Silvercrest SND 3600 A2 Omistajan opas

NEGATIVE DIGITISER SND 3600 A2

IAN 103081

NEGATIVE DIGITISER

Operating instructions

NEGATIV SCANNER

Betjeningsvejledning

SCANNER FÖR NEGATIV

Bruksanvisning

NEGATIV-DIGITALISIERER

Bedienungsanleitung

NEGATIIVIEN DIGITOINTILAITE

Käyttöohje

DIA SCANNER

Gebruiksaanwijzing

GB / IE Operating instructions Page 1

FI Käyttöohje Sivu 27

SE Bruksanvisning Sidan 53

DK Betjeningsvejledning Side 79

NL / BE Gebruiksaanwijzing Pagina 105

DE / AT / CH Bedienungsanleitung Seite 131

Before reading, unfold both pages containing illustrations and familiarise

yourself with all functions of the device.

Käännä ennen lukemista molemmat kuvalliset sivut esiin ja tutustu seuraavaksi

laitteen kaikkiin toimintoihin.

Vik ut båda bildsidorna och ha den till hands när du läser igenom anvisning-

arna och gör dig bekant med apparatens / maskinens funktioner.

Før du læser, vend begge sidene med billeder frem og bliv bekendt med alle

apparatets funktioner.

Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak

u vertrouwd met alle functies van het apparaat.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und

machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

2 x

1

SND 3600 A2

GB

IE

Index

Introduction . . . . . . . . .2

Information for these

operating instructions . . . . . 2

Copyright . . . . . . . . . . . . . . 2

Limited liability . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . 3

Notes on trademarks . . . . . 3

Proper use . . . . . . . . . . . . . 4

Safety . . . . . . . . . . . . . .4

Basic Safety Instructions . . . 4

Setting up and

connecting . . . . . . . . . .6

Package contents (see

fold-out pages) . . . . . . . . . . 6

Disposal of the packaging . 7

Requirements for the set-up

location . . . . . . . . . . . . . . . . 7

Connecting to a computer . 8

Operating components

(see fold-out pages) . . 14

Handling and operation 14

Insert the negative strip . . . 14

Inserting slides . . . . . . . . . 14

Starting the ArcSoft MediaIm-

pression 2 programme . . . 16

ArcSoft MediaImpression

2 programme . . . . . . . . . . 16

Scanning with the ArcSoft

MediaImpression 2

programme . . . . . . . . . . . . 17

After Use . . . . . . . . . . . . . 20

Cleaning . . . . . . . . . . .21

Troubleshooting . . . .22

Malfunction causes

and remedies . . . . . . . . . . 22

Storage/Disposal . . .23

Storage . . . . . . . . . . . . . . . 23

Disposal of the device . . . 23

Appendix . . . . . . . . . .24

Technical data . . . . . . . . . 24

Note regarding the

conformity declaration . . . 25

Warranty . . . . . . . . . . . . . 25

Service . . . . . . . . . . . . . . . 26

Importer . . . . . . . . . . . . . . 26

GB

IE

2

SND 3600 A2

Introduction

Information for these operating instructions

Congratulations on the purchase of your new appliance.

You have clearly decided in favor of a quality product.

These operating instructions are a component of the Slide & Negative

Scanner SND 3600 A2 (henceforth designated as the device) and

supplies you with important information for intended use, safety and

connection as well as operation of the device. The operating instruc-

tions must be constantly kept available close to the device. They

are to be read and used by anyone assigned to the operation and

repairing of the device. Keep these operating instructions and hand

them over with the device to any future owners.

Copyright

This documentation is copyright protected.

Any copying and/or printing, including partial copying/printing,

as well as reproductions of the diagrams, even in an altered state is

only allowed with written permission from the manufacturer.

Limited liability

All technical information, data and information for connection and

operation, contained in these operating instructions correspond to

the latest at the time of printing and, to the best of our knowledge,

take into account our previous experience and know-how.

No claims can be derived from the details, illustrations and descriptions

in these instructions.

The manufacturer assumes no responsibility for damage caused

by failure to observe the instructions, improper use, inappropriate

repairs, making unauthorized changes or for using unapproved

replacement parts.

3

SND 3600 A2

GB

IE

Warnings

In the current operation instructions the following warnings are used:

WARNING

A warning of this danger level signiﬁ es a possible

dangerous situation.

Failure to avoid this hazardous situation could result in physical

injury or death.

► The directives in this warning are there to avoid personal

injuries.

IMPORTANT

A warning of this danger level signiﬁ es possible

pr

operty damage.

If the situation is not avoided it can lead to property damage.

► The directives in this warning are there to avoid property

damage.

NOTICE

► A notice signiﬁ es additional information that assists in the

handling of the device.

Notes on trademarks

- USB

®

is a registered trademark of USB Implementers Forum, Inc.

All other names and products may be trademarks or registered

trademarks of their respective owners.

GB

IE

4

SND 3600 A2

Proper use

This device is a consumer electronics device intended exclusively for the

non-commercial scanning and digitizing of ﬁ lm negatives and slides.

This device is not intended for any other use or for uses beyond those

mentioned.

WARNING

Danger from unintended use!

Danger can come from the device if used for unintended purposes

and/or other types of use.

► Use the device exclusively for intended purposes.

► Observe the procedures described in these operating instructions.

Claims of any kind for damage resulting from unintended use will not

be excepted.

The operator alone bears liability.

Safety

In this chapter you receive important safety information regarding

handling of the device.

This device complies with the statutory safety regulations. Improper

use can lead to personal injury and property damage.

Basic Safety Instructions

For safe handling of the device observe the following safety information:

■ Before use check the device for visible external damage. Do not

put into operation a de

vice that is damaged or has been dropped.

■ Damaged cables or connections should be replaced by authorized

qualiﬁ

ed persons or by the customer service department.

5

SND 3600 A2

GB

IE

■ This appliance is not intended for use by individuals (including

children) with r

estricted physical, physiological or intellectual abil-

ities or deﬁ ciences in experience and/or knowledge unless they

are supervised by a person responsible for their safety or receive

from this person instruction in how the appliance is to be used.

■ Children should be supervised to ensure that they do not play

with the appliance.

■ Repairs should only be carried out by authorized specialist com-

panies or b

y the customer ser

vice department. Incorrect repairs

can result in signiﬁ cant dangers for the user. In addition warranty

claims become void.

■ A repair to the device during the warranty period may only be

carried out by a customer ser

vice department authorized by the

manufacturer otherwise no additional warranty claims can be

considered for subsequent damages.

■ Defective components may only be replaced with original

replacement par

ts. Only by using original replacement parts can

you guarantee that the safety requirements are complied with.

■ Do not carry out any unauthorised reconstructions or alterations

to the device.

■ Protect the device from moisture and liquid penetration. Do not

place any liquid-ﬁ

lled vessels (such as ﬂ ower vases) next to the

appliance.

■ Keep the device away from naked ﬂ ames, and do not place

candles on or next to the de

vice. This will help to prevent the

spread of ﬁ res.

■ If you move the device quickly from a warm to a cold room or

vice ver

sa, allow the device 30 minutes to acclimatise.

GB

IE

6

SND 3600 A2

Setting up and connecting

WARNING

Personal injury and property damage can occur

during initial operation of the device!

Observe the following safety information to avoid danger:

► Packaging material should not be used as a play thing.

There is a risk of suﬀ

ocation!

Package contents (see fold-out pages)

The following components are included in delivery:

▯ Scanner

▯ 1 x Slide magazine

▯ 2 x Negative holder

▯ Programme CD

▯ Cleaning brush

▯ Operating instructions

NOTICE

► Check the contents to make sure everything is there and for

visible damage.

► If the contents are not complete or are damaged due to

defective pack

aging or through transportation contact the

service hotline (see the section “Service”).

7

SND 3600 A2

GB

IE

Disposal of the packaging

The packaging protects the device from transport damage. The packag-

ing materials are selected from the point of view of their environmental

friendliness and disposal technology and are therefore recyclable.

The recirculation of packaging into the material circuit

saves on raw material and reduces generated waste.

Dispose of packaging material that is no longer needed

according to the regionally established regulations.

NOTICE

► If possible preserve the device's original packaging during

the wa

rranty period so that in the case of a warranty claim

you can package the device properly for return.

Requirements for the set-up location

For safe and faultless operation of the device the set-up location must

fulﬁ ll the following provisions:

■ The device must be placed on a ﬁ rm, ﬂ at and level surface.

■ Do not place the device in a hot, wet or very damp environment

or in the vicinit

y of ﬂ

ammable materials.

■ Place the device so that it is not subjected to direct sunlight.

GB

IE

8

SND 3600 A2

Connecting to a computer

System prerequisites

♦ You will need a computer with a vacant USB port and with the

operating sy

stem Windows

®

XP, Windows

®

Vista, Windows

®

7 or

Windows

®

8 from the Microsoft

®

corporation.

Installation of the ArcSoft MediaImpression 2 programme

NOTICE

► In these operating instructions only the programme sections

are described that y

ou will need for scanning your slides

and/or ﬁ lm negatives. You can ﬁ nd further information in the

programme's on-line help.

► The illustrations and descriptions refer to the operating

system Microsoft

®

Windows

®

7. The illustration depictions

can diﬀ er, depending on the display settings, with other

operating systems.

♦ Insert the supplied programme CD into your computer’s CD drive.

The window “

Automatic playback” will be displayed.

♦ Click on the button “run autorun.exe”.

The installation begins and the start window is displayed.

9

SND 3600 A2

GB

IE

NOTICE

► If you have switched oﬀ the autostart function and the installa-

tion process does not begin automatically you can star

t the

installation process by double clicking on the ﬁ le "autorun.exe"

in the CD's main directory.

♦ Click on the button “Arcsoft Software” to install the “ArcSoft

MediaImpression 2“ programme.

The window for selecting the installation language is shown.

♦ Select the desired installation language and click the “OK” button.

The installation wizard will be conﬁ gured.

GB

IE

10

SND 3600 A2

The start window of the installation wizard will be displayed.

♦ Click on the button “Continue



>”.

The window “License agreement” will be displayed.

♦ Click on the button “Yes”.

The window for entering the user information and the license

key is shown.

11

SND 3600 A2

GB

IE

♦ Enter your choice of username and the 24-digit license key (see

CD case).

♦ Conﬁ rm your entry by clicking the “Continue



>” button.

The window for the selection of the installation directory will be

displayed.

♦ Select the desired installation directory and click on the button

“Continue



>”.

The window for the selection of the programme folders (Entry in

the Windows start menu) will be displayed.

♦ Select the desired programme folder and click on the button

“Continue



>”.

GB

IE

12

SND 3600 A2

The programme will be installed and the installation progress

will be displayed.

The window “Associated ﬁ le formats” will be displayed.

♦ Select the ﬁ le format that is to be associated with the programme

and click on the button “Continue >”.

13

SND 3600 A2

GB

IE

The display will show that the installation has been completed.

♦ Click on the button “Finish”.

The start window will be displayed again.

♦ Click on the button “Exit Installation” to exit the installation

programme.

Connection

♦ Connect the USB cable

4

to a USB port on your computer.

The computer recognizes the new hardware and starts the

automatic driver installation.

GB

IE

14

SND 3600 A2

Operating components (see fold-out pages)

LED PWR

2

SCAN button

3

Insert slot for the negative or slide magazine

4

USB connection cable

5

Film holder

6

Slide magazine

7

Cleaning brush

Handling and operation

In this chapter you receive important information for the handling

and operation of the device.

Insert the negative strip

♦ Release the fastener on the front of the ﬁ lm holder

5

and open

the holder.

♦ Insert the ﬁ lm strip, correctly orientated, into the holder. Ensure

that holes of the negative strip ar

e placed on the corresponding

retaining tabs on the holder, so that the negative strip can not

move.

♦ Close the holder making sure that the cover locks into place.

Inserting slides

♦ Place the slides, with the sides the right way round, into the

intended slot of the slide magazine

6

.

♦ First guide the slide magazine

6

, with the viewing window

leading, into the insert slot

3

.

By means of the slider, located laterally on the slide magazine

6

, the

slides contained in the slots are pushed individually into the scanner.

15

SND 3600 A2

GB

IE

♦ For this, ﬁ rst slide the slider away from the scanner to the dead

stop. Then carefully mo

ve the slider back towards the scanner.

NOTICE

► A slide located in the scanner is thereby removed from the

appliance and a new slide is pushed into the visual r

ange of

the scanner.

► Be sure to insert a new slide into the scanner slowly. If this

happens too quickly, then the slide could glide outside the

visual range of the scanner.

♦ When you have decided to ﬁ nish scanning the slides, remove

the slide magazine

6

from the insert slot

3

. Remove the

last slide from the bottom of the viewing window of the slide

magazine

6

.

GB

IE

16

SND 3600 A2

Starting the ArcSoft MediaImpression 2 programme

♦ Start the ArcSoft MediaImpression 2 programme by double

clicking on the programme icon on the desktop or select the

corresponding input from the start menu.

ArcSoft MediaImpression 2 programme

There are four options available:

1. Image: Open an available image on the computer or memory

medium.

2. Capture: For the scanning of new images

3. Simple reproduction: Fast image editing

4. Image editing tools: Detailed image editing

NOTICE

► In these operating instructions only the programme sections

are described that y

ou will need for scanning your slides

and/or ﬁ lm negatives. You can ﬁ nd further information, e.g.

on picture editing and correction, in the programme’s on-line

help.

1

2

3

4

Sivu latautuu ...

Silvercrest SND 3600 A2 Omistajan opas

Tämä käsikirja sopii myös

Silvercrest SND 3600 A2 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat