Yamaha RX-V765 Omistajan opas

RX-V765

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

E

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press AMAIN ZONE ON/OFF

to set this unit in the standby mode, and disconnect the AC

power plug from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

...... AC 110/120/220/230–240 V, 50/60 Hz (General model)

..........................AC 220/230–240 V, 50/60 Hz (Asia model)

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by AMAIN ZONE ON/

OFF. In this state, this unit is designed to consume a

very small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Caution-ii En

Caution: Read this before operating your unit.

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in

the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or

http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical

and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/

EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

1 En

English

INTRODUCTION

APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

About this manual................................................... 3

Supplied accessories................................................3

Part names and functions....................................... 4

Front panel ................................................................. 4

Rear panel .................................................................. 5

Front panel display..................................................... 6

Remote control........................................................... 7

Quick start guide.....................................................8

L

Preparing remote control ....................................... 9

Installing batteries in the remote control ................... 9

Using the remote control............................................ 9

Connections ...........................................................10

Placing speakers....................................................... 10

Connecting speakers ................................................ 11

Information on jacks and cable plugs ...................... 14

Connecting a video monitor..................................... 15

Connecting other components ................................. 16

Connecting a multi-format player or an external

decoder................................................................. 18

Connecting an external amplifier............................. 18

Using REMOTE IN/OUT jacks............................... 19

Connecting a Yamaha iPod universal dock or

Bluetooth™ wireless audio receiver.................... 19

Connecting a camcorder or portable audio player ... 19

Connecting the FM and AM antennas ..................... 20

Connecting the power cable..................................... 20

Turning this unit on and off ..................................... 20

Optimizing the speaker setting for your

listening room (YPAO) ..................................... 21

Using Auto Setup..................................................... 21

When an error message is displayed during

measurement ........................................................ 23

When a warning message is displayed after

measurement ........................................................ 23

Playback.................................................................24

Basic procedure........................................................ 24

Using the SCENE function ...................................... 24

Muting audio output temporarily (MUTE).............. 25

Adjusting high/low frequency sound

(tone control) ....................................................... 25

Enjoying pure hi-fi sound (Pure Direct mode) ........ 25

Using your headphones............................................ 26

Displaying input signal information ........................ 26

Changing information on the front panel display .... 26

Enjoy the sound field programs .......................... 27

Selecting sound field programs................................ 27

Enjoying unprocessed input sources

(Straight decoding mode) .................................... 30

Enjoying sound field programs without surround

speakers (Virtual CINEMA DSP) ....................... 30

Enjoy sound field programs with headphones

(SILENT CINEMA™) ........................................ 30

Enjoying more spatial sound fields

(CINEMA DSP 3D mode)................................... 30

FM/AM tuning ......................................................31

Tuning into the desired FM/AM station

(Frequency tuning mode)..................................... 31

Registering FM/AM stations and tuning in

(Preset tuning mode)............................................ 31

Radio Data System tuning ................................... 33

Displaying the Radio Data System information ...... 33

Selecting the Radio Data System program type

(PTY Seek mode) ................................................ 33

Using the enhanced other networks (EON) data

service.................................................................. 34

Using iPod™.......................................................... 35

Controlling iPod™................................................... 35

Using Bluetooth™ components ........................... 37

Pairing the Bluetooth™ wireless audio receiver

and your Bluetooth™ component........................ 37

Playback of the Bluetooth™ component ................. 37

Other functions ..................................................... 38

Using the sleep timer ............................................... 38

Using the HDMI™ control function........................ 38

Setting the option menu for each input source

(OPTION menu) ............................................... 39

OPTION menu items ............................................... 39

Outputting a video signal input from another

input source during reproducing a multi-channel

audio signal.......................................................... 41

Editing surround decoders/sound field

programs ........................................................... 42

Setting sound field parameters................................. 42

Sound field parameters ............................................ 42

Changing various settings of this unit

(SETUP menu) .................................................. 46

Basic operation of the SETUP menu ....................... 47

Speaker Setup .......................................................... 47

Sound Setup ............................................................. 49

Function Setup ......................................................... 50

DSP Parameter ......................................................... 52

Memory Guard......................................................... 52

Using multi-zone configuration ........................... 53

Connecting Zone2.................................................... 53

Controlling Zone2.................................................... 54

Controlling other components with the remote

control................................................................ 55

Setting remote control codes.................................... 55

Programming from other remote controls ............... 56

Resetting all remote control codes........................... 57

Advanced setup..................................................... 58

Troubleshooting.................................................... 60

General..................................................................... 60

HDMI™................................................................... 63

Tuner (FM/AM) ....................................................... 64

Remote control......................................................... 64

iPod™ ...................................................................... 65

Bluetooth™.............................................................. 66

Auto Setup (YPAO)................................................. 66

Glossary ................................................................. 69

Sound field program information ....................... 71

Information on HDMI™...................................... 72

Specifications......................................................... 73

Index ...................................................................... 74

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

APPENDIX

List of remote control codes...................................i

2 En

INTRODUCTION

■ Built-in 7-channel power amplifier

• Minimum RMS Output Power (20 Hz-20 kHz, 0.08%

THD, 8 Ω)

• FRONT L/R: 95 W + 95 W

• CENTER: 95 W

• SURROUND L/R: 95 W + 95 W

• SURROUND BACK L/R: 95 W + 95 W

■ Speaker/Preout outputs

• Speaker jacks (7-channel + presence 2-channel), preout

output jacks (7-channel, and subwoofer preout jack x 2)

■ Input/Output terminals

Input terminals

• HDMI input x 4

• Audio/Video input

[Audio] Digital input (coaxial) x 2, digital input

(optical) x 2, analog input x 2

[Video] Component video x 2, S-video x 1,

composite video x 4

• Audio input (analog) x 2

• Phono input x 1

• Multi-channel audio input x 1

• Dock input x 1

• V-AUX input

[Audio] Analog x 1, stereo mini jack x 1

[Video] Composite video x 1

Output terminals

• Monitor output

[Audio/Video] HDMI x 1

[Video] Component video x 1, Composite video x 1

• Audio/Video output

[Audio] Analog x 1

[Video] Composite video x 1

• Audio output

Analog x 1

• Zone2 output

Analog x 1

Other terminals

Remote input x 1, Remote output x 1

Trigger output x 1

■ Proprietary Yamaha technology for the

creation of sound fields

• CINEMA DSP 3D

• Compressed Music Enhancer mode

• Virtual CINEMA DSP

• SILENT CINEMA™

■ Digital audio decoders

• Dolby TrueHD, Dolby Digital Plus

• DTS-HD Master Audio, DTS-HD High Resolution

Audio, DTS Express

• Dolby Digital, Dolby Digital EX

• DTS, DTS 96/24, DTS-ES Matrix 6.1,

DTS-ES Discrete 6.1

• Dolby Pro Logic, Dolby Pro Logic II,

Dolby Pro Logic IIx

• DTS NEO:6

• DSD

■ Sophisticated FM/AM tuner

• 40-station random and direct preset tuning

• Automatic preset tuning

• Radio Data System tuning

■

HDMI™

(High-Definition Multimedia Interface)

• HDMI interface for standard, enhanced or high-

definition video as well as multi-channel digital audio

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission

capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

• Analog video to HDMI digital video up-conversion

(composite video → HDMI, component video →

HDMI) capability for monitor out

• Analog video input up-scaling for HDMI digital video

output 576i or 576p → 720p, 1080i or 1080p

• HDMI control capability

■ DOCK jack

• DOCK jack to connect a Yamaha iPod universal dock

(such as YDS-11, sold separately) or Bluetooth wireless

audio receiver (such as YBA-10, sold separately)

■ Automatic speaker setup features

• “YPAO” (Yamaha Parametric Room Acoustic

Optimizer) for automatically optimizing speaker

outputs suitable for listening environments

■ Other features

• 192-kHz/24-bit D/A converter

• OSD (on-screen display) menus that allow you to

optimize this unit to suit your individual audiovisual

system

• Pure Direct mode for pure hi-fi sound for all sources

• Adaptive dynamic range controlling capability

• SCENE function that allows you to change input

sources and sound field programs with one key

• Sleep timer

• Multi-zone function

Features

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &

other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and DTS-

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other

countries.

Bluetooth™

Bluetooth is a registered trademark of Bluetooth SIG and is used by

Yamaha in accordance with a license agreement.

“HDMI,” the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

Check that you received all of the following parts.

• Remote control (see page 9)

• Batteries (AAA, R03, UM-4) x 2 (see page 9)

• Optimizer microphone (see page 21)

• AM loop antenna (see page 20)

• Indoor FM antenna (see page 20)

• Controls diagram

About this manual

• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between

the front panel and the remote control, the key name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of

differences between the manual and product, the product has priority.

• “AMAIN ZONE ON/OFF” or “eHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the

“Controls diagram” or “Part names and functions” on page 4 for the information about each position of the parts.

• y indicates a tip for your operation.

• ☞ indicates the page describing the related information.

Supplied accessories

4 En

A MAIN ZONE ON/OFF

Turns this unit on and off (see page 20).

B PHONES jack

For connecting headphones (see page 26).

C ZONE2 ON/OFF

Switches Zone2 between on and off (see page 54).

D HDMI THROUGH

During standby, lights up under the following conditions:

• the HDMI control function is enabled (see page 50).

• an HDMI signal input to this unit passes through this unit and

output (see page 50).

E ZONE2 CONTROL

Enables operation of a receiver set in Zone2, including input

source switching, volume control and tuner operation, with the

main amplifier or remote control after this key is pressed.

F INFO

Changes information on the front panel display, such as input

source and sound field program name (see page 26).

G MEMORY

Registers FM/AM stations as preset stations (see page 32).

H PRESET l / h

Selects an FM/AM preset station (see page 32).

I FM/AM

Changes the tuner bands between FM and AM.

J TUNING l / h

Changes FM/AM frequencies.

K Front panel display

Displays information on this unit (see page 6).

L VOLUME control

Controls the volume of this unit (see page 24).

M SCENE

Switches between linked sets of input sources and sound field

programs (see page 24).

N TONE CONTROL

Adjusts high-frequency/low-frequency output of speakers/

headphones (see page 24).

O PROGRAM selector

Changes sound field programs (see page 27).

P STRAIGHT

Toggles between the selected sound field program and straight

decoding mode (see page 30).

Q PURE DIRECT

Changes mode to Pure Direct mode (see page 25). This key

lights up when Pure Direct mode is on.

R INPUT selector

Selects an input source (see page 24).

S OPTIMIZER MIC jack

For connecting the supplied optimizer microphone and adjusting

output characteristics of speakers (see page 21).

T VIDEO (VIDEO AUX) jack

For connecting the video output cable of a camcorder or game

console (see page 19).

U AUDIO L/R (VIDEO AUX) jack

For connecting the audio output cable of a camcorder or game

console (see page 19).

V PORTABLE (VIDEO AUX) jack

For connecting the audio output cable of a portable music player

(see page 19).

Part names and functions

Front panel

TUNING

PHONES

SILENT

CINEMA

TONE

CONTROL

STRAIGHT

PROGRAM INPUT

PURE DIRECT

OPTIMIZER

MIC

VIDEO

AUDI O

PORTABLE

THROUGH

INFO

MEMORY

VIDEO

AUX

VOLUME

HDMI

EFFECT

PRESET

l

h

l

h

BD/DVD

TV

CD

RADIO

SCENE

ZONE2

ON/OFF

ZONE2

CONTROL

ON/OFF

FM AM

MAIN

ZONE

E

N Q SO R

D

K

C

L

GF JIH

M

U VTP

AB

5 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a DOCK jack

For connecting a Yamaha iPod universal dock (YDS-11, sold

separately) or a Bluetooth wireless audio receiver (YBA-10,

sold separately) (see page 19).

b PHONO jacks

For connecting a turntable (see page 17).

c ANTENNA jacks

For connecting supplied FM and AM antennas (see page 20).

d HDMI OUT/HDMI 1-4 jacks

For connecting an HDMI-compatible video monitor or external

components for HDMI inputs 1-4 (see page 16).

e REMOTE IN/OUT jacks

For connecting an external component that supports the remote

control function (see page 19).

f TRIGGER OUT jack

For connecting an external terminal with a trigger input terminal

to operate it linked with operation of this unit. For example,

when an electric screen that supports a trigger input is

connected, it opens and closes linked with operation of an input

source selected in this unit.

g SPEAKERS terminals

For connecting front right and left, center, surround and

surround back speakers (see page 11). Connect the presence

speakers (see page 12) or the speakers for Zone2 (see page 53)

to the EXTRA SP jacks.

h Power Cable

Connect this cable to an AC wall outlet (see page 20).

i AV 1-6 jacks

For connecting external components for audio/video inputs 1-6

(see page 16).

j AV OUT jacks

Outputs audio/video signals from a selected analog input source

to an external component (see page 17).

k AUDIO 1/2 jacks

For connecting external components for audio inputs 1-2

(see page 17).

l MONITOR OUT terminals

Outputs video signals from this unit to a video monitor, such as

a TV (see page 15).

m MULTI CH INPUT terminals

For connecting a player that supports a multi-channel output

(see page 18).

n AUDIO OUT jacks

Outputs audio signals from a selected analog input source to an

external component (see page 17).

o ZONE2 OUT jacks

Outputs sound of this unit to an external amplifier set in a

different zone.

p PRE OUT terminals

For connecting a subwoofer with built-in amplifier (see page 11)

or an external power amplifier (see page 18).

Rear panel

ZONE2

OUT

TRIGGER OUT

12V

0.1A MAX.

ANTENNAPHONO

UNBAL.

FM

GND

AM

COMPONENT

VIDEO

PR

PB

Y

IN

OUT

REMOTE

EXTRA SP

ZONE2

/

PRESENCE

MONITOR OUT

SPEAKERS

ZONE2

PR

PB

Y

OPTICAL

(

TV

)

A

V

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

S.VIDEO

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

FRONT

SURROUND

SUR. BACK

SUBWOOFER

PRE OUT

CENTER

VIDEO

HDMI

HDMI 1 HDMI 2 HDMI 3 HDMI 4

(

BD/DVD

)

VIDEO

COMPORNENT

VIDEO

FRONT

CENTER

SURROUND

SURROUND BACK/

BI-AMP

SINGLE

1

2

CENTER

OUT

DOCK

SINGLE

a

h

ij mknop

d

b

c

g

e f

l

6 En

Part names and functions

a HDMI indicator

Lights up during normal communication when HDMI is

selected as an input source.

b CINEMA DSP indicator

Lights up when a sound field program that uses CINEMA DSP

is selected.

c CINEMA DSP 3D indicator

Lights up when CINEMA DSP 3D is activated.

d Tuner indicator

Lights up during receiving radio broadcast signals from an FM/

AM station (see page 31).

e ZONE2 indicator

Lights up when Zone2 is turned on (see page 53).

f SLEEP indicator

Lights up when the sleep timer is activated (see page 38).

g MUTE indicator

Flashes when audio is muted.

h VOLUME indicator

Displays volume levels.

i Cursor indicators

Light up when corresponding cursors on the remote control are

available for operations.

j Multi information display

Displays menu items and settings for the current operation.

k Speaker indicators

Indicate speaker terminals from which signals are currently

output.

Front panel display

STEREO

SLEEP

VOL.

TUNED

PL PR

SW

C

LR

SL SR

SBL SB SBR

MUTE

3

ZONE

2

abcdfehg

ij ki

SW

C

LR

SL SR

SBL SB SBR

PL PR

Subwoofer

Front L

Surround L

Surround back L

Center

Front R

Surround R

Surround back R

Surround back

Presence L Presence R

7 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Remote control signal transmitter

Transmits infrared signals.

b MAIN/ZONE2

Switches the zone to be operated by the remote control between

the Main zone and Zone2 (see page 54).

c TRANSMIT

Lights up when a signal is output from the remote control.

d SOURCE POWER

Switches an external component on and off.

e Input selection keys

f Tuner keys

g INFO

Changes information on the front panel display, such as input

source and sound field program name (see page 26).

h Sound selection keys

Selects sound field programs (see page 27).

i SCENE

Switch between linked sets of input sources and sound field

programs (see page 24).

j SETUP

Displays the SETUP menu (see page 47).

k Cursors k / n / l / h/ENTER/RETURN

l External component operation keys

Operate recording, playback etc. of external components

(see page 55).

m Numeric keys

Enter numbers.

n TV control keys

Enable operations of a monitor such as a TV and a projector.

o CODE SET

Sets remote control codes for external component operations

(see page 55).

p POWER

Switches this unit on and standby.

q SLEEP

Switches the sleep timer operations (see page 38).

r OPTION

Displays the OPTION menu (see page 39).

s VOLUME +/–

Adjust the volume of this unit (see page 24).

t DISPLAY

Changes the operation mode of the iPod connected to the

Yamaha iPod universal dock (see page 35).

u MUTE

Turns the mute function of the sound output on and off

(see page 25).

Remote control

HDMI 1-4

Select HDMI inputs 1 through 4.

AV 1-6

Select AV inputs 1 through 6.

AUDIO 1/2

Select AUDIO inputs 1 and 2.

V-AUX

Selects the V-AUX jack on the front panel of this

unit.

MAIN

POWER

1234

1256

1234

7856

90

10

1234

POWER

SOURCE

V-AUX PHONO

[ A ] DOCK

MULTI

TUNER

FM

MOVIE

BD

DVD

TOP

MENU

MUSIC

SCENE

TV

CD

OPTIONSETUP

RETURN

REC

ENT

POWER

TV

TV VOL

INPUT

MUTE

TV CH

ENTER

VOLUME

DISPLAY

MUTE

MENU

RADIO

STEREO

ENHANCER SUR. DECODE

PURE DIRECT

STRAIGHT

INFO

MEMORY

AM

PRESET

TUNING

SLEEP

HDMI

AV

AUDIO

ZONE2

TRANSMIT

CODE SET

a

b

c

d

q

p

e

h

i

j

r

s

t

m

n

o

f

g

u

l

k

PHONO

Selects a component such as a turntable that is

connected to the PHONO jack on the rear panel

as an input source.

[A]

To control external components using the

lExternal component operation

keys separately from operations of this unit

(see page 55).

DOCK

Selects a Yamaha iPod universal dock/Bluetooth

wireless audio receiver connected to the DOCK

jack.

TUNER

Selects the FM/AM tuner.

MULTI

Selects a signal input from the MULTI CH

INPUT jack on the rear panel as an input source.

FM

Select the FM band or AM band.

AM

MEMORY

Presets radio stations.

PRESET k / n

Select a preset station.

TUNING k / n

Change tuning frequencies.

Cursors k / n / l / h

Select menu items displayed on the

front panel display or on a video

monitor, or change settings.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen or

ends the menu display.

8 En

When you use this product for the first time, perform the steps below. See the related pages for details of operations and

settings.

Prepare speakers, DVD player, cables, and other items

necessary for setup.

For example, prepare the following items for setting up a

7.1-channel sound system.

y

• Prepare at least two (front) speakers. Speakers other than front speakers

may be used in the following order of preference:

1 Two surround speakers

2 One center speaker

3 One or two surround back speakers

• If your video monitor is a CRT, we recommend that you use magnetically

shielded speakers.

• An audio cable is not required when you use an HDMI cable.

Place your speakers in the room and connect them to this

unit.

y

• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)

that automatically optimizes this unit based on room acoustic

characteristics (audio characteristics of the speakers, speaker positions,

and room acoustics, etc.).

You can enjoy good balanced sound without special knowledge by using

the YPAO technology (see page 21).

Connect your TV, DVD player, or other components.

Connect the power cable and turn on this unit.

Select the component connected in the step 3 as an input

source and start playback.

y

• This unit supports the SCENE function that changes the input source and

sound field program at one time. Four SCENE are preset for different

purposes for Blu-ray disc, DVD and CD. You can select from a SCENE

from those just by pressing a remote control key. See page 24 for details.

Quick start guide

Step 1: Prepare items for setup

Requirements qty.

Speakers Front speaker 2

Center speaker 1

Surround speaker 2

Surround back speaker 2

Active subwoofer 1

Speaker cable 5

Subwoofer cable 1

Reproduction component such as DVD player 1

Video monitor such as TV 1

Video cable or HDMI cable 2

Audio cable 2

Components

(such as DVD player)

Center speaker

Front left speaker

Front right speaker

Subwoofer

Video monitor

Surround right speaker

Surround left speaker

Surround back right

speaker

Surround back left

speaker

Step 2: Set up your speakers

• Placing speakers ☞P. 1 0

• Connecting speakers ☞P. 1 1

Step 3: Connect your components

• Connecting a video monitor ☞P. 1 5

• Connecting other components ☞P. 1 6

• Connecting a multi-format player or an

external decoder ☞P. 1 8

• Connecting an external amplifier ☞P. 1 8

• Connecting a Yamaha iPod universal

dock or Bluetooth wireless audio receiver ☞P. 1 9

• Connecting the FM and AM antennas ☞P. 2 0

Step 4: Turn on the power

• Connecting the power cable ☞P. 2 0

• Turning this unit on and off ☞P. 2 0

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 2 4

• Selecting sound field programs ☞P. 2 7

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

PREPARATION

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows.

– the transmit indicator does not flash or is dim.

• Do not use old batteries together with new ones.

This may shorten the life of the new batteries or cause old batteries

to leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may be

different even though they look the same.

• If you find leaking batteries, discard the batteries immediately,

taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Dispose of the old batteries correctly in accordance with your local

regulations.

• If the remote control is without batteries for more than 2 minutes,

or if exhausted batteries remain in the remote control, the contents

of the memory may be cleared. In such a case, install new batteries

and set the remote control code.

The remote control transmits a directional infrared ray. Be

sure to aim the remote control directly at the remote

control sensor on this unit during operation.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

y

• You can operate external components with this remote control by setting

the remote control code. See page 55 for details.

Preparing remote control

Installing batteries in the remote

control

1

3

2

Using the remote control

30 30

Remote control sensor window

within 6 m

10 En

This unit supports up to 7.1-channel surround playback. We recommend the following speaker layout in order to obtain

the optimum surround effect.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

■ Front left and right speakers (FL and FR)

The front speakers output the front channel sounds (stereo

sound) and effect sounds. Place these speakers at an equal

distance from the ideal listening position. When using a

screen, the appropriate top positions of the speakers are

about 1/4 of the screen from the bottom.

■ Center speaker (C)

The center speaker outputs the center channel sounds

(dialog, vocals, etc.). Place it halfway between the left and

right speakers. When using a TV, place the speaker just

above or just under the center of the TV with the front

surfaces of the TV and the speaker aligned. When using a

screen, place it just under the center of the screen.

■ Surround left and right speakers (SL and SR)

The surround speakers output effect sounds and surround

sounds. Place them at the rear left and rear right facing the

listening position.

To obtain a natural sound flow in the 5.1-channel speaker

layout, place them slightly further back than in the 7.1-

channel speaker layout.

■ Surround back left and right speakers (SBL

and SBR) / Surround back speaker (SB)

The surround back left and right speakers output rear

effect sounds. Place them at the rear of the room facing the

listening position at least 30 cm away from each other,

ideally at the same distance as that between the front left

and right speakers.

In the 6.1-channel speaker layout, surround back left and

right channel sound signals are mixed down and output

from the single surround back speaker.

In the 5.1-channel speaker layout, surround back left and

right channel sound signals are output from the surround

left and right speakers.

■ Subwoofer (SW)

The subwoofer speaker outputs bass sounds and low-

frequency effect (LFE) sounds included in Dolby Digital

and DTS signals. Use a subwoofer with a built-in

amplifier, such as the Yamaha Active Servo Processing

Subwoofer System. Place it exterior to the front left and

right speakers facing slightly inward to reduce reflections

from a wall.

Connections

Placing speakers

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

SW

30 cm or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

SW

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Speaker channels

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

When you connect speakers, connect them to the respective jacks as follows, according to your speaker layout.

y

• You can connect up to two subwoofers. When two subwoofers are connected, the same sound is output from them.

■ 7.1-channel

■ 6.1-channel

■ 5.1-channel

Connecting speakers

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker L SURROUND

BACK/BI-AMP (L)

g Surround back speaker R SURROUND

BACK/BI-AMP (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

EXTRA

SP

ZONE2

/

2

PRESENCE

SPEAKERS

SUBWOOFER

FRONT

CENTER

SURROUND

SURROUND BACK/

BI-AMP

SINGLE

1

2

O

UT

.

EXTRA SP

ZONE2

/

2

PRESENCE

Z

O

NE2

ZONE2

R.BA

C

K

SU

BW

OO

FE

R

N

PUT

A

U

DI

O

OU

T

FR

O

N

T

S

URROUND

SUR. BAC

K

P

RE

O

UT

CENTER

C

ENTER

S

IN

G

LE

e d

b

a

g

f

c

h

i

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker SURROUND

BACK/BI-AMP (SINGLE)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

12 En

Connections

You can connect presence speakers (PL/PR) that output

front effect sounds to this unit. With CINEMA DSP sound

field programs (see page 27) and their CINEMA DSP 3D

functions, a sound with a richer and more spacial presence

can be created. You can adjust the vertical position of

center sound such as a dialog (see page 47).

To use the presence speakers, connect them to the EXTRA

SP jacks and set “Extra SP Assign” in “Speaker Setup” in

the SETUP menu to “Presence” (see page 47).

y

• Although you can connect both surround back speakers and presence

speakers to this unit, you cannot output sounds from those speakers at the

same time. This unit automatically selects speakers to output sounds

according to the selected input source and sound field program.

• You can connect Zone2 speakers with a multi-zone function to the

EXTRA SP jacks. For details, see page 53.

Presence speakers

FR

PRPL

C

FL

0.5 to 1 m0.5 to 1 m

1.8 m 1.8 m

EXTRA SP

ZONE2

/

PRESENCE

X

.

D

MI 3

HDMI 4

FR

O

N

T

C

ENTE

R

SU

RR

OU

N

D

SU

RR

OU

ND BA

C

K

/

B

I-AM

P

PR

PL

Presence

speaker L

Presence

speaker R

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

1 Remove approximately 10 mm of insulation

from the end of each speaker cable and then

twist bare wires of the cable together so that

they will not cause a short circuits.

2 Loosen the knob, insert the twisted bare

wires into the hole, and then tighten the

knob.

y

• You can connect the presence speakers (see page 12) or the speakers in

the second zone (Zone2) (see page 53) to the EXTRA SP jacks.

You can connect speakers that support bi-amplification

connections to this unit. To connect the speakers via a bi-

amp connection, connect them to the FRONT jacks and

SURROUND BACK/BI-AMP jacks as illustrated.

To enable the bi-amp connection, connect the power cable

to the wall outlet, display the ADVANCED SETUP menu

and set “BI AMP” to “ON” (see page 58).

Note

• You cannot use surround back speakers or extra speakers (presence and

Zone2 speakers) when bi-amplification connections are made.

Connecting the speaker cable

Caution

• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently

or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit

and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this

unit and the other end to that of your speaker.

• Before connecting the speakers, be sure to disconnect the power cable.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or

speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned

on.

• If your video monitor is a CRT, use magnetically shielded speakers. If images on the monitor are still distorted even

when you use the magnetically shielded speakers, place the speakers away from the monitor.

• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in “ADVANCED SETUP” before

connecting the speakers. You can also use 4-ohm speakers as the front speakers when you set “SP IMP.” to

“6ΩMIN” (see page 58).

Connecting the banana plug (Except U.K.,

Europe, Russian, Asia and Korea models)

Tighten the knob, and then insert the banana plug into

the end of the terminal.

10 mm

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Using bi-amplification connections

Caution

Before making bi-amplification connections, remove

any brackets or cables that connect a woofer with a

tweeter. Refer to the instruction manuals of speakers for

details.

When not making bi-amplification connections, make

sure that the brackets or cables are connected before

connecting the speaker cables.

FRONT

SURROUND BACK/

BI-AMP

SINGLE

Front speakers

Right Left

This unit

14 En

Connections

This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are

connecting.

■ Audio jacks

■ Video jacks

■ Video/audio jacks

y

• We recommend that you use a commercially available 19-pin HDMI

cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.

• If you connect this unit to a component that has a DVI jack, an HDMI/

DVI-D cable is required.

• You can check error information on HDMI connections (see page 72).

Information on jacks and cable plugs

Jack and cables Description

AUDIO jacks To transmit conventional analog

(stereo) signals. Use stereo pin

cables. Connect red plugs to red

jacks (R) and white plugs to white

jacks (L).

COAXIAL jacks To transmit coaxial digital audio

signals. Use pin cables for digital

audio signals.

OPTICAL jacks To transmit optical digital audio

signals. Use optical fiber cables for

optical digital audio signals.

Jack and cables Description

VIDEO jacks To transmit conventional

composite video signals. Use video

pin cables.

S VIDEO jack To transmit S-video signals that

include luminance (Y) and

Cameroonians (C) components.

Use S-video cables.

COMPONENT VIDEO

jacks

To transmit component video

signals that include luminance (Y),

chrominance blue (PB) and

chrominance red (PR) components.

Use component video cables.

AUDIO

L

R

(white)

(red)

COAXIAL

C

(orange)

OPTICAL

O

VIDEO

V

(yellow)

S VIDEO

S

PR

PB

Y

COMPONENT

VIDEO

P

B

Y

P

R

(red)

(blue)

(green)

Jack and cables Description

HDMI jacks To transmit digital video and

digital audio signals. Use HDMI

cables.

A video signal input to this unit is output from the jacks

in MONITOR OUT for the same kind of signal as the

input signal.

For example, if a VCR with a composite output signal

and a DVD player with a component video output

signal are connected, connect both VIDEO jack and

COMPONENT VIDEO jack in MONITOR OUT to the

video monitor.

If an HDMI input compatible monitor is connected, this

unit automatically converts an analog signal that is

input from a video input jack to a digital video signal,

and then outputs it from the HDMI OUT jack.

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

S VIDEO

Input Output

Not converted Converted

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Connect a video monitor such as a TV or projector to an output jack of this unit. You can select one of the following three

types according to the input signal format supported by the video monitor: HDMI OUT, COMPONENT VIDEO and

VIDEO (composite video).

Note

• Make sure that this unit and video monitor are unplugged from the AC wall outlets.

■ To connect an HDMI video monitor

y

• This unit supports the HDMI control function. By connecting a TV that

supports the HDMI control, operations of this unit can be controlled with

the remote control of the TV. For details, see page 38.

■ To connect component video monitor

Note

• Only video signals input from this unit via the COMPONENT VIDEO

jack are output from the COMPONENT VIDEO jack.

■ To connect composite video monitor

Note

• Only video signals input from this unit via the VIDEO jacks are output

from the VIDEO jacks.

To output sound of a TV from this unit, connect an audio

output terminal of the TV to any of the AV 1-6 jacks.

If the TV supports an optical digital output, we

recommend that you use the AV 1. Connecting to the AV 1

allows you to switch an input source to the AV input 1

with a just a single key operation using the SCENE

function (see page 24).

Note

• If the video monitor connected to this unit supports the HDMI control

function, we recommend that you connect its audio output jack to the

OPTICAL jack of the AV1 jacks of this unit. By doing so, this unit

automatically turns on and “TV” of SCENE is automatically selected

when you turn on the video monitor. You can obtain the same result even

if you connect the audio output jacks to the AV2-6, AUDIO1-2 or V-

AUX jacks by assigning those jacks to TV in advance (see page 24).

Connecting a video monitor

Jacks on components Jacks on this unit

a HDMI input HDMI OUT

Jacks on components Jacks on this unit

b Component video output MONITOR OUT

(COMPONENT VIDEO)

Jacks on components Jacks on this unit

c Video input (composite) MONITOR OUT (VIDEO)

P

R

P

B

Y

MONITOR OUT

HDMI

VIDEO

COMPORNENT

VIDEO

OUT

T

RIGGER OU

T

12

V

0

.1

A

MAX.

ANTENNA

P

H

O

N

O

UNBAL.

FM

G

ND

G

N

D

A

M

I

N

OUT

REM

O

TE

S

.VIDE

O

D

E

O

HDMI

1

HDMI

2

HDMI

3

(

B

D

/

DVD

)

V

c

b

P

B

YP

R

HDMI

a

TV or projector

Outputting sound of a TV from this unit

OPTICAL

(

TV

)

A

V

1

ANTENN

A

P

H

O

N

O

U

NBAL.

F

M

G

ND

G

ND

A

M

CO

MP

O

NEN

T

VIDE

O

P

R

P

B

Y

M

O

NIT

O

R

OUT

P

R

P

B

Y

AV 2

CO

AXIAL

AV

3

(

CD

)

CO

AXIAL

O

PTI

C

AL

AV

4

A

V

5

AV

6

AV

O

U

T

A

U

DI

O1

S

.VIDE

O

A

UDI

O2

FRO

N

VIDE

O

V

IDE

CO

MP

O

RNENT

V

IDE

O

Digital output

(optical)

TV or projector

16 En

Connections

This unit has input and output jacks for respective input and output sources. You can reproduce sound and movies from

input sources selected with the front panel display or remote control.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ Audio and video player/Set-top box

Connecting other components

Output jacks on the connected external component

Input sources/jacks of this unit

External

components

Signals Output jacks

External component

with HDMI output

Audio/Video HDMI output HDMI1 (BD/DVD) HDMI 1

HDMI2 HDMI 2

HDMI3 HDMI 3

HDMI4 HDMI 4

External component

with component video

output

Audio Optical digital output AV1 (TV) OPTICAL

Video Component video output COMPONENT VIDEO

Audio Coaxial digital output AV2 COAXIAL

Video Component video output COMPONENT VIDEO

External component

with S-video output

Audio Analog audio output AV5 AUDIO

Video S-video output S VIDEO

External component

with composite video

output

Audio Coaxial digital output AV3 (CD) COAXIAL

Video Composite video output VIDEO

Audio Optical digital output AV4 OPTICAL

Video Composite video output VIDEO

Audio Analog audio output AV5 AUDIO

Video Composite video output VIDEO

Audio Analog audio output AV6 AUDIO

Video Composite video output VIDEO

TRIGGER

OUT

PHONO

GND

COMPONENT

VIDEO

P

R

P

B

Y

OPTICAL

(

TV

)

AV 1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

S.VIDEO

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

VIDEO

HDMI 1 HDMI 2 HDMI 3 HDMI 4

(

BD/DVD

)

CENTER

O

UT

TRIGGER OUT

12

V

0.1

A

MAX.

A

NTENNA

UNBAL

.

FM

G

N

D

AM

P

R

P

B

Y

IN

O

U

T

REM

O

T

E

M

ONITOR OU

T

Z

O

NE2

ZONE2

HDMI

V

IDE

O

CO

MP

O

RNENT

V

IDE

O

F

R

O

N

T

CE

OUT

DOCK

Audio/video input

(AV 1-6)

Audio/video output (AV OUT)

Audio input (AUDIO 1-2)

HDMI input

(HDMI 1-4)

Audio output

(AUDIO OUT)

Multi channel audio input (MULTI CH)

Phono input

(PHONO)

Sivu latautuu ...

Yamaha RX-V765 Omistajan opas

Yamaha RX-V765 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat