Silvercrest SON 90 A1 Operating Instructions Manual

Tyyppi
Operating Instructions Manual
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: SON 90 A1-01/10-V4
Overlock Sewing Machine SON 90 A1
3
Overlock Sewing Machine
Operating instructions
Overlock-symaskin
Bruksanvisning
Saumuri
Käyttöohje
Overlock-Nähmaschine
Bedienungsanleitung
CY
Ραπτομηχανή-Overlock
Οδηγίες χρήσης
CY
Opletilni (overlock)
šivalni stroj
Navodila za uporabo
SON 90 A1
1
3
4
5
6
7
8
9
0
q
uztr
e
w
p
o
i
a
s
d
f
2
- 1 -
INDEX PAGE
Intended Usage 3
Safety instructions 3
Items supplied 4
Technical Data 4
Description of the appliance 5
Bringing the upper blade into a rest position 5
Needle Information 5
Upper looper element 5
Opening the front flap 6
Preparation 6
Connecting the foot pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Controlling the sewing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Safety switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Fitting the waste container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Removing needle(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Inserting needle(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operating the handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Adjusting the thread tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Threading 8
General instructions for threading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Threading the upper looper thread (red) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Threading the lower looper thread (yellow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Threading yarn for the right needle (green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Threading yarn for the left needle (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Trial run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Changing threads (binding together) 15
Set the stitch length 15
Setting the seam width 15
... by using the right or left needle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
... by turning the seam width adjustment knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Setting the seam width adjustment knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Adjust sewing foot pressure 16
Differential transport 17
Manner of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Gathered overlock seam - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Stretched overlock seam - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Free arm sewing 18
Read these operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference. Pass this booklet on to
whoever might acquire the appliance at a future date.
- 2 -
Overlock seams 19
Roll hemmings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Binding-off and sample sewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Recommended tension settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2-thread overcast chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2-thread-overcast-stitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3-thread chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3 - thread - flatlock seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3-thread overcast chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
3-thread safety stitch, highly elastic, imitated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4-thread safety stitch, highly elastic, imitated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Roll hemmings 28
3-thread rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
3-thread upper looper overcast rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
2-thread rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2-thread lower looper overcast rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Flatlock decorative seams 30
Flatlock seam as assembly seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Flatlock seam as decorative seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Overlock blind hems 31
Pin tucks 31
Sewing corners 32
Outer corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Inner corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Tips and Tricks 33
Using pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Secure empty threads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Seam reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Edging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Maintenance and Cleaning 34
Cleaning and lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Exchanging the lower blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Storage 35
Disposal 35
Warranty and Service 35
Importer 35
Troubleshooting 36
- 3 -
Intended Usage
This overlock sewing machine is intended ...
- for use as a portable machine,
– for the trimming of material edges (sewing) of typical household
textiles, and ...
– only for domestic household use.
Safety instructions
Like any other electrical device, a sewing machine can cause serious, even
life-threatening injuries. To avoid these, and to work safely:
Always disconnect the power supply when leaving the machine unattended.
This will prevent the risk of accidents if the machine is switched on
accidentally.
Always first disconnect the power plug before carrying out maintenance
work on the machine. This will prevent possibly life-threatening electric
shocks. The LED light is not exchangeable.
Do not pull the plug out of the wall socket by the lead. When pulling
out the plug, always hold the plug, not the lead.
Only use the sewing machine in dry rooms.
Arrange for defective power plugs and/or cables to be replaced at
once by qualified technicians or our Customer Service Department.
This appliance is not intended for use by individuals (including children) with
restricted physical, physiological or intellectual abilities or deficiences in
experience and/or knowledge unless they are supervised by a person
responsible for their safety or receive from this person instruction in how
the appliance is to be used.
Children should be supervised to ensure that they do not play with
the appliance.
Never use the machine when the ventilation apertures are blocked.
Keep the ventilation apertures of the machine and the foot switch free
from fluff, dust and waste material.
Should the cable connected to the foot pedal become damaged,
to avoid potential risks it must be replaced by the manufacturer, his
customers services or a similarly qualified person.
OVERLOCK SEWING MACHINE
This overlock sewing machine is not intended ...
- to be installed at a permanent location,
– for the processing of other materials (e.g. leather, canvas, sailcloth
and other heavy materials),
- for commercial or industrial use.
Warning about injuries and material damages:
Keep your work space tidy. An untidy workplace can lead to accidents.
Provide adequate lighting when working!
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. You should also wear a hair net if you have long hair.
Avoid adopting an unusual posture. Remain steady and in a well-balanced
position at all times.
If accidents occur as a result of handling the machine with insufficient
care, or failure to follow the safety instructions in this manual, then the
manufacturer cannot accept liability.
Never cover the ventilation slots! Risk of overheating!
Keep the sewing machine oil well away from children.
If swallowed, or should eye contact be made with the sewing machine
oil, consult a doctor immediately.
- 4 -
Items supplied
Overlock Sewing Machine
Oil
Waste container
Accessory box
Operating instructions
The accessories are to be found in the accessory box on the side
of the machine (Fig.1.).
Technical Data
Number of threads 2, 3 or 4
Number of needles 2 or 1
Sewing speed approx. 1200 rpm
Stitch width
right: 3.0 mm - 4.5 mm
left: 5.2 mm - 6.7 mm
Stitch length 1 – 4 mm
Needles HA x 1 Nr. 11-14 or 130/705 Nr. 75-90
Power consumption : Motor: 90 W
Rated voltage: 220 - 240 V
~
, 50Hz
Protection class: II
Replacement blade
(bottom)
2 Needles Nr. 11
4 Needles Nr. 14
(2 in the machine,
pre-installed)
4 Bobbin caps
Upper looper element
Screwdriver small
Screwdriver large
Covering hood
Tweezers
Brush with integrated
unstitcher
The sound intensity level under normal operating conditions amounts to
78dB(A).
Foot pedal
Use only the foot pedal originally supplied with this sewing machine:
- ELECTRONIC FDM Speed Controller
- Type KD - 2902
Fig. 1
- 5 -
Description of the appliance
1 Thread tree
2 Spool support
3 Thread roll centerer
4 Sewing foot lever
5 Adjustment wheel for stitch length
6 Handwheel
7 Connection Footpedal/Power supply
8 Power switch (On/Off switch)
9 Differential transport lever
0 Front flap
q Support plate of the seam width finger
w Free arm
e Stitch plate
r Thread tension selector (left needle)
t Thread tension selector (right needle)
z Thread tension selector (upper looper)
u Thread tension selector (lower looper)
Bringing the upper blade into a rest position
To make certain types of seam, or to more easily operate the adjustment
wheel for cutting width f, you must bring the upper blade i into a
rest position.
For this, press the upper blade i to the right and rotate it a little, so
that it is firmly seated (Fig. 2 and 3).
Needle Information
This machine uses standard commercial flat-shaft needles for sewing machines.
These prevent the incorrect insertion of the needle. You can purchase these
needles in any specialist shop.
You can use needles of the sizes 11 and 14 in this machine.
The adjoining table gives you a brief overview of the differences when using a
needle (for detailed information, see "Setting the seam width).
Upper looper element
For some kinds of stitches you will need to use the upper looper element.
When you need to insert it is described in the individual stitches.
Insert the small wire from behind in the eyelet of the upper looper o and
the plastic bolt, on the other end and from the front, in the hole in the upper
looper o (Fig. 4a).
You can store the upper looper ready for use in the slot behind the front
flap 0 (Fig. 4b).
i movable upper blade (Upper blade)
o Upper looper
p Lower looper
a Sewing foot
s Fixed lower blade
d Seam width switch
f Seam width adjustment knob
Fig. 2
Fig. 3
Fig.4a
Fig.4b
Seam width 3.5 mm 5.7 mm
Employed needle right needle left needle
Thread tension selector green blue
- 6 -
Opening the front flap
Attention!
Always switch the machine off with the power switch 8 when you open
the front flap 0. Risk of Injury!
Slide the front flap 0 to the right (A) and then pull it towards you (B)
(Fig. 5).You will see the upper looper behind the front flap 0.
Note:
While sewing, the front flap 0 must be kept closed!
Preparation
Place the overlock sewing machine on a stable and level surface.
Ensure there is sufficient illumination at your workplace.
Connecting the foot pedal
Insert the plug of the foot pedal into the socket for the foot pedal 7.
Insert the plug into a power socket.
To switch the machine on, press the power switch 8.
Attention!
During absences from the machine or when doing maintenance work,
always remove the plug from the mains power socket. Risk of Injury!
Controlling the sewing speed
The sewing speed is controlled by means of the footpedal. The sewing
speed is changed by applying more or less pressure to the footpedal.
Safety switch
This machine is fitted with a micro safety switch. You cannot start the machine
if the front flap 0 is open. Close the front flap 0 before you start to sew.
Fitting the waste container
The waste container collects remnants during sewing, so that your workplace
stays tidy.
First push the two restraints (A) into the receiving holes (B) (Fig. 6).
Then guide the two restraints (C) into the receiving holes (D) (Fig. 7).
To remove the waste container, pull it forward and then tilt it slightly
(Fig. 8).
Fig. 5
Fig. 8
Fig. 7
Fig. 6
- 7 -
Removing needle(s)
Attention!
Before exchanging the needles, remove the power plug. This prevents an
unintended starting of the machine. If you do not, you run a risk of serious
injury!
Tip!
An exchange of the needles is easier if you first remove the free arm cover
(Fig. 9a)!
1. Turn the handwheel 6 towards yourself until the needles are in the
highest position (Fig. 9b)
2. Loosen the needle retaining screws with the small screwdriver until the
needles are free (Fig. 10).
3. Remove the needles.
Inserting needle(s)
Attention!
Before exchanging the needles, remove the power plug. This prevents an
unintended starting of the machine. If you do not, you run a risk of serious
injury!
1. Hold the needle with the flattened side to the rear.
2. Push the needle as far as it will go into the needle holder.
3. Firmly tighten the needle screws with the small screwdriver (Fig. 10).
Operating the handwheel
Note:
Always turn the handwheel 6 only towards yourself (Fig. 9b).
Adjusting the thread tree
Completely remove the thread tree 1 before threading (Fig. 11).
Turn the thread tree 1 so that the thread guides stand exactly above
the spool supports 2.
In the correct position, the two jointed parts of the thread tree 1 snap
audibly into position.
Place the thread rolls on the thread roll centrings.
If you do not use industrial coils, remove the thread roll centrings. Slide
a spool cap onto each of the thread rolls (Fig. 12). This will hold them in
place when sewing.
Fig.10
Fig. 11
Fig. 12
Fig.9b
Fig.9a
- 8 -
Threading
Note:
On delivery, all 4 threads are already threaded. You can begin sewing im-
mediately. Should you wish to change the thread, and all 4 threads are still
threaded, then proceed as described in the chapter "Changing threads
(binding together)“.
Should you need to rethread all threads from scratch, then proceed as
described in this chapter, "Threading“.
General instructions for threading
Attention!
Before threading, ALWAYS place the power switch 8 at "O" (Off) and
remove the plug from the mains power socket. This prevents an unintended
starting of the machine. If you do not, you run a risk of serious injury!
Correct threading is important, so that the stitches are not irregular and that
the yarn does not break.
Behind the front flap 0 there is a diagram with instructions for threading.
Additionally, the thread guides are marked in various colours.
In the accessory box you will find tweezers, the use of which helps make
threading easier.
Threading is done in this order (Fig. 13/14):
1. First step: Upper looper (red)
2. Second step: Lower looper (yellow)
3. Third step: Thread for the right needle (green)
4. Fourth step: Thread for the left needle (blue)
Note:
When all threads are threaded, and the lower looper thread loosens itself,
proceed as follows:
Unthread the two threads of the needles.
Then thread the lower looper thread.
First then rethread the threads of the two needles again.
The needles must always be the last to be threaded!
For simplification, the individual steps are numbered on the drawings.
Threading the upper looper thread (red)
Attention!
Before threading, ALWAYS place the power switch 8 at "O" (Off) and
remove the plug from the mains power socket. This prevents an unintended
starting of the machine. If you do not, you run a risk of serious injury!
Always use the accompanying drawings for assistance.
Figure 15 shows the thread path of the upper looper thread. The individual
threading positions are numbered and described in detail in the following.
1. Open the front flap 0.
2. Guide the yarn from back to front through the thread tree 1 (1).
143 2
Fig. 13
Fig. 14
Fig. 15
- 9 -
3. Thread the yarn into the thread guide in that you pull the thread down
until it slips under the thread guide (2) (Fig. 16).
4. Firmly hold the yarn with your fingers, guide it between and through
the discs of the thread tension selector z and then pull it down (3)
(Fig. 17).
Note:
The yarn must lie correctly between the two discs of the thread tension
selector z.
5. Thread the yarn in the looper area as per the red markings (Fig. 18).
6. Pull the thread from back to front through the upper looper o.
7. Pull around 10 cm of thread through the looper and place it behind
the stitch plate e.
Fig. 16
Fig. 17
Fig. 18
- 10 -
Threading the lower looper thread (yellow)
Attention!
Before threading, ALWAYS place the power switch 8 at "O" (Off) and
remove the plug from the mains power socket. This prevents an unintended
starting of the machine. If you do not, you run a risk of serious injury!
Figure 19 shows the thread path of the lower looper thread. The individual
threading positions are numbered and described in detail in the following.
1. Guide the yarn from back to front through the thread tree 1 (1).
2. Thread the yarn into the thread guide in that you pull the thread down
until it slips under the thread guide (2) (Fig. 20).
3. Firmly hold the yarn with your fingers, guide it between and through
the discs of the thread tension selector u and then pull it down (3)
(Fig. 21).
Note:
The yarn must lie correctly between the two discs of the thread tension
selector u.
4. Turn the handwheel 6 to yourself until the lower looper p is at the
far right.
Fig. 20
Fig. 21
Fig. 19
- 11 -
5. Thread the yarn in the looper area as per the yellow markings (4 - 8)
(Fig. 22).
6. Firmly hold the yarn with the tweezers about 4 cm from the thread
guide (Fig. 23).
7. Now guide it lightly, from the left and with the tweezers, under the
thread guide.
8. Pull the yarn upwards into the thread guide (9).
9. Lead the yarn to the rear and over the upper end of the lower looper p
(10A) (Fig. 23).
10. Then, carefully pull the yarn down so that it slides into the recess of
the looper (10B) (Fig. 23). For this step also use the drawing which
is attached to the machine!
11. Guide the thread through the looper eyelet (11). The yarn should run
in the groove of the lower looper p (Fig. 23).
12. Draw around 10 cm of yarn through the looper and place it to the
rear
over
the upper looper o and the stitch plate e.
Threading yarn for the right needle (green)
Attention!
Before threading, ALWAYS place the power switch 8 at "O" (Off) and
remove the plug from the mains power socket. This prevents an unintended
starting of the machine. If you do not, you run a risk of serious injury!
Figure 24 shows the thread path of the right needle thread. The individual
threading positions are numbered and described in detail in the following.
1. Guide the yarn from back to front through the thread tree 1 (1).
9
8
10
10
11
Fig. 22
Fig. 23
Fig. 24
- 12 -
2. Thread the yarn into the thread guide in that you pull the thread down
until it slips under the thread guide (2) (Fig. 25).
3. Firmly hold the yarn with your fingers, guide it between and through
the discs of the thread tension selector t and then pull it down (3)
(Fig. 26).
Note:
The yarn must lie correctly between the two discs of the thread tension
selector t.
4. Thread the yarn as per the green markings (4- 7) (Fig. 27/28).
5. Thread the yarn through the right needle (8) (Fig. 28).
6. Lay the yarn to the rear under the sewing foot a.
Fig. 25
Fig. 26
Fig. 27
Fig. 28
5
6
- 13 -
Threading yarn for the left needle (blue)
Attention!
Before threading, ALWAYS place the power switch 8 at "O" (Off) and
remove the plug from the mains power socket. This prevents an unintended
starting of the machine. If you do not, you run a risk of serious injury!
Figure 29 shows the thread path of the left needle thread. The individual
threading positions are numbered and described in detail in the following.
1. Guide the yarn from back to front through the thread tree 1 (1).
2. Thread the yarn into the thread guide in that you pull the thread down
until it slips under the thread guide (2) (Fig. 30).
3. Firmly hold the yarn with your fingers, guide it between and through
the discs of the thread tension selector r and then pull it down (3)
(Fig. 31).
Note:
The yarn must lie correctly between the two discs of the thread tension
selector r.
Fig. 29
Fig. 30
Fig. 31
- 14 -
4. Thread the yarn as per the blue markings (4 - 6) (Fig. 32/33).
5. Thread the yarn through the left needle (7) (Fig. 33).
6. Lay the yarn to the rear under the sewing foot a.
Trial run
When yarn has been threaded for the first time, or after a yarn breakage
it must be rethreaded, proceed as follows:
Lift the sewing foot a.
Hold the ends of the threads between the fingertips of your left hand, slow-
ly turn the handwheel 6 two or three times towards yourself and
then check the threads once again.
Lay the material for a trial run under the sewing foot a and slowly start
to sew.
The material will be automatically fed through.
When the task is complete, continue sewing until an approximately
5cm (2") long length of threads has formed at the end of the material.
Cut through the threads with scissors.
Fig. 32
Fig. 33
4
5
- 15 -
Changing threads (binding together)
Changing threads is quite simple with the following procedure:
1. Cut the yarn above the spool support 2 (Fig. 34) and place the new
roll of thread on the spool support 2.
2. Tie the ends of the new and the old thread together (Fig. 35).
3. Place the thread tension selector r/t/z/u at "0" (Fig. 36) and lift
the sewing foot a.
4. Pull on the other end of the yarn until the knot passes under the sewing
foot a.
5. For threading it in the needle, pull on the other end until the knot is in
the eye of the needle and then cut the yarn to the left and right of the
knot. Then carry out the rethreading.
Set the stitch length
The stitch length can be adjusted from 1.0 to 4.0 mm. Almost all overlock
work is carried out with a stitch length of 2.5 – 3.5 mm.
Turn on the adjustment wheel for stitch length 5 (Fig. 37) to adjust the
stitch length:
A stitch length of 3 mm is recommended for most sewing.
For the working of heavy fabrics, a stitch length of 4 mm is to be re-
commended.
For the working of light fabrics, a stitch length of 2 mm is to be re-
commended..
With these settings you will produce respectable seams and the fabric
will not be crimped.
Setting the seam width
The width of seams can be determined both by changing the needle position
and via the seam width adjustment knob f.
... by using the right or left needle
The width of the seam can be determined by using the left or the right
needle.
Only the left needle is used: 5.7 mm
Only the right needle is used: 3.5 mm
Fig. 34
Fig. 35
Fig. 36
Fig. 37
- 16 -
... by turning the seam width adjustment knob
By using the seam width adjustment knob f, seam width can be adjusted
within the ranges indicated below.
Only the left needle is used: 5.2 - 6.7 mm
Only the right needle is used: 3.0 - 4.5 mm
Setting the seam width adjustment knob
Attention!
Before making adjustments with the seam width adjustment knob f
always place the mains switch 8 at the position "O" (Off). This prevents
an accidental start of the appliance and thus the risk of injury!
Open the front flap 0, this can make the adjustment easier to carry out.
Turn the seam width adjustment knob f to the desired seam width
(Fig. 38). Orientate yourself on the scale on the stitch plate e
(Fig. 39).
Adjust sewing foot pressure
Upon delivery, the sewing foot pressure is set for medium-weight materials.
If you wish to use heavier or lighter materials, adjust the sewing foot pressure
as follows:
For lighter fabrics, you need to reduce the pressure.
For heavier fabrics, you need to increase the pressure.
Insert the small screwdriver into the hole on the upper side of the machine
(Fig. 40). The pressure adjustment screw is located here (A). Ensure that the
screwdriver slips into the slot of the pressure adjustment screw (B) (Fig. 41).
Turn the screwdriver in the direction "+" if you want to increase the pressure.
Turn the screwdriver in the direction "-" if you want to reduce the pressure.
Note:
To return to the factory-set default sewing foot pressure, turn the pressure
adjustment screw as far as it will go anti-clockwise (-). Then turn it 6 rotations in
a clockwise (+) direction.
The standard sewing foot pressure is reset.
Fig. 38
Fig. 39
Fig. 40
Fig. 41
- 17 -
Differential transport
Manner of operation
The machine has two sets of toothed rack feeders, one to the front and one
to the rear. Both sets move independant of each other. Through the differential
feed motion both toothed rack sets can move themselves at various speeds.
With this, the fabric is stretched or gathered, depending on which transport
differential has been set between the front and rear rack feeders.
With the aid of the differential transport, interesting effects can be achie-
ved when sewing overlock seams on stretch materials and diagonally cut
fabrics (Fig. 43).
Note:
When the differential transport lever 9 stands at "1.0", that corresponds
to a differential transport ratio of 1:1. Both toothed feed racks move at the
same rate (Fig. 42).
The differential transport lever 9 can be adjusted in a range from 1:0.7
to 1:2.0.
Gathered overlock seam - Settings
The gathered overlock seam is suitable for the ruffling of sleeves, back
upper parts, skirt seams etc.made of elastic materials such as knitwear
and jersey. The individual parts should be brought together before sewing.
Adjust the differential transport lever 9 to a value higher than 1.0
(Fig. 44). The exact setting depends on the material to be processed
and the desired level of ruffling or gathering.
Therefore always do a sample stitching to test the settings.
Stretched overlock seam - Settings
The stretched overlock seam is suitable for the manufacture of ruffles at the
collar, cuffs and skirt edges etc. in soft, stretchy fabric and knitwear.
Adjust the differential transport lever 9 to a value lower than 1.0 (Fig.
45). The exact setting depends on the material to be processed, and
on the strength of the desired "ruffle effect".
Therefore always do a sample stitching to test the settings.
Hold the seam down with slight firmness before and behind the sewing
foot a so as to keep the textile under tension.
Note:
If you have set a value of "3" or higher on the adjustment wheel for the
stitch length 5, this setting will automatically return to "3" when you set the
differential transport lever 9 to 2.0.
Fig. 42
Fig. 43
Fig. 44
Fig. 45
- 18 -
Free arm sewing
To work tubular-shaped fabrics, such as sleeves or trouser legs, you can
remove the free arm cover.
If appropriate, remove the waste container from the machine.
Slide the free arm cover to the left and pull it off (Fig. 46)..
You can now pull the textiles over the free arm w and work them
(Fig. 47).
To replace the free arm cover, push it onto the free arm w until it clicks
into place and is firmly seated (Fig. 48).
Fig. 46
Fig. 47
Fig. 48
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218

Silvercrest SON 90 A1 Operating Instructions Manual

Tyyppi
Operating Instructions Manual

muilla kielillä