn how to use it in this booklet.
EN Intelligent automatic steam
Enabled by the DynamiQ sensor, steam is released
automatically when the iron is moved.
DE Intelligenter und automatischer Dampfst
Durch den DynamiQ Sensor aktiviert, wird automatisch
Dampf ausgestoßen, wenn das Bügeleisen bewegt wird.
FR Vapeur automatique intelligente
Grâce au capteur DynamiQ, de la vapeur est libérée
automatiquement lorsque vous déplacez le fer.
IT Vapore automatico intelligente
Il vapore viene attivato dal sensore DynamiQ e rilasciato
automaticamente quando si muove il ferro.
NL Intelligent automatisch stomen
Dankzij de DynamiQ-sensor komt er automatisch stoom
vrij wanneer het strijkijzer beweegt.
ES Vapor automático inteligente
Con el sensor DynamiQ, saldrá vapor automáticamente
cuando se mueve la plancha.
6 ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips! To fully
benet from the support that Philips oers, register your product at
www.philips.com/welcome.
Read the separate important information leaet and the user manual
carefully before you use the appliance. Save both documents for future
reference.
Product overview (Fig. 1)
1 Steam supply hose
2 Iron platform
3 First supply hose storage compartment
4 Mains cord with plug
5 ECO button with light
6 On/o button with light and MAX setting
7 ‘Water tank empty’ light
8 EASY DE-CALC light
9 EASY DE-CALC knob
10 Cord storage compartment
11 Second supply hose storage compartment
12 Detachable water tank
13 Carry lock
14 Carry lock release button
15 Soleplate
16 Steam trigger
17 ‘Iron ready’ light
18 Intelligent automatic steam button with light
19 Filling hole
Using your appliance
Type of water to use
This appliance has been designed to be used with tap water. However,
if you live in an area with hard water, fast scale build-up may occur.
Therefore, it is recommended to use distilled or demineralized water (50%
demineralized/distilled water mixed with water could be used as well) to
prolong the lifetime of the appliance.
Do not add perfume, water from the tumble dryer, vinegar, starch,
descaling agents, ironing aids, chemically descaled water or other
chemicals, as they may cause water spitting, brown staining or damage to
your appliance.
7
ENGLISH
Filling the water tank
Fill the water tank before every use or when the ‘water tank empty’ light
ashes. You can rell the water tank at any time during use.
1 Remove the water tank from the appliance and ll it with tap water up
to the MAX indication.
2 Put the water tank back into the appliance by tting the bottom part
into the appliance rst.
3 Push the top part until it locks into place.
‘Water tank empty’ light
When the water tank is almost empty, the ‘water tank empty’ light ashes.
Fill the water tank and press the steam trigger to let the appliance heat up
again. When the ‘iron ready’ light lights up continuously, you can continue
steam ironing.
OptimalTEMP technology
The OptimalTEMP technology enables you to iron all types of ironable
fabrics, in any order, without adjusting the iron temperature setting.
Fabrics with these symbols are ironable, for example linen, cotton,
polyester, silk, wool, viscose and rayon.
Fabrics with this symbol are not ironable. These fabrics include synthetic
fabrics such as Spandex or elastane, Spandex-mixed fabrics and
polyolens (e.g. polypropylene), but also prints on garments.
8
ENGLISH
During ironing, you can place the iron either on the iron platform or
horizontally on the ironing board. Thanks to the OptimalTEMP technology,
the soleplate will not damage the ironing board cover.
Ironing
1 Place the steam generator on a stable and even surface.
2 Make sure that there is enough water in the water tank (see section
‘Filling the water tank’).
3 Put the mains plug in an earthed wall socket and press the on/o
button to switch on the steam generator. The blue power-on light on
the appliance and the ‘iron ready’ light start to ash to indicate that
the appliance is heating up (this takes approx. 2 minutes).
, When the appliance is ready for use, the ‘iron ready light’ and the
power-on light stop ashing and light up continuously. Additionally
you hear a short beep.
4 Press the carry lock release button to unlock the iron from the iron
platform.
5 Press and hold the steam trigger to start ironing.
Never direct steam at people.
Note: For best result on tough fabrics such as cotton, linen and jeans,
keep the steam trigger pressed continuously when you move the iron
over the fabric. Then move the iron over the same area a few more times
without steam to dry the fabric.
Note: For the best results on silk and shiny synthetic fabrics, it is
recommended to keep the steam trigger pressed continuously while
ironing.
sensor and intelligent automatic steam mode
The intelligent sensor inside your iron knows exactly when and
how your iron is moving. When you activate intelligent automatic steam
mode, the sensor will start recognizing the movements of
your iron and will enable your iron to release the right amount of steam
9
ENGLISH
automatically without you having to press the steam trigger. This will help
you to get great results faster and easier.
- To activate the intelligent automatic steam mode, press the intelligent
automatic steam button on top of the iron handle. The intelligent
automatic steam light turns on.
- The ‘iron ready’ light moves back and forth when the iron is moving.
Note: in intelligent automatic steam mode, steam comes out
automatically when you move the iron and stops when you stop moving
the iron. You can still press the steam trigger in this mode to activate the
steam when the iron is not moving.
- You can use the intelligent automatic steam mode in all steam settings,
including ECO and MAX.
Note: for your safety, in intelligent automatic steam mode, the steam
stops when the soleplate is tilted.
- To exit the intelligent automatic steam mode, press the intelligent
automatic steam button. The intelligent automatic steam light turns
o. You need to press the steam trigger to continue your ironing.
Steam boost function
The steam boost function is designed to help tackle dicult creases.
- Press the steam trigger twice quickly to activate the steam boost
function. The appliance releases 3 powerful shots of steam.
Vertical ironing
Hot steam is emitted from the iron. Never attempt to remove creases
from a garment that someone is wearing. Do not apply steam near your or
someone else’s hand.
You can use the iron in vertical position to remove wrinkles from hanging
fabrics.
1 Hold the iron in vertical position, press the steam trigger and touch
the garment slightly with the soleplate.
Note: for your safety, the intelligent automatic steam mode is not
available for vertical ironing.
2x
10
ENGLISH
ECO setting
By using the ECO setting (reduced amount of steam), you can save energy
without compromising on the ironing result.
- Press the ECO button. The green ECO light turns on.
- To deactivate ECO setting, press then ECO button again. The green
ECO light goes o.
MAX setting
For faster ironing and a higher amount of steam, you can use MAX setting.
1 Press and hold the on/o button for 2 seconds until the light turns
white.
2 To deactivate MAX setting, press and hold the on/o button again for
2 seconds until the white light turns blue
Auto shut-o
- The appliances enters the standby mode if it has not been used for 10
minutes. The light in the on/ o button starts to ash.
- To activate the appliance again, press the on/o button. The appliance
starts to heat up again.
- The appliance switches o automatically if it has not been used for
another 10 minutes after it enters the standby mode. The light in the
on/o button goes o.
Ironing tips
Minimising wrinkles while drying
Start wrinkle removal early in the drying process by spreading out your
laundry properly after washing and by putting garments on hangers to
make them dry naturally with fewer wrinkles.
Best practice shirt ironing
Start with the time-consuming parts like collar, cu links and sleeves. Next,
iron the bigger parts like front and back to prevent wrinkling the bigger
parts when you are busy ironing the time-consuming parts.
2 sec.
11
ENGLISH
Collar: When you iron a collar, start on its underside and work from the
outside (the pointy end) inwards. Turn over and repeat. Fold down the
collar and press the edge for a more crisp nish.
Buttons: Iron on the reverse side of the buttons for more eective and
faster ironing.
Cleaning and maintenance
To properly maintain your appliance, clean the iron and the appliance
regularly.
1 Clean the appliance with a moist cloth. To remove stubborn stains,
you can use a small amount of washing-up liquid.
2 To easily and eectively remove stains from the soleplate, switch on
the appliance and let it heat up. When the appliance has heated up,
move the iron over a moist cloth while you press the steam trigger.
Tip: Clean the soleplate regularly to ensure smooth gliding.
IMPORTANT - EASY DE-CALC
It is very important to use the EASY DE-CALC function as soon as
the EASY DE-CALC light starts to ash and the appliance beeps
continuously.
The EASY DE-CALC light ashes and the appliance beeps continuously
after about a month or 10 ironing sessions to indicate that the appliance
needs to be descaled. Perform the following EASY DE-CALC procedure
before you continue ironing.
To avoid the risk of burns, unplug the appliance and let it cool down for
at least two hours before you perform the EASY DE-CALC procedure.
1 Remove the plug from the wall socket.
2 Place the appliance on the edge of the tabletop.
3 Hold a cup (with a capacity of at least 350ml) under the EASY DE-
CALC knob and turn the knob anticlockwise.
12
ENGLISH
4 Remove the EASY DE-CALC knob and let the water with scale
particles ow into the cup.
5 When no more water comes out of the appliance, reinsert the EASY
DE-CALC knob and turn it clockwise to fasten it.
6 You can continue using your iron immediately after completing the
EASY DE-CALC procedure.
IMPORTANT – Descaling the soleplate
If you do not use the EASY DE-CALC function regularly, scale particles
may build up in the soleplate and brown stains may come out of the
soleplate during ironing. In this situation, you need to descale the
soleplate by following the procedure below. We advice you to repeat the
procedure twice to better clean the soleplate.
To avoid the risk of burns, unplug the appliance and let it cool down for at
least two hours before you descale the soleplate.
1 Remove the plug from the wall socket.
2 Place the appliance on the edge of the tabletop.
3 Make sure that the water tank is empty.
4 Hold a cup (with a capacity of at least 350ml) under the EASY DE-
CALC knob and turn the knob anticlockwise.
13
ENGLISH
5 Remove the EASY DE-CALC knob and let the water with scale
particles ow into the cup.
6 Hold the appliance in the position that EASY DE-CALC opening is
facing up and pour 900ml distilled water into the opening.
Note: Be mindful on the heavy weight of the appliance when you tilt it.
7 Keep the EASY DE-CALC opening facing up, reinsert the EASY DE-
CALC knob and turn it clockwise to fasten it.
8 Put the appliance back on a stable and even surface. Plug in the
appliance and switch it on.
9 Wait for 5 minutes for the appliance to heat up.
10 Keep the steam trigger pressed continuously while you move the iron
on a piece of thick cloth for 3 minutes.
Warning: hot, dirty water comes out of the soleplate.
11 Stop moving the iron when no more water comes out or when steam
starts coming out.
12 You can continue to use the appliance immediately. Otherwise unplug
the appliance after the descaling is completed.
14
ENGLISH
Storage
1 Switch o the appliance and unplug it.
2 Remove the water tank and empty it.
3 Put the iron on the iron platform. Push the carry lock to lock the iron
onto the platform.
4 Fold the supply hose and mains cord. Put them in their respective
storage compartments.
5 You can carry the appliance with one hand by the handle of the iron.
Do not carry the appliance by holding the water tank release lever.
Troubleshooting
This chapter summarises the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Centre in your country.
Problem Possible cause Solution
The ironing board
cover becomes
wet or there are
water droplets on
the garment during
ironing.
Steam has condensed on the
ironing board cover after a long
ironing session.
Replace the ironing board cover if the foam
material has worn out. You can also add an
extra layer of felt material under the ironing
board cover to prevent condensation on the
ironing board. You can buy felt in a fabric
shop.
You have an ironing board cover
that is not designed to cope
with the high steam rate of the
appliance.
Put an extra layer of felt material under the
ironing board cover to prevent condensation
on the ironing board. You can buy felt in a
fabric shop.
Water droplets come
out of the soleplate.
The steam that was still present
in the hose has cooled down
and condensed into water. This
causes water droplets to come
out of the soleplate.
Steam away from the garment for a few
seconds.
15
ENGLISH
Problem Possible cause Solution
Steam and/or water
come out from under
the EASY DE-CALC
knob.
The EASY DE-CALC knob is not
tightened properly.
Switch o the appliance and let the
appliance cool down for 2 hours. Unscrew
the EASY DE-CALC knob and screw it back
onto the appliance properly. Note: Some
water may escape when you remove the
knob.
The rubber sealing ring of the
EASY DE-CALC knob is worn.
Contact an authorised Philips service centre
for a new EASY DE-CALC knob.
Dirty water and
impurities come out
of the soleplate or
the soleplate is dirty.
Impurities or chemicals present
in the water have deposited in
the steam vents and/or on the
soleplate.
Clean the soleplate with a damp cloth.
Too much scale and minerals
have accumulated inside the
appliance.
Descale the appliance regularly (see chapter
‘Important - DESCALING’).
The iron leaves a
shine or an imprint
on the garment.
The surface to be ironed was
uneven, for instance because you
were ironing over a seam or a fold
in the garment.
PerfectCare is safe on all garments. The
shine or imprint is not permanent and will
come o if you wash the garment. Avoid
ironing over seams or folds or you can place
a cotton cloth over the area to be ironed to
avoid imprints at seams and folds.
The appliance does
not produce any
steam.
There is not enough water in the
water tank (the ‘water tank empty’
light ashes).
Fill the water tank (see chapter ‘Using your
appliance, section ‘Filling the water tank’).
The appliance is not hot enough
to produce steam.
Wait until the ‘iron ready’ light on the iron
lights up continuously.
You did not press the steam
trigger.
Press the steam trigger and keep it pressed
while you iron.
The water tank is not placed in
the appliance properly.
Slide the water tank back into the appliance
rmly (‘click’).
The appliance is not switched on. Insert the plug in the wall socket and
press the on/o button to switch on the
appliance.
The appliance has
switched o. The
light in the on/o
button ashes.
The auto-o function is activated
automatically when the appliance
has not been used for more than
10 minutes.
Press the power on/o button to switch on
the appliance again.
The appliance
produces a pumping
sound.
Water is pumped into the boiler
inside the appliance. This is
normal.
If the pumping sound continues nonstop,
switch o the appliance and remove the
plug from the wall socket. Contact an
authorised Philips service centre.
16
DANSK
Introduktion
Tillykke med dit køb og velkommen til Philips! Få alle fordele af
den support, som Philips tilbyder, ved at registrere dit produkt på
www.philips.com/welcome.
Læs den separate folder med vigtige oplysninger og brugervejledningen
omhyggeligt igennem, før du tager apparatet i brug. Gem begge
dokumenter til eventuel senere brug.
Produktoversigt (Fig. 1)
1 Dampslange
2 Holder til strygejern
3 Opbevaringsrum til forsyningsslange
4 Netledning med stik
5 ECO-knap med lys
6 On/o-knap med lys og MAX-indstilling
7 Lysindikator for "tom vandtank"
8 EASY DE-CALC-indikator
9 EASY DE-CALC-knap
10 Rum til at opbevare ledningen
11 Andet opbevaringsrum til forsyningsslange
12 Aftagelig vandtank
13 Transportlås
14 Udløserknap til transportlås
15 Strygesål
16 Dampudløser
17 Lysindikator for "strygejernet er klar"
18 Intelligent automatisk dampknap med lys
19 Påfyldningshul
Sådan bruges apparatet
Type af vand, der skal bruges
Der skal kommes vand fra hanen i apparatet. Hvis du bor i et område med
hårdt vand, kan der dog hurtigt komme kalkaejringer. Derfor anbefales
det at bruge destilleret eller demineraliseret vand (50% demineraliseret/
destilleret vand blandet op med vand kan også anvendes), så apparatets
levetid forlænges.
Tilsæt ikke parfume, vand fra en tørretumbler, eddike, stivelse,
afkalkningsmiddel, strygemiddel, kemisk afkalket vand eller andre
kemikalier, da de kan medføre vandstænk, brune pletter eller skader på
apparatet.
17
DANSK
Påfyldning af vandtanken
Fyld vandtanken før hver brug, eller når indikatoren ”tom vandtank” lyser.
Vandtanken kan påfyldes når som helst under brug.
1 Tag vandtanken ud, skyl og fyld den med friskt vand op til MAX-
markeringen.
2 Sæt vandtanken tilbage i apparatet, så den nederste del kommer ned
i apparatet først.
3 Skub den øverste del af vandtanken ind, indtil den låser på plads
(„klik“).
Lysindikator for "tom vandtank"
Når vandtanken er ved at være tom, lyser indikatoren for "tom vandtank".
Fyld vandtanken, og tryk på dampudløseren for at lade apparatet varme
op igen. Når lysindikatoren for "strygejernet er klar" lyser konstant, kan du
fortsætte med dampstrygningen.
OptimalTEMP-teknologi
OptimalTemp-teknologien gør det muligt at stryge alle strygbare tekstiler, i
vilkårlig rækkefølge, uden at justere strygetemperaturen.
Materialer med disse symboler er strygbare, f.eks. linned, bomuld,
polyester, silke, uld, viskose og rayon.
Materialer med dette symbol kan ikke stryges. Disse materialer omfatter
syntetiske stoer som f.eks. spandex eller elastan, stoer med spandex-
blandinger og polyolener (f.eks. polypropylen) samt tøj med påtrykt
mønster.
18
DANSK
Under strygningen kan du enten stille strygejernet i holderen eller i vandret
position på strygebrættet. OptimalTEMP-teknologien sikrer, at strygesålen
ikke skader beklædningen på strygebrættet.
Strygning
1 Stil dampgeneratoren på et stabilt og jævnt underlag.
2 Kontroller, at der er nok vand i vandtanken (se afsnittet "Påfyldning af
vandtanken").
3 Sæt netstikket i en jordforbundet stikkontakt, og tryk på tænd/sluk-
knappen for at tænde for dampgeneratoren. Den blå kontrollampe
på apparatet og lysindikatoren for "strygejernet er klar" begynder at
blinke for at indikere, at apparatet varmer op (det tager ca. 2 minutter).
, Når apparatet er klar til brug, holder lysindikatoren "strygejernet er
klar" og kontrollampen op med at blinke og lyser konstant. Desuden
kan du høre et kort bip.
4 Tryk på udløserknappen til transportlåsen for at frigøre strygejernet
fra holderen.
5 Hold dampudløseren nede for at begynde strygning.
Ret aldrig dampstrålen mod personer.
Bemærk: For at opnå det bedste strygeresultat på stof såsom bomuld,
linned og jeans skal du holde dampudløseren nede konstant, når du
bevæger strygejernet over stoet. Bevæg derefter strygejernet over
samme område et par gange mere uden damp for at tørre stoet.
Bemærk: For at opnå det bedste strygeresultat på silke og skinnende,
syntetiske tekstiler anbefales det at holde dampudløseren nede konstant
under strygningen.
Sensor og intelligent automatisk damptilstand
Den intelligente sensor inde i dit strygejern ved præcis, hvornår
og hvordan dit strygejern er i bevægelse. Når du aktiverer intelligent
automatisk damptilstand, vil sensoren begynde at genkende
dit strygejerns bevægelser og gøre dit strygejern i stand til at frigøre den
rette mængde damp automatisk, uden at du skal trykke på dampudløseren.
19
DANSK
Dette vil hjælpe dig med at opnå fantastiske strygeresultater hurtigere og
nemmere.
- For at aktivere intelligent automatisk damptilstand skal du trykke
på knappen for intelligent automatisk damp øverst på strygejernets
håndtag. Indikatoren for intelligent automatisk damp tændes.
- Lysindikatoren for "strygejernet er klar" bevæger sig frem og tilbage,
når strygejernet er i bevægelse.
Bemærk: I intelligent automatisk damptilstand kommer der damp ud
automatisk, når du bevæger strygejernet, og den stopper, når du holder
op med at bevæge strygejernet. Du kan stadig trykke på dampudløseren i
denne tilstand for at aktivere damp, når strygejernet ikke er i bevægelse.
- Du kan bruge intelligent automatisk damptilstand i alle indstillinger,
herunder ECO og MAX.
Bemærk: Af sikkerhedsmæssige årsager stopper dampen, når strygesålen
står skråt i intelligent automatisk damptilstand.
- For at afslutte intelligent automatisk damptilstand skal du trykke på
knappen for intelligent automatisk damp. Indikatoren for intelligent
automatisk damp slukkes. Du skal trykke på dampudløseren for at
fortsætte strygningen.
Dampskudsfunktion
Dampskudsfunktionen er udviklet til at hjælpe med at klare vanskelige
folder.
- Tryk på dampudløseren to gange hurtigt efter hinanden for at aktivere
dampskudsfunktionen. Apparatet udsender 3 kraftige skud damp.
Lodret strygning
Strygejernet udsender varm damp. Du må aldrig forsøge at fjerne folder
fra tøj, som nogen har på. Anvend ikke damp i nærheden af din egen eller
en anden persons hånd.
Du kan bruge dampstrygejernet i lodret position til at fjerne folder fra
ophængte tekstiler.
2x2x
20
DANSK
1 Hold strygejernet lodret, tryk på dampudløseren, og berør forsigtigt
tekstilet med strygesålen.
Bemærk: Af hensyn til din sikkerhed er intelligent automatisk
damptilstand ikke tilgængelig ved lodret strygning.
ECO-indstilling
Ved hjælp af ECO-indstillingen (nedsat mængde damp) kan du spare
energi, uden at det går ud over strygeresultatet.
- Tryk på ECO-knappen. Den grønne ECO-indikator tændes.
- For at deaktivere ECO-indstilling skal du trykke på ECO-knappen igen.
Den grønne ECO-indikator slukkes.
MAX-indstilling
For hurtigere strygning og en højere mængde damp kan du bruge MAX-
indstillingen.
1 Hold on/o-knappen nede i 2 sekunder, indtil lysindikatoren lyser
hvidt.
2 For at deaktivere MAX-indstillingen skal du igen holde on/o-
knappen nede i 2 sekunder, indtil den hvide indikator skifter til blå
Auto-sluk
- Apparatet går i standbytilstand, hvis det ikke har været i brug i 10
minutter. Lysindikatoren i on/o-knappen begynder at blinke.
- Tryk på on/o-knappen for at aktivere apparatet igen. Apparatet
begynder nu at varme op igen.
- Apparatet slukker automatisk, hvis det ikke har været i brug i 10
minutter, efter det er gået i standbytilstand. Lysindikatoren i on/o-
knappen slukkes.
2 sec.
21
DANSK
Strygetip
Minimering af folder under tørringen
Start udglatning af folder i begyndelsen af tørringen ved at sprede dit
tøj grundigt ud efter vask og ved at hænge tøjet på bøjler, så det tørrer
naturligt med færre folder.
Fremgangsmåde for skjortestrygning
Begynd med de tidskrævende dele, f.eks. krave, manchetter og ærmer.
Stryg derefter de store dele som bryst og ryg. På denne måde undgår du, at
de større dele krøller, mens du stryger de tidskrævende dele.
Krave: Når du stryger en krave, skal du starte fra undersiden og arbejde
dig indad (fra den spidse ende). Vend kraven, og gentag proceduren. Fold
kraven ned, og pres kanten for et mere skarpt resultat.
Knapper: Stryg på modsatte side af knapperne for en mere eektiv og
hurtigere strygning.
Rengøring og vedligeholdelse
Korrekt vedligeholdelse af dit apparat kræver, at du rengør strygejernet og
apparatet regelmæssigt.
1 Tør apparatet af med en fugtig klud. Du kan fjerne genstridige pletter
ved at bruge en lille smule opvaskemiddel.
2 Du kan nemt og eektivt fjerne pletter fra strygesålen ved at tænde
for apparatet og lade det varme op. Når apparatet er varmet op,
skal du bevæge strygejernet over en fugtig klud, mens du trykker på
dampudløseren.
Tip: Rengør strygesålen regelmæssigt for at sikre, at den glider let.
VIGTIGT - EASY DE-CALC
Det er yderst vigtigt at foretage afkalkningsproceduren, så snart EASY
DE-CALC-lampen begynder at blinke, og apparatet bipper konstant.
Når der er gået ca. en måned, eller der er foretaget 10 strygninger, blinker
EASY DE-CALC-indikatoren, og apparatet bipper konstant for at indikere, at
apparatet skal afkalkes. Udfør følgende EASY DE-CALC-procedure, før du
fortsætter med at stryge.
Du skal tage apparatet ud af stikkontakten og lade det køle af i mindst
to timer, før du foretager EASY DE-CALC-proceduren, for at undgå risiko
for forbrænding.
1 Tag stikket ud af stikkontakten.
22
DANSK
2 Placer apparatet på kanten af bordpladen.
3 Hold en beholder (med en kapacitet på mindst 350 ml) under EASY
DE-CALC-knappen, og drej knappen mod uret.
4 Fjern EASY DE-CALC-knappen, og lad vandet med kalkpartikler yde
ned i koppen.
5 Når der ikke kommer mere vand ud af dampgeneratoren, skal du
påsætte EASY DE-CALC-knappen igen og dreje den med uret for at
stramme den.
6 Du kan fortsætte med at bruge dit strygejern umiddelbart efter, du
har udført EASY DE-CALC-proceduren.
VIGTIGTAfkalkning af strygesålen
Hvis du ikke bruger EASY DE-CALC-funktionen regelmæssigt, kan der
ophobe sig kalkpartikler i strygesålen, og der kan komme brune pletter
ud fra strygesålen under strygningen. I denne situation skal du afkalke
strygesålen ved at følge nedenstående fremgangsmåde. Det anbefales
at gentage proceduren to gange for at opnå en bedre rengøring af
strygesålen.
Du skal tage apparatet ud af stikkontakten og lade det køle af i mindst to
timer, før du afkalker strygesålen, for at undgå risiko for forbrænding.
1 Tag stikket ud af stikkontakten.
2 Placer apparatet på kanten af bordpladen.
3 Sørg for, at vandtanken sidder korrekt.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122

Philips GC9660/30 Ohjekirja

Kategoria
Steam ironing stations
Tyyppi
Ohjekirja