Avery Dennison 9906 Quick Reference Manual

Monarch is a trademark of Avery Dennison

Retail Information Services LLC.

Avery Dennison is a trademark of Avery Dennison Corp.

Serial Port

Host USB

Device USB

Power Cable

Connection

Parallel Port

(optional)

QUICK REFERENCE

This Quick Reference contains supply loading and general care

and maintenance procedures for the Monarch® 9906 printer. For

more detailed information, refer to the Operator’s Handbook

available on our Web site (www.monarch.com

). For information

about creating formats, configuring the printer, or programming

the printer, refer to the Packet Reference Manual on our Web

site.

Review the safety information in the Regulatory Compliance

document included with your printer. Information in this

document supercedes information in previous versions. Check

our Web site for the latest documentation and

release information.

Connecting the Cables

The power supply automatically

switches between 115V and 230V.

1. Plug the power cable into the

socket and the other end into

a grounded electrical outlet.

2. Connect the communications

cable into the appropriate port.

3. Turn on the printer. Press ( I )

to turn on and ( O ) to turn off

the printer.

Using the Control Panel

The control panel consists of a four-

line LCD display, three function

buttons, and two navigation buttons.

The function of each button varies

depending on the task.

The LCD display:

 Indicates power when text or

other information is shown

 Indicates conditions requiring

immediate attention (low battery,faults, errors) using a red

background

 Shows menu prompts, printer settings, function button

assignments, values, etc.

Function

Buttons

Navigation

Buttons

MPCL

Online

FEED

TLabel MENU

2-EN

Printhead Tab

Retaining Latch

Loading Labels or Tags

1. Open the cover.

2. Unlock the printhead by turning the retaining latch.

3. Lift the printhead assembly using the printhead tab until the

assembly locks into place.

4. Place the roll of supply on the supply holder, located against

the inside of the printer.

5. Adjust the supply holder guide so that it barely touches the

roll, making sure the supply roll turns freely.

Supply Holder Guide

Supply Holder

EN-3

6. Push down on the supply lever to unlock the supply guide.

7. Lay the label strip across the supply guide so that a few

inches extend past the front of the printer.

8. Tuck the supply under the nibs and in between the die cut

sensor.

9. Adjust the supply guide so that it barely touches the supply.

Push up on the supply lever to lock the supply guides into

place.

10. Hold the printhead assembly by the printhead tab while

pushing the printhead release.

Printhead Release

Printhead Tab

Supply Lever

Nibs

Die Cut

Sensor

4-EN

11. Close the printhead by pressing down on the thumb well until

you hear it click into place.

12. Close the printer’s cover.

13. Press FEED.

Loading Labels for the Optional Peel Mode

1. Remove the labels from the first 10 inches of the liner.

2. Press down on the exit cover tabs to open the exit cover.

3. Feed the liner over the peel bar, along the chute, and out

through the lower opening in the exit cover.

4. Close the exit cover.

5. Close the printer’s cover.

6. Press FEED.

For additional supply loading options, refer to the Operator’s

Handbook.

Peel Roller

Lower Opening

Platen Roller

Peel Bar

EN-5

Adjusting the Printhead Pressure Dials

The default setting is least pressure, which provides optimal

printing in most cases. If you see smudging, ribbon wrinkling, or

poor print quality, you may need to adjust the printhead pressure

dials.

The two dials are located on either edge of the printhead

assembly (inside and outside). The dials may be set to different

positions; however, the inside dial should be equal to or more

pressure than the outside dial. When using 4” wide supply both

knobs should be set at equal pressure. Use a coin or flathead

screwdriver to adjust the dials.

Each dial has four settings:

 Least pressure

 Light pressure

 Medium pressure

 Most pressure

Print a test label to check the printhead pressure; make

adjustments as necessary. Refer to the Operator’s Handbook for

additional information.

Loading Ribbon

1. Open the cover.

2. Unlock the printhead by turning the printhead retaining latch.

3. Lift the printhead assembly using the printhead tab until the

assembly locks into place.

Printhead

Pressure Dials

Least

Pressure

Most Pressure

6-EN

4.

Push the deflector tab down.

5. Slide the extra ribbon core onto the take-up reel as far as it

will go.

6. Remove the new ribbon from the package.

7. Slide the ribbon all the way onto the back reel. Carefully

unwind a few inches from the bottom of the ribbon roll.

8. Feed the ribbon under both ribbon rollers and printhead.

9. Make sure the ribbon is straight and centered throughout the

path.

10. Tape the ribbon to the take-up core.

11. Rotate the take-up core until the leader is past the printhead.

Take-u

p

Reel

Printhead

Assembly

Deflector Tab

Thumb

well

Ribbon

Rollers

EN-7

12.

Remove any slack in the ribbon by turning the take-up reel

clockwise.

13. Hold the printhead assembly by the printhead tab while

pressing down on the printhead release.

14. Close the printhead by pressing down on the thumb well until

you hear it click into place.

15. Close the printhead. Close the printer’s cover.

16. Press FEED.

Cleaning

Clean the printhead as described to maintain printhead life.

Caution: Do not use sharp objects to clean the printhead or

touch the printhead; this may damage the printhead

and require a service charge.

1. Turn off the printer, open the cover and the printhead

assembly.

2. Remove the label roll and ribbon (when cleaning the

printhead).

3. Press down on the exit cover tabs to open the exit cover.

4. Spray the supply path, including supply sensor, with

compressed air to remove dust.

5. Use a CLEAN-STRIP (part number 120350) to clean and

remove adhesive build-up from the platen roller, peel bar,

sensor, and printhead.

6. Let the printer dry, then reload supplies.

7. Close the exit cover.

8. Close the printhead assembly and the printer’s cover.

9. Turn on the printer. Press FEED.

Platen Roller

Printhead

Sensor

Peel Bar

8-EN

Selecting the Interpreter

The 9906 printer includes four Interpreter options; MPCL, MLI,

WMS XML, and Easy-Plug. For more information about MLI refer

to the MLI Quick Reference, for more information about WMS

XML refer to the XML Quick Reference, for more information

about Easy-Plug refer to the Easy-Plug Manual included on the

CD-ROM.

From the Main Menu, select Setup, then:

1. Press  or  until Interpreter is on the display.

SETUP

 Interpreter 

MPCL

CHANGE BACK

2. Press CHANGE then press  until Easy-Plug is on the display.

MAIN MENU

Interpreter

 Easy-Plug 

SET CANCEL

3. Press SET to save the change.

 The printer reboots automatically after selecting an

interpreter. This process may take several seconds.

 When you print test labels with MLI set as the interpreter,

the model number appears as M9906MLI.

 When you print test labels with Easy-Plug set as the

interpreter, the model number appears as M9906EP.

EN-9

RFID (if installed)

The 9906 printer with RFID has been engineered to program

(encode) an RFID (Radio Frequency Identification) label

(commonly called “RFID tags”) before the label’s format is

printed. RFID tags contain an embedded RFID inlay (chip and

antenna).

RFID is only available using die cut or black mark supplies.

The printer supports Class 1 Generation 2 (C1Gen2) protocol

encoding.

RFID supplies can be damaged by static electricity.

Ground yourself by touching metal, such as the

printer’s metal base, before handling the supplies.

The UHF radio operates in the 902 – 928 MHz frequency range

in accordance with FCC Rules and Regulations.

RFID Setup Menu

Use the RFID Setup Menu to Read a tag, set the RF Power, and

Clear Data.

The Read Tag menu item lets you read the EPC data

programmed into an RFID tag.

Refer to the RFID Web Setup Utility at

http://www.servisource1.com/prnutil/rfidsetup

to set the RF

Power setting.

The printer stores the number of successful and failed

programmed tags. Clear this record using the Clear Data menu

item. Depending on your application and volume of labels

printed, you may want to clear this data daily or after each batch.

To access the RFID settings, from the Main Menu select Setup,

then RFID.

If the RFID tag is not programmable for any reason, the label

may print with an overstrike pattern, indicating that it should not

be used. Your System Administrator should set the desired Error

Action accordingly.

If you see RFID errors 740 – 749, see your System

Administrator.

Refer to the Operator’s Handbook and Application Notes for more

information.

SETUP

← RFID →

SELECT BACK

10-EN

Troubleshooting

This section lists common problems and their solutions.

Problem Action

Error message

appears during

startup

Turn off the printer, wait fifteen seconds

and then turn on the printer. Call

Customer Service if the error message

reappears.

Does not print.

Check supply and ribbon, send a

corrected format and batch packet.

Does not feed. Adjust the printhead pressure dials.

Partially printed data.

Clean the printhead, send a corrected

format packet.

Light/Heavy printing,

printing shadows or

voids.

Clean the printhead, change supply,

adjust the print contrast, check the

printhead pressure dials, check the

ribbon.

Serial bar codes do

not scan.

Leave printhead unlatched when not in

use, use a print speed of 2.5 ips, adjust

the print contrast.

Liner is wrapped

around platen or peel

roller.

Carefully remove the liner. Make sure

the liner tears at the saw-toothed tear

edge when using backfeed and peel

mode.

Printer does not read

or program the RFID

tag.

See your System Administrator

EN-11

Common Errors

Error Description/Action

002 Name must be 1 to 8 characters inside quotes.

005 Invalid supply width.

018 Invalid code page selection.

025 Data length is too long.

101 Format referenced by batch not in memory.

400 Invalid character following {.

403 Field separator was not found.

409 Printer memory is full. Delete unused items.

410 Parity mismatch.

411 Framing error (baud rate mismatch).

412 Flow control mismatch.

413 Online receive buffer is full. Check flow control.

611 Font, bar code, or density in the batch does not fit the format.

612 Data in this line of the batch is missing or doesn’t match format.

613 Reference point off supply.

614 Portion of field off supply or invalid character in the packet.

703

Printer sensed a calibration of different-sized black marks.

Make sure the correct supply type is loaded.

704

Printer has not sensed a supply mark when expected or is out

of supplies. Make sure your printer is set to the appropriate

supply type. Reload supply. Clean the sensor.

751

Printer did not sense a black mark when expected. Press

ESCAPE to continue printing. Change supply.

752 Printer sensed a mark in the wrong place.

753 Printer sensed a mark that is too long.

754

Check for a ribbon jam or remove any slack in the ribbon. Load

a new ribbon.

755 Printhead is open. Close the printhead.

756 Load supply and/or clean the sensor.

757

Load supply (supply length mismatch). Press FEED.

758

Supply is not seen, on-demand sensor is broken, or a label was

removed too quickly. Check for a label jam or reload supplies.

763

Waiting to dispense label. Press FEED.

765

Printhead has less than 8 bad dots and can shift bar code fields

to avoid bad dots. Press ESCAPE to continue printing.

768

Printhead has more than 8 bad dots or is not connected.

Connect or replace the printhead.

12-EN

RFID Errors

See the RFID Application Notes for more information. Check with your System

Administrator about the format. The printer does not recalibrate (feed a blank

label) after an RFID error.

Error Description/Action

052

Data type in the RFID Data Field is invalid.

053

The starting block in the RFID Data Field is invalid.

226

Rule Record Line xx. Upload device is invalid.

228

Memory class identifier is invalid.

229

Byte code is invalid.

230

Lock code is invalid.

715 Invalid data length/data mismatch in the RFID Data Field. This

error also occurs when there is an error in the Expanded

C1Gen2 fields.

732 RFID Hardware Error. A non-RFID printer received a format

containing an RFID Data Field.

740

Command, hardware, or memory allocation error.

741 RFID tag missing - not found in the area inside the printer where

the RFID tag is programmed. Check supply loading. Make sure

the RFID tag was not moved out of the programmable range.

742 Tag erase failed. The RFID tag was found in the RF Field, but

could not be erased.

743 Program tag failed. The RFID tag was found in the RF Field, but

could not be programmed.

744 Tag locked fail. The RFID tag is unable to be programmed

because it is already locked.

746 Lock tag fail. The RFID tag has not been locked to prevent

reprogramming.

747 Time out failure. An RFID command (read, program, etc.) has

failed to complete in the maximum amount of allowed time.

748 Invalid data length/data mismatch from RFID interrogator

module.

749 RFID Verify Fail. The RFID verification process failed after

writing (programming) tag.

DA-1

Seriel port

Værts-USB

Enhedens

US

B

Tilslutning af

netledning

Parallel port

(valgfri)

KORT OVERSIGT

Denne korte oversigt beskriver, hvordan der fyldes medie på Monarch®

9906-printeren, og hvordan den vedligeholdes. Der er mere detaljerede

oplysninger i Operator’s Handbook, som du finder på vores websted

(www.monarch.com

). Oplysninger om at oprette formater og konfigurere

eller programmere printeren finder du i Packet Reference Manual på

vores websted.

Gennemgå sikkerhedsoplysningerne i dokumentet Regulatory

Compliance, som følger med printeren. Oplysningerne i dette dokument

erstatter oplysningerne i tidligere versioner. Tjek vores websted for ny

dokumentation og oplysninger om nye versioner.

Tilslutning af kablerne

Strømforsyningen skifter automatisk mellem

115V og 230V.

1. Sæt netledningen i stikket

og i en jordforbundet

stikkontakt.

2. Sæt kommunikationskablet

i den tilhørende port.

3. Tænd printeren. Tryk på ( I )

for at tænde og på ( O ) for at

slukke printeren.

Brug af betjeningspanelet

Betjeningspanelet består af et

LCD-display med fire linjer, tre funktions-

knapper og to navigationsknapper.

De enkelte knappers funktion varierer

afhængigt af opgaven. Displayet:

 Tænder, når der er tekst eller andre

oplysninger, der skal vises

 Viser tilstande, der kræver umiddelbar

indgriben (opbrugt batteri, fejl),

på rød baggrund

 Viser menuprompter,

printerindstillinger, tildeling af

funktionsknapper, værdier m.m.

MPCL

Online

FEED

TLabel

MENU

Funktions

-kna

pp

er

Navigations

-knapper

2-DA

Printhovedtap

Udløsergreb

Isætning af etiketter eller tags

1. Åbn dækslet.

2. Frigør printhovedet ved at dreje på udløsergrebet.

3. Løft printhovedanordningen vha. printhovedtappen, indtil hele

anordningen låses på plads.

4. Anbring medierullen i medieholderen, som er placeret langs

indersiden af printeren.

5. Juster medieholderens styr, så det lige akkurat berører rullen, men

vær opmærksom på, at rullen skal kunne dreje ubesværet.

Medieholderens styr

Medieholder

DA-3

6.

Tryk mediehåndtaget ned for at frigøre mediestyret.

7. Anbring etiketstrimlen over mediestyret, så ca. 5 cm er synlig på

printerens forside.

8. Anbring mediet under udspringene og mellem

udstansningssensoren.

9. Juster mediestyret, så det kun lige akkurat berører mediet. Skub

mediehåndtaget op for at låse mediestyrene på plads.

10. Hold i printhovedtappen på printhovedanordningen, mens du trykker

på printhovedudløseren.

Printhovedudløser

Printhovedtap

Udspring

Mediehåndtag

Udstansnings-

sensor

4-DA

11.

Luk printhovedet ved at trykke på fordybningen til tommelfingeren,

indtil du kan høre, at det klikker på plads.

12. Luk printerens dæksel.

13. Tryk på FEED (Fremfør).

Isætning af etiketter til den valgfri peel-tilstand

1. Fjern etiketterne på de første 25 cm af bærebanen.

2. Tryk på udføringsdækslets tapper for at åbne udføringsdækslet.

3. Før bærebanen over peel-listen langs slisken og ud gennem den

udføringsdækslets nederste åbning.

4. Luk udføringsdækslet.

5. Luk printerens dæksel.

6. Tryk på FEED (Fremfør).

Der er flere oplysninger om isætning af medie i Operator’s Handbook.

Peel-valse

Nederste åbning

Fremføringsvalse

Peel-liste

DA-5

Mindst

tr

y

k

Størst tr

y

k

Justering af printhovedets tryk

Standardindstillingen er så lille et tryk som muligt, hvilket i de fleste

tilfælde giver optimal udskrivning. Det kan være nødvendigt at justere

printhovedets tryk i tilfælde af udtværing, rynket farvebånd eller dårlig

udskriftskvalitet.

De to knapper er placeret på printhovedets kant (ind- og udvendigt).

Knapperne kan have forskellige positioner; men trykket skal på

indersiden være lig med eller større end på ydersiden. Hvis der

anvendes et medie, der er 4” bredt, skal begge knapper indstilles til

samme tryk. Brug en mønt eller en fladbladet skruetrækker til justering

af trykket.

Hver knap har fire

indstillinger.

 Mindst tryk

 Let tryk

 Medium tryk

 Størst tryk

Udskriv en testetiket for at kontrollere printhovedets tryk. Foretag

justeringer, hvis det er nødvendigt. Du finder yderligere oplysninger i

Operator’s Handbook.

Isætning af bånd

1. Åbn dækslet.

2. Frigør printhovedet ved at dreje printhovedets udløsergreb.

3. Løft printhovedanordningen vha. printhovedtappen, indtil hele

anordningen låses på plads.

Knapper til justering

af printhovedets tryk

6-DA

4.

Tryk deflektortappen ned.

5. Skub den ekstra båndkerne så langt som muligt over på

optagningsrullen.

6. Tag det nye bånd ud af emballagen.

7. Skub båndet helt over på den bageste rulle. Rul forsigtigt ca. 5 cm af

i bunden af båndrullen.

8. Før forsigtigt båndet under de to båndvalser og printhovedet.

9. Sørg for, at båndet er lige og centreret langs hele banen.

10. Sæt båndet fast på optagningskernen med tape.

11. Drej optagningskernen, indtil indløbsstrimlen har passeret

printhovedet.

12. Fjern eventuelt slæk på båndet ved at dreje optagningsrullen med

uret.

Løft rullen op

Printhovedanordning

Deflektortap

Fordybning til

tommelfingeren

Bǻndvalser

DA-7

13.

Hold i printhovedtappen på printhovedanordningen, mens du trykker

på printhovedudløseren.

14. Tryk på fordybningen til tommelfingeren, indtil du hører, at det

klikker på plads, for at lukke printhovedet.

15. Luk printhovedet. Luk printerens dæksel.

16. Tryk på FEED (Fremfør).

Rengøring

Du skal rengøre printhovedet som beskrevet, for at det kan holde

længe.

Forsigtig: brug ikke skarpe genstande til rengøring af printhovedet,

og rør ikke ved printhovedet. Det kan beskadige

printhovedet, så en servicetekniker skal udskifte det.

1. Sluk printeren, og åbn dækslet og printhovedanordningen.

2. Fjern etiketrullen og båndet (mens printhovedet rengøres).

3. Tryk på udføringsdækslets tapper for at åbne udføringsdækslet.

4. Brug trykluft til at fjerne støv og smuds fra sensoren.

5. Brug en CLEAN-STRIP (varenummer 120350) til rengøring og til at

fjerne klæbestof, som har sat sig fast på fremføringsvalsen, peel-

listen og printhovedet.

6. Lad printeren tørre, før du sætter bånd og medie i igen.

7. Luk udføringsdækslet.

8. Luk printhovedanordningen og printerens dæksel.

9. Tænd printeren. Tryk på FEED (Fremfør).

Valg af fortolker

9906-printeren har fire fortolkere: MPCL, MLI, WMS XML og Easy-Plug. Der er

flere oplysninger om MLI i MLI Quick Reference, om WMS XML i XML Quick

Reference og om Easy-Plug i Easy-Plug Manual, som medfølger på cd-rom.

Vælg Setup i hovedmenuen, og:

1. Tryk på  eller , indtil Interpreter vises på displayet.

SETUP

 Interpreter 

MPCL

CHANGE BACK

Fremførings

Printhoved

Sensor

Peel-liste

8-DA

2. Tryk på CHANGE og derefter på , indtil Easy-Plug vises på displayet.

MAIN MENU

Interpreter

 Easy-Plug 

SET CANCEL

3. Tryk på SET for at gemme ændringen.

 Printeren genstarter automatisk, når der er valgt fortolker. Det kan

tage flere sekunder.

 Modelnummeret vises som M9906MLI, når der udskrives testetiketter

med MLI valgt som fortolker.

 Modelnummeret vises som M9906EP, når der udskrives testetiketter

med Easy-Plug valgt som fortolker.

RFID (hvis installeret)

9906-printeren med RFID er udviklet til at kode en RFID-etiket (Radio Frequency

Identification) (i daglig tale kaldet en "RFID-tag") inden udskrivning af etikettens

format. RFID-tags indeholder et integreret RFID-mønster (chip og antenne).

RFID er kun tilgængelig, når der anvendes udstandsede forbrugsstoffer eller

forbrugsstoffer med sort mærke.

Printeren understøtter 2. generation klasse 1-protokolkodning (C1Gen2).

RFID-forbrugsstoffer kan beskadiges af statisk elektricitet. Sørg for

jordforbindelse, f.eks. ved at berøre metal (printerens metalbund),

inden håndtering af forbrugsstofferne.

UHF-radioen fungerer på frekvensområdet 902 – 928 MHz i

overensstemmelse med FCC-reglerne og -bestemmelserne.

Menu til opsætning af RFID

Brug menuen RFID Setup (Opsætning af RFID) til at læse en tag, indstille HF-

effekten og slette data.

Via menupunktet Read Tag (Læs tag) kan du læse EPC-data programmeret på

en RFID-tag.

Se RFID Web Setup Utility på http://www.servisource1.com/prnutil/rfidsetup

for

at få HF-effekten vist.

Printeren indeholder et antal fungerende og ikke-fungerende programmerede

tags. Slet dem vha. menupunktet Clear Data (Slet data). Det kan være

nødvendigt at slette disse dagligt eller efter hvert parti afhængigt af formålet

med og mængden af etiketter, der udskrives.

Vælg Setup (Opsætning) i hovedmenuen og derefter RFID for at få adgang til

RFID-indstillingerne.

Hvis RFID-taggen af en eller anden årsag ikke kan programmeres, overskrives

etiketten muligvis med et stregmønster for at vise, at den ikke skal anvendes.

Systemadministratoren kan angive, hvad der skal ske i tilfælde af fejl.

Kontakt systemadministratoren, hvis RFID-fejl 740 – 749 vises.

Se Operator’s Handbook og Application Notes for at få flere oplysninger.

SETUP

← RFID →

SELECT BACK

Sivu latautuu...

Avery Dennison 9906 Quick Reference Manual

Tämä ohje sopii myös

Avery Dennison 9906 Quick Reference Manual

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat