Dremel 3D20 Idea Builder Original Instructions Manual

Original instructions 2

Übersetzung der Originalbedienungsanleitung 27

Traduction de la notice originale 54

Traducción de las instrucciones originales 81

Traduzione delle istruzioni originali 108

Vertaling van de originele gebruiksaanwijzing 134

Oversættelse af betjeningsvejledning 161

Översättning av originalinstruktioner 186

Oversettelse av originalinstruksjonene 211

käännös alkuperäisistä ohjeista 236

Tradução das instruções originais 261

EN

FR

IT

NL

SV

FI

PT

DE

ES

DA

NO

ORIGINAL INSTRUCTIONS

GENERAL SAFETY WARNINGS

!

WARNING

READ ALL

INSTRUCTIONS IN THIS

MANUAL AND FAMILIARIZE YOURSELF

WITH THE DREMEL 3D20 BEFORE SETUP

AND USE. FAILURE TO COMPLY WITH THE

WARNINGS AND INSTRUCTIONS MAY RESULT IN

FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE,

OR PERSONAL INJURY. SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE REFERENCE

WORK AREA SAFETY

a. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b. Do not operate Dremel 3D20 in the presence of

ammable liquids, gases or dust. Dremel 3D20

creates high temperatures which may ignite the

dust or fumes.

c. Store idle 3D20s out of reach of children and

other untrained persons. Injury can occur in

hands of untrained users.

ELECTRICAL SAFETY

a. Always use the Dremel 3D20 with a properly

grounded outlet. Do not modify Dremel 3D20

plug. Improper grounding and modied plugs

increase risk of electric shock.

b. Do not use Dremel 3D20 in damp or wet

locations. Do not expose Dremel 3D20 to rain.

Presence of moisture increases risk of electric

shock.

c. Do not abuse the cord. Never use the cord for

pulling or unplugging the Dremel 3D20.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

d. Avoid using this product during an electric

storm. There may be a remote risk of a power

surge from lightning that may result in an electric

shock.

e. In case of emergency unplug Dremel 3D20 from

outlet.

PERSONAL SAFETY

a. Stay alert, watch what you are doing and

use common sense when operating a Dremel

3D20. Do not use Dremel 3D20 while you are

tired or under the inuence of drugs, alcohol

or medication. A moment of inattention while

operating Dremel 3D20 may result in personal

injury.

b. Use personal protective equipment. The use of

protective equipment such as heat resistant gloves

and safety glasses will reduce the risk of personal

injuries.

c. Dress properly. Do not wear loose clothing or

Jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, Jewellery

or long hair can be caught in moving parts.

DREMEL 3D20 USE AND CARE

a. Before every use check Dremel 3D20 for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the Dremel 3D20’s operation.

If damage is suspected then have the Dremel

3D20 repaired by an authorised Dremel service

centre before use. Use of Dremel 3D20 when

damaged may result in poor quality of object

creation, further equipment damage, property

damage or personal injury.

b. Do not touch the extruder tip during Dremel

3D20 operation or until it has cooled down to

at least 60°C (140°F). Contact with the extruder tip

during or after operation before tip has cooled may

result in personal injury.

c. Set up the Dremel 3D20 in a well-ventilated

area. Provide at least 8 inches of unobstructed

spacing around Dremel 3D20. Dremel 3D20

melts plastic during building. Plastic odours emitted

during Dremel 3D20 operation may irritate eyes

and airways. Locating Dremel 3D20 close to

surrounding objects prevents proper ventilation.

d. Do not reach inside the Dremel 3D20 while it is

in operation. Contact with Dremel 3D20 moving

parts during operation may result in poor build

quality, equipment damage or personal injury.

e. Do not leave the Dremel 3D20 unattended

during operation. Use of Dremel 3D20 by persons

unfamiliar with these warnings and instructions may

result equipment or property damage and personal

injury.

f. Use only DREMEL PLA lament. Use of lament

not authorized by Dremel may result in equipment

and property damage.

g. Ensure small objects created by Dremel 3D20

are not accessible to young children. Small

objects are potential choking hazards for young

children.

h. Do not create illegal or inappropriate objects

using Dremel 3D20.

i. Do not use Dremel 3D20 to create objects

intended for use with candles, liquid fuels,

and other heat sources. Plastic may melt when

exposed to re or other heat sources. Such use of

objects created by Dremel 3D20 may result in re,

property damage and personal injury.

j. Do not use Dremel 3D20 to create objects

intended for food or drink applications

such as preparation, decoration, storage, or

consumption. Such use of objects created by

Dremel 3D20 may result in illness or personal

injury.

k. Do not use Dremel 3D20 to create objects

intended with use with electrical components or

housings of electrical components. PLA plastic

is not suitable for electrical applications. Such use

of objects created by Dremel 3D20 may result in

property damage and personal injury.

l. Do not put plastic objects in or around your

mouth. PLA plastic is not suitable for food or drink

preparation and food utensils. Such use of objects

created by Dremel 3D20 may result in illness or

personal injury.

m. Do not use Dremel 3D20 to create objects

intended for chemical storage. PLA plastic is not

suitable for chemical storage. Such use of objects

created by Dremel 3D20 may result in property

damage and personal injury.

n. Do not modify Dremel 3D20 or alter factory

settings. Modications may result in equipment

and property damage, and personal injury.

o. Do not expose Dremel 3D20 to temperatures

exceeding 70°C (158°F). Dremel 3D20 may

become damaged. Dremel 3D20 is intended to

operate in temperature between 16-29° C (60 - 85°

F).

GB

2

p. Do not move or bump Dremel 3D20 or the

extruder during operation. The object may build

incorrectly.

q. Do not change colour of lament or spool

during building. Doing so will cancel the object

and may damage the extruder.

r. Do not pull the lament out until instructed

by the touch screen. Doing so may damage the

extruder.

s. Use extra care not to damage the extruder tip

when clearing debris. Dremel 3D20 will not work

properly with damaged extruder tip and will require

replacement.

t. Before every build make sure that the build

platform is covered with Dremel specied build

tape. Use of improper build tape may result in

equipment damage and poor object build quality.

u. Be aware of your body position when using

hand tools to remove objects from the build

platform. Sudden tool slip and improper body

position during object removal from the build

platform may result in personal injury.

v. Avoid scratching the build platform when

removing objects. Scratches in the build platform

will result in improper object creation.

w. Dremel is not responsible for structural integrity

or utility of objects created using Dremel

3D20. Structural models created by inexperienced

designers may result in property damage and

personal injury.

SERVICE

a. Always unplug Dremel 3D20 from its power

before performing any service procedures.

Failure to do so may result in personal injury and

equipment damage.

b. Have your Dremel 3D20 serviced only by an

authorized Dremel service centre using only

Dremel replacement parts. This will ensure that

proper operation and safety of Dremel 3D20 is

maintained.

c. Use only Dremel approved materials and

components. Use of object materials, or 3D

objects other than Dremel

®

approved object

materials and genuine Dremel

®

components may

void warranty.

TABLE OF CONTENTS

General safety warnings ......................................2

Table of contents...................................................3

Used symbols ........................................................ 3

Information on Intellectual Property ...................3

Functional Description and Specications ........4

3D20 Resources ....................................................5

Glossary of Terms .................................................5

Getting to know your 3D20 .................................. 7

Introduction ............................................................9

Kit Contents and Unpacking ................................9

Touch Screen .......................................................11

Software Install and Registration ...................... 16

Dremel Software Overview .................................17

Getting Ready to Build .......................................19

Building ................................................................21

Building from the SD Card .................................21

Building From Your Computer...........................22

Removing Your Object ........................................22

Unloading and Replacing Filament Spool ........23

Maintenance and Service ...................................24

Unclogging the extruder ....................................25

Cleaning the exterior ..........................................25

Cleaning the extruder tip ...................................25

Cleaning the touch screen ................................. 25

Best practices ......................................................25

Dremel

®

Consumer Limited Warranty................26

USED SYMBOLS

Symbol Name Designation/

Explanation

!

WARNING

Warning symbol

Alerts user to warning

messages

Read manual

symbol

Alerts user to read

manual

!

WARNING

THIS IS A CLASS A PRODUCT. IN

A DOMESTIC ENVIRONMENT THIS

PRODUCT MAY CAUSE RADIO INTERFERENCE IN

WHICH CASE THE USER MAY BE REQUIRED TO

TAKE ADEQUATE MEASURES.

INFORMATION ON INTELLECTUAL

PROPERTY

The Dremel 3D20 is intended for 3D printing objects

from digital les that you create or own, or have the

right to print using the Dremel 3D20. When making

objects using the Dremel 3D20, it is your responsibility

to ensure that you do not infringe any third party

intellectual property rights or violate any applicable

laws or regulations, such as U.S. or foreign intellectual

property laws. The Dremel 3D20 may not be used to

make objects protected by intellectual property rights

owned by third parties without such third parties’

permission. Using the Dremel 3D20 to do any of the

following may require the permission of third parties:

to make a duplicate or facsimile (in whole or in part) of

any object not created by you, to make an object from

a digital le you do not own, or to make an object from

a scan of a physical object that you did not create. It is

your responsibility to obtain such permission. In some

cases, you may not be able to obtain such permission.

Where such permission cannot be obtained, you

should not 3D print such object, or you do so at your

own risk. You may not modify, reverse engineer,

decompile, or disassemble the Dremel 3D20 or its

software or rmware, except as permitted by applicable

law. If you use the Dremel 3D20 in any way other than

as recommended and described in these Operating/

Safety Instructions, you do so at your own risk. Using

the Dremel 3D20 to make objects that infringe any

intellectual property rights owned by third parties could

result in civil or criminal prosecution and penalties,

and you could be liable for money damages, nes, or

imprisonment.

3

FUNCTIONAL DESCRIPTION AND

SPECIFICATIONS

BUILDING

Extruder: Single extrusion

Extruder temperature: Up to 230°C (397°F)

Operating Interface: 3.5” full colour IPS touch screen

Maximum Build Volume: 9” x 5.9” x 5.5”

(230mm x 150mm x 140mm)

Layer Thickness: 4 mil | 0.004 inches 100 microns |

0.10 mm

Filament colours: See Dremel3D.com for colour

choices

SD Card: Up to 32GB in size (3D20 will not work with

SD cards larger than 32GB)

Internal Storage: 4GB

WEIGHT & DIMENSIONS

Weight (without spool): 8.8kg (19lbs 8oz)

Dimensions: 19.1” x 15.7” x 13.2” (485mm x 400mm

x 335mm)

FILAMENT

ONLY works with Dremel PLA lament

Filament: 1.75mm PLA

(Biodegradable/Renewable)

FILAMENT STORAGE

All polymers degrade with time. Do not unpack until

lament is needed. Filament should be stored at room

temperature: 16-29° C (60-85° F)

SOFTWARE

Dremel 3D20 comes with complimentary Dremel 3D

software for Windows and Mac OSX. This application

converts your 3D digital les into buildable les.

MINIMUM HARDWARE REQUIREMENTS

A PC with these minimum requirements will be required

to run the Dremel

®

3D Software

Processor: Multi-core processor - 2 GHz or faster per

core

System RAM: 2 GB

Screen Resolution: 1024x768

USB port

WINDOWS REQUIREMENTS

Dremel

®

Software runs on 32 and 64-bit Operating

Systems

Windows Vista or later

MAC OSX REQUIREMENTS

Dremel

®

Software runs on Mac OSX 10.8 or later

ELECTRICAL REQUIREMENTS

3D20 input rating: 220-240V~, 50/60Hz, 0.65A

OPERATING ENVIRONMENT

Room Temperature: 16-29° C (60 - 85° F)

Level workspace

Dry workspace environment

WALL

15.7” (400mm)

19.1” (485mm) 13.2” (335mm)

8” (203mm)

8” (203mm)8” (203mm)

14” (356mm)

4

3D20 RESOURCES

Resource Description Location

Quick Start

Guide

Provides

illustrated walk

through of how to

un-box your 3D20

and start building

out of the box.

Printed version of

the Quick Start

Guide is located

in the rectangular

component carton.

It is also available

on www.dremel3d.

com

3D20 Website Provides the

latest 3D20

software, product

information, and

customer support.

www.dremel3d.com

3D20

Customer

Support

Contact Dremel

for product

support,

maintenance, and

service.

Dremel 3D20

Software

Allows you to

upload, edit, and

build 3D les.

You can also

change device

settings and order

supplies.

Installed from

www.dremel3d.com

or from SD card

provided with the

Dremel 3D20.

GLOSSARY OF TERMS

Term Denition

Build Platform The at surface used by your Dremel

3D20 to build objects.

Build Platform

Clip

Clip located at the front of the build

platform base that is used to secure

the build platform in place.

Build Tape Adhesive tape similar to blue painter’s

tape that improves the consistency of

your objects and helps them stick to

the build plate surface.

Build Volume The three dimensional (3D) amount

of space that an object will use once

it is completed. Your Dremel 3D20

has a maximum build volume which

means that objects with a larger build

volume cannot be built unless they

are resized or broken into sub-objects.

Door Your Dremel 3D20 has a door located

on the front panel. This allows for

easy access to the build platform,

extruder, lament, and your objects.

This door is made with a transparent

material so you can monitor the

progress of your objects while keeping

the build environment stable.

Lid Your Dremel 3D20 has a removable

lid on the top. This allows for more

access to the build platform, extruder,

lament, and objects when necessary.

Limit Switch Switch that is activated by the motion

of the extruder or build platform when

the end of travel is reached.

Extruder An assembly that uses gears to

pull lament through the extruder

intake, heat the lament to the build

temperature, and push the heated

lament out of the extruder tip.

Extruder Fan A fan used to cool the outer assembly

of the extruder and gear motor.

Extruder Intake An opening located at the top of the

extruder where lament is inserted for

building.

Extruder Push

Lever

A lever located on the side of the

extruder that is used to loosen the

grip of the extruder gear motor.

Extruder Tip A nozzle located at the bottom of the

extruder where heated lament is

forced out for building.

Filament A threadlike strand of plastic material.

Filament Spool A cylindrical piece on which a long

strand of lament is wound for storage

and continuous use.

Filament Guide

Tube

A plastic piece that guides the

lament from the lament spool

through a passage in the outer

housing of your Dremel 3D20.

Levelling

Knobs

Knobs located under the build

platform base that are used to create

proper spacing between the extruder

tip and the build platform.

Levelling Tool Calibrated levelling pad with detailed

markings and directions for use.

5

PLA A bio plastic derived from renewable

resources such as corn starch.

Needle Nose

Pliers

Common tool used to hold small

objects and to grab excess material

that may be too hot to touch directly.

Object

Removal Tool

A tool used to separate your objects

from the build platform.

SD Card A portable memory card used on

a wide array of devices such as

cameras.

Spool Holder A plastic piece located to the left of

the build platform inside your Dremel

3D20 build area that is designed to

hold a lament spool.

Spool Lock A plastic piece which locks the

lament spool to the spool holder.

This piece is inserted through the

centre of the lament spool, into the

spool holder, and turned to lock.

Stepper Motor A brushless DC electric motor used

to drive the guide rails and extruder

gears.

.STL File A common digital le format used in

a wide range of 3D model software.

This le is created in 3rd party

3D software or downloaded from

Dremel3D.com.

.3dremel File Dremel’s digital le format that is used

by your Dremel 3D20 to properly

process models.

.G3Drem File A buildable le format compatible with

your Dremel 3D20.

Touch Screen Full colour display that is touch

activated. It allows you to monitor

your Dremel 3D20 and objects while

also providing commands directly to

your Dremel 3D20 without the use of

a computer.

Unclog Tool A tool used to clear the extruder of

excess debris.

X-Axis Guide

Rails

A set of rails on either side of the

extruder that allow a stepper motor to

move the extruder to the left or right

side of the build area.

Y-Axis Guide

Rails

A set of rails on either side of the

build area that allow a stepper motor

to move the extruder to the front or

back of the build area.

Z-Axis Guide

Rails

A set of rails located at the back of

the build area that allow a stepper

motor to move the build platform up

or down.

6

GETTING TO KNOW YOUR 3D20

1. Lid

2. Door

3. Touch Screen

4. Build Platform

5. Build Platform Clips

6. Filament Spool

7. Filament Spool Holder/Lock

8. Extruder Tip

9. Extruder Fan

10. Extruder

11. Extruder Entry

12. X-Axis Guide Rails

13. Stepper motor (1 of 3)

14. Z-Axis Guide rail

15. Filament Guide Tube

16. Y-Axis Guide Rails

17. SD card Input

18. USB Input

19. Power Switch

20. Power Input

7

8

INTRODUCTION

Welcome to the world of Dremel 3D. Our mission is

to mentor you through the 3D building process and

share best practices for bringing your ideas to life. 3D

building is a process that will involve experimentation

and persistence. Thankfully, the Dremel experts are

here to make your job easier with online tips and live

support. Kick-start your success by registering your

Dremel 3D20 on Dremel3D.com giving you access

to hundreds of high-quality models and innovative

projects. With Dremel, you can build on your own

ideas, build them better and make them yours.

KIT CONTENTS AND UNPACKING

KIT CONTENTS

• Dremel 3D20

• 1 Filament Spool

(Do not store in moist or hot environment)

• Quick Start Guide

• Instruction Manual

• Power Cable

• USB Cable

• SD Card

(Containing Sample Model Files)

• Build Tape

• Object Removal Tool

• Unclog Tool

• Levelling Tool

Levelling tool

9

UNPACKING

1. Place box on table and cut tape.

2. Lift outer box and allow inner box to open.

3. Remove carton lid from top of your Dremel 3D20

4. Rectangular carton on top of your Dremel 3D20

contains product manual, quick-start guide, and

set-up pieces. Remove the kit contents located

inside.

5. Using a rm grip, lift your Dremel 3D20 out of

packaging and place gently on stable work surface.

6. Remove plastic lid from top of your Dremel 3D20.

7. Remove tape from your Dremel 3D20 door.

8. Remove inserts from inside of your Dremel 3D20.

Tip: Keep packaging for future transportation

and storage.

10

TOUCH SCREEN

Using your Dremel 3D20 without a computer is easy with the onboard software and full colour touch screen.

Before building your model we want to familiarize you with the touch screen menu structure and options.

!

WARNING

OBSERVE ALL PROVIDED WARNINGS AND SAFETY INSTRUCTIONS WHEN USING THE

DREMEL 3D20. FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,

PROPERTY DAMAGE OR PERSONAL INJURY.

BUILD

Select a model le from your Dremel 3D20‘s

onboard memory by tapping the Dremel 3D20

icon or select a model le from SD card by

tapping the SD card icon.

After a model is selected, a pop-up window will

appear on the touch screen with the following

options:

BUILD

Tapping this option will begin the building

process while displaying useful information and

object status.

STOP – Tapping this option will cancel the

object.

You will be asked whether to cancel building or

continue building.

PAUSE – Tapping this option will pause the

building process. This will allow you to access

the “Tools” menu to unload or load lament.

PLAY – Tapping this option will exit the pause

mode and resume building your object.

11

COPY

Tapping this option will allow you to copy a

model le from an SD card to your Dremel 3D20

onboard memory. You cannot copy a model le

from your Dremel 3D20 to an SD card.

COPY MODEL

Tapping this option will conrm your decision to

copy your model le from your Dremel 3D20’s

onboard memory or an SD card.

COPY MODEL SUCCESSFUL

A pop-up alert notifying you that the model le

has been successfully copied.

DELETE

Tapping this button to permanently delete the

selected model le from the onboard Dremel

3D20 memory drive or an SD card.

DELETE MODEL

A pop-up will ask you to conrm that you want to

permanently delete a model le from your

Dremel 3D20’s onboard memory or an SD card.

DELETE MODEL SUCCESSFUL

A pop-up alert notifying you that the model le

has been successfully deleted.

12

RETURN

Return to previous menu.

TOOLS

FILAMENT

Load – Tapping this option will instruct your

Dremel 3D20 to begin heating the extruder for

loading lament (see page 19 for instructions

on loading lament). The touch screen will

display a status bar and will let you know when

it is time to load the lament.

Unload - Tapping this option will instruct your

Dremel 3D20 to begin heating the extruder

for unloading lament (see page 23 for

instructions on unloading lament). The touch

screen will display a status bar and will let you

know when it is time to unload the lament.

13

LEVEL

Tapping this option will begin the build platform

levelling process (see page 20 for instructions

on levelling the build platform). The touch screen

will display instructions on how to level the build

platform.

HOME

Tapping this option moves the extruder and build

platform to the zero position.

JOG MODE

Tapping this option will display the options for

positioning the extruder and build platform along

the X-axis, Y-Axis, and Z-axis.

14

SETTING

Tapping this option will allow you to change the

manufacturer settings for language or revert

back to manufacturer settings.

PREHEAT

Tapping this option will begin preheating the

extruder for building or excess debris removal.

The touch screen will display the approximate

extruder temperature. You can use the touch

screen to START or STOP the preheating

process at any time.

ABOUT

Tapping this option will display your Dremel

3D20 serial number, current rmware version,

usage (hours), and the Dremel 3D20 status.

15

RETURN

Return to previous menu.

SOFTWARE INSTALL AND

REGISTRATION

Creating an account on Dremel3D.com is easy and

gives you access to all of the great designs and

collections that will drive and inspire your creativity.

INSTALLING SOFTWARE FROM DREMEL3D.COM

1. Go to Dremel3D.com.

2. From a PC: Download and install software onto

your PC.

a. Download the Dremel 3D software from

Dremel3D.com.

b. Click on Dremel 3D_(version number).exe in the

folder location that you downloaded the le. The

install wizard will open.

c. Follow the prompts in the install wizard to load

the software on your computer.

3. From a MAC: Download and install software onto

your MAC.

a. Click Downloads and select Dremel 3D software.

Double click on the zip le and the Dremel 3D

INSTALLER.DMG will appear.

b. Double click on Dremel 3D INSTALLER.DMG to

make a new window open. Drag the install le to

the APPLICATIONS folder.

c. If the “Drag to Install” window did not open,

locate the Dremel 3D driver in you device panel.

Click on Dremel 3D to download software.

NOTE: Safari users will not have to unzip the

INSTALLER.DMG le.

d. Click NEXT to launch the setup wizard. The

Dremel 3D software setup wizard will guide

you through the steps to install the software on

your computer. Click NEXT to launch the setup

wizard.

4. Create Dremel maker account on Dremel3D.com to

begin downloading Dremel 3D20 models.

CONNECTING USB CABLE

1. Ensure power switch is in the off position.

2. Plug your Dremel 3D20 into the computer with the

USB cable.

3. Open software.

4. Turn your Dremel 3D20 on using the power switch

to sync your computer to your Dremel 3D20.

16

DREMEL SOFTWARE OVERVIEW

TOOLBAR ICONS

The toolbar icons in the Dremel 3D Software lets you

load, share, build, view, move, rotate, and scale your

objects.

Load – Click on “Load” and select a le from the

model les downloaded from Dremel3D.com. The

model that you selected will appear on the Dremel

3D20 home screen. The software’s home screen is a

simulation of your Dremel 3D20’s build platform.

3D Store – Clicking on “3D Store” will connect you to

Dremel3D.com with your default internet browser.

Build – Dremel 3D Software gives you the ability

to select build quality settings. This allows you to

customize both the build quality and build time.

a. Export Option – Saves your model le to local

drive or portable memory drive for building later.

b. Resolution Options – Models set to Standard

resolution will be built using the default settings.

“Standard” resolution builds will build quickly and

have good surface quality. Models set to “Fast”

resolution will be built with thicker layers and will

build faster. Models set to “Detailed” resolution

will have ner layers and will build more slowly.

c. Support – Select this checkbox to have your

object built with support structures. Dremel

3D20 software will automatically generate

supports for any overhanging sections of your

object. Supports will be easily removable once

your nished object is removed from the build

platform.

View – Changes your view of the Dremel 3D20 home

screen to one of six viewing angles.

TIP: You can view the Dremel 3D20 home screen

from any angle by holding the right click button of your

mouse and moving the mouse. You can also use your

mouse wheel to zoom in and out.

Move – Change your object location on the build

platform using X, Y, and Z axis positioning. You can

also centre your object in the build area and ensure

that your object is located on the platform. You can

choose to enter a custom axis position value.

X

Moves the model to the left or right side of

the build area.

Y

Moves the model to the front or back side of

the build area.

Z

Moves the model up and down in relation to

the build platform.

a. On Platform – Places the model onto the build

platform.

b. Centre – Centre’s the model on the 3D build

area.

c. Reset – Resets the model position to the

original position.

Rotate – Changes the orientation of your object on

the build platform using X, Y, and Z axis positioning.

You can choose to rotate your object +/- 90 degrees or

enter a custom axis position value. You can reset the

model to the original orientation.

Scale – Change the size of your object on the build

platform using X, Y, and Z positioning. You can choose

STATUS : PRINTING

MOVE

ROTATE

SCALE

IDEA BUILDER

VIEW

BUILD

LOAD

3D ONLINE

FILE EDIT BUILD VIEW TOOLS HELP

1

3 2

17

to enter a custom scale value in X,Y, and Z. You can

also increase the size of your object by a percentage

of its original design.

X

Rotates the model towards or away from the

front of the build area.

Y

Rotates the model towards the left or right

side of the build area.

Z

Rotates the model clockwise or counter

clockwise in the build area.

a. Maximize - Uniformly scale the model to the

largest size possible for building.

b. Reset – Undo all scale changes. Model reverts

back to original size.

TIP: If your object was designed in using inches

(Imperial Units), you can convert to mm (metric) units

by increasing your object by 2540%.

Idea Builder – Check the status of your Dremel 3D20.

As long as your Dremel 3D20 is connected to your

computer you can see whether your Dremel 3D20 is

ready to build or currently building an object. You can

also see the temperature of your extruder.

BUILD STATUS

Dremel 3D software continuously provides you with the

status of your Dremel 3D20.

a. The top panel displays the current status of both

your Dremel 3D20 and your object.

b. The status circle located in the top right corner

provides a graphical representation of your

progress.

MENUS

File Menu

a. Load File – Select this option to load a model le

(.STL or .3dremel) from your computer or external

storage device connected to your computer. Once

you have loaded the model le you can begin

editing the le as desired.

NOTE: You cannot load a model le to your

computer from an SD card connected to your

Dremel 3D20. SD card must be connected direct ly

to your computer.

b. Save Build Platform – Saves all of the objects

and layout of the current build platform to a

.3dremel le. Select this option to save a model

le to your computer or external storage device

connected to your computer.

NOTE: You cannot save a model le to an SD card

connected to your Dremel 3D20. SD card must be

connected directly to your computer.

c. Save as… - Saves current build platform with new

name. This will not overwrite the original .3dremel

le.

d. Examples – Select this option to view a list of

free model les that are included with your Dremel

3D software. These model les are excellent test

objects to ensure your Dremel 3D20 is working

properly.

e. Recent Files – Select this option to view a list of

recently viewed model les.

f. Preferences – Select this option to set the

language of your Dremel 3D software and change

the automatic update setting.

g. Quit – To close the Dremel 3D software, click on

the “X” in the upper right corner. If you have a

model le open the software will ask you if you

want to save your model le before closing.

Edit Menu

a. Undo – Select this option to undo the most recent

edit you made to your model le. Selecting this

option multiple times will continue to undo edits in

reverse order in which they were performed.

b. Redo – Select this option to redo the most recent

edit you have undone to your model le. Selecting

this option multiple times will continue to redo edits

in reverse order in which they were removed.

c. Select All – Select this option to select all of the

model les that you have loaded to the 3D Build

Home Screen.

d. Duplicate – Select this option to duplicate a

selected model le.

e. Delete – Select this option to delete a selected

model le.

Build Menu

NOTE: The power to your Dremel 3D20 must be

turned on for your Dremel 3D20 to be recognized.

a. Disconnect – Select this option to disconnect your

Dremel 3D20 from your computer.

b. Build – Select this option to convert your work to a

buildable le. You will be asked to save your model

in a .3dremel le format so that your Dremel 3D20

can begin building.

View Menu

a. Change your view of the 3D Build home screen to

one of seven viewing angles.

b. Show Model Outline – This view will highlight the

outer surfaces of your model le to improve viewing

of your model.

c. Show Steep Overhang – This view will highlight

areas of your object that have steep angles that

may require supports.

Tools Menu

a. Control Panel – Select this option for manual

diagnostics of your Dremel 3D20. Your Dremel

3D20 must be connected to your computer to view

this menu.

b. Update Firmware – Allows you to update your

Dremel 3D20 with the latest rmware. To update

the Dremel 3D20 rmware, connect a USB cord

to the computer and Dremel 3D20. Click the latest

version of the rmware and choose upload. The

rmware will update on the Dremel 3D20. After the

rmware has successfully updated, you need to

reboot (turn off and back on) the machine.

Note: Firmware updates will be automatically

downloaded when the Dremel 3D software is

started. You will be informed that a new version of

the rmware is available.

Help Menu

a. Help Contents – Select this option to be directed

to www.Dremel3D.com help and support contents.

b. Check for Update – Select this option to manually

check for Firmware and Software updates.

c. About – Select this option to review the current

software version you are running for Dremel 3D.

18

GETTING READY TO BUILD

!

WARNING

OBSERVE ALL PROVIDED

WARNINGS AND SAFETY

INSTRUCTIONS WHEN USING THE DREMEL 3D20.

FAILURE TO DO SO MAY RESULT IN FIRE,

EQUIPMENT DAMAGE, PROPERTY DAMAGE OR

PERSONAL INJURY.

1. Ensure the power switch is in the off position.

2. Remove the Dremel 3D20 lid for better access to

extruder and build platform.

3. If build platform is installed, remove by pinching the

clamp located at the front of the build platform and

lifting the build platform off the base.

PRESS

LEFT

4. Mount lament spool to spool holder and secure

with spool lock.

a. Place lament spool onto spool holder with

spool being fed from the bottom towards the

back of the Dremel 3D20.

End of lament

b. Insert spool lock into spool holder and rotate 90

degrees to lock in place.

5. Thread lament through lament guide tube. The

lament can then be inserted into the extruder

intake (Manual Image 11). This will ensure the

extruder experiences minimal resistance while

building.

Filament guide

6. Place Build Tape over Build Platform.

7. Install the build platform using the build platform

clip to secure.

8. Plug power cord into outlet and turn on Power

Switch (Dremel 3D20 will take approximately

30 seconds to properly warm up).

9. Tap “Tools” on your Dremel 3D20’s touch screen

then tap “Filament”, then tap “Load Filament”.

10. Insert the lament coming from the lament guide

tube into the extruder intake (top). Tap “Next”.

19

11. Your Dremel 3D20 will begin to heat the extruder.

The Dremel 3D20 touch screen display will update

you when extruder is “HOT” and ready to load.

12. Once your Dremel 3D20 is ready to begin

extruding, gently guide the lament into the

extruder until it feeds through on its own.

!

WARNING

DO NOT TOUCH THE EXTRUDER

TIP DURING DREMEL 3D20

OPERATION OR UNTIL IT HAS COOLED DOWN TO AT

LEAST 60°C (140°F). CONTACT WITH THE EXTRUDER

TIP DURING OR AFTER OPERATION BEFORE TIP

HAS COOLED MAY RESULT IN PERSONAL INJURY.

13. Filament will then be drawn into the extruder and

begin to exit from the heated tip at the bottom of

the extruder. After the lament has extruded from

the heated tip, press the return arrow to complete

the loading process. Carefully remove excess

lament without touching the hot extruder tip.

NOTE: Your Dremel 3D20 was tested by building

objects before leaving the factory. These test

objects may have been made with a different

lament colour than you are using. Therefore, a

small amount of lament may be remaining in the

extruder. When loading lament for the rst time

make sure to allow lament to exit the extruder

until your lament colour is consistently visible.

CAUTION: Use extra care to not damage the

extruder tip when clearing debris. Dremel 3D20 will

not work properly with damaged extruder tip and

will require replacement.

14. After lament has been loaded, ensure the extruder

tip is clear of any debris. Carefully remove debris

with needle nose pliers to ensure the extruder tip

is clean.

15. If lament does not get pulled into the extruder or

does not come out of the extruder tip, tap “Cancel”.

Tap “Setup” then tap “Unload Filament”. Once your

Dremel 3D20 alerts you it is ready, gently remove

the lament from the top of the extruder and repeat

the lament installation steps above. Reference

troubleshooting section for further advice.

BUILD PLATFORM PREPARATION

!

WARNING

DO NOT TOUCH THE EXTRUDER

TIP DURING DREMEL 3D20

OPERATION OR UNTIL IT HAS COOLED DOWN TO

60°C (140°F). CONTACT WITH THE EXTRUDER TIP

DURING OR AFTER OPERATION BEFORE TIP HAS

COOLED MAY RESULT IN PERSONAL INJURY.

CAUTION: Before every build make sure that the build

platform is covered with Dremel specied build tape.

Use of improper build tape may result in equipment

damage and poor object build quality.

LEVELLING BUILD PLATFORM

It is important you level the build platform every time

you replace the build tape or reinstall the build platform

to ensure that the build platform is evenly spaced

from the extruder head. Make sure to remove any air

bubbles from between the build platform and the build

tape. Not levelling the build platform or eliminating air

bubbles may cause objects to not build properly.

Wait for the extruder head to cool to at least 60C

(140F) before levelling build platform. Extruder

temperature can be monitored on the touch screen.

(See page 11.)

1. Make sure you have placed build tape over the

build platform. Applying build tape to the build

platform after levelling may affect the consistency

of your object.

2. Tap “Tools” on your Dremel 3D20’s touch screen

and tap “Level”. (See page 14.)

3. The extruder and build platform will move into

position to level the build platform. You will rst

level the front left section of the build platform. The

three knobs under build platform are used to raise

or lower the build platform on the left, right, and

rear of the build platform.

4. Place the levelling tool between the extruder and

build platform. If the levelling tool cannot slide

between the extruder and build platform, adjust

the appropriate knob (turning counter clockwise)

until you can slide the levelling tool between the

extruder and build platform with some resistance.

If the levelling tool can slide between the extruder

and build platform too easily, adjust the appropriate

knob (turning clockwise) until you can slide the

levelling tool between the extruder and build

platform with some resistance.

20

Sivu latautuu ...

Dremel 3D20 Idea Builder Original Instructions Manual

Dremel 3D20 Idea Builder Original Instructions Manual

muilla kielillä

Liittyvät paperit

Muut asiakirjat