Parkside PLS 48 B1 Operation and Safety Notes

Tyyppi
Operation and Safety Notes
SOLDERING STATION PLS 48 B1
REGELBARE TSTATION
Bedienungs- und Sicherheitshinweise
L
ÖDSTATION INSTÄLLBAR
Bruksanvisning och säkerhetsanvisningar
REGULERBAR LODDESTATION
Brugs- og sikkerhedsanvisninger
S ÄÄDETTÄ V Ä JUOTINASEMA
Käyttö- ja turvaohjeet
SOLDERING ST ATION
Operation and Safety Notes
66449_par_Loetstation_PLS48B1_cover_FI-SE-DK.indd 6 01.08.11 08:58
GB / IE Operation and Safety Notes Page 5
FI Käyttö- ja turvaohjeet Sivu 21
SE Bruksanvisning och säkerhetsanvisningar Sidan 37
DK Brugs- og sikkerhedsanvisninger Side 53
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 69
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin
toimintoihin.
Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig
bekant med apparatens / maskinens funktioner.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich
anschließend mit allen Funktionen des Gerätes vertraut.
66449_par_Loetstation_PLS48B1_cover_FI-SE-DK.indd 7 01.08.11 08:58
1
6
A
B
7
2
3
4
5
66449_par_Loetstation_PLS48B1_cover_FI-SE-DK.indd 8 01.08.11 08:58
66449_par_Loetstation_PLS48B1_cover_FI-SE-DK.indd 10 01.08.11 08:58
5 GB/IE
Introduction
Proper use ...............................................................................Page 7
Features and equipment ......................................................... Page 8
Included items ......................................................................... Page 8
Technical information ............................................................. Page 8
Safety advice
1. Workplace safety ............................................................... Page 9
2.
Electrical safety .................................................................. Page 9
3. Personal safety ................................................................... Page 10
4. Careful handling and use of electrical power tools ........ Page 12
Original accessories / attachments ....................................... Page 13
Before first use
Inserting / replacing soldering tips ........................................ Page 13
Using the product
Switching on / off and setting the temperature .................... Page 14
Solder sponge......................................................................... Page 15
Soldering ................................................................................. Page 15
Maintenance and cleaning .................................. Page 16
Service centre ................................................................. Page 17
Warranty ............................................................................ Page 17
Disposal ................................................................................ Page 18
Declaration of Conformity /
Manufacturer .................................................................. Page 19
Table of contents
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 5 05.08.11 09:32
6 GB/IE
Introduction
The following pictograms are used in these operating
instructions / on the device:
Read instruction manual!
Observe caution and safety notes!
Caution electric shock! Danger to life!
Risk of explosion!
Risk of fire!
Warning - Hot surfaces!
V
~
Volt (AC)
W
Watts (Effective power)
Wear a breathing / dust mask, protective glasses,
gloves and clothing.
Keep children away from electrical devices!
For indoor use only!
Check that the device, mains lead and plug are in
good condition!
Do not smoke!
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 6 05.08.11 09:32
7 GB/IE
Introduction
Soldering station PLS 48 B1
Q
Introduction
Please make sure you familiarise yourself fully with the way
the device works before you use it for the first time and that
you understand how to handle it correctly. Please read the
operating instructions below. Be careful to keep these advice notes and
if necessary pass them on to a third party.
Q
Proper use
The appliance is intended for electronic soldering for leisure and DIY
purposes. It is suitable for applications such as soldering work, welding
and gluing plastics and the application of decorations. Use the device
only as described and for the indicated purposes. The device is not in-
tended for commercial use. Any other use or modification to the device
shall be considered as improper use and could give rise to considerable
dangers. The manufacturer will not accept liability for loss or damage
arising from improper use.
Do not eat!
Do not drink!
Dispose packaging and appliance in an
environmentally-friendly way!
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 7 05.08.11 09:32
8 GB/IE
Safety advice
Introduction
Q
Features and equipment
1
Soldering pencil
2
ON / OFF switch
3
Accessory compartment
4
Tin solder
5
Solder sponge
6
Temperature regulator
7
Soldering tip
Q
Included items
1 Soldering station with PLS 48 B1 soldering pencil
includes 2 standard soldering tips (1 x mounted)
1 Tin solder, ø 1.0 mm, 20 g
1 Tin solder, ø 1.5 mm, 20 g
1 Solder sponge
1 Operating instructions
Q
Technical information
Electricity supply: 230 V∼
Frequency: 50 Hz
Power consumption: 48 W
Temperature range: 100–500 °C
Mains lead: 1.85 m from the mains plug to the station
1.00 m from the soldering pencil to the station
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 8 05.08.11 09:32
9 GB/IE
Safety advice
Safety advice
CAUTION! Failure to observe the instructions and advice given
below may result in electric shock, fire and/or serious injury.
1. Workplace safety
a) Keep your working area clean and well lit. Untidy or
poorly lit working areas can lead to accidents.
b)
Do not work with the device in potentially
explosive environments in which there are
inflammable liquids, gases or dusts. Electrical
power tools create sparks, which can ignite dusts or fumes.
c)
Keep children and other people away while
you are operating the electrical tool. Distrac-
tions can cause you to lose control of the device.
2. Electrical safety
To avoid danger to life from electric shock:
a)
The mains plug on the device must match
the mains sock-
et. The plug must not be modified in any way. Do not
use an adapter plug with devices fitted with a protec-
tive earth. Unmodified plugs and matching sockets reduce the
risk of electric shock.
b) Keep the device away from rain or moisture. Water en-
tering an electrical device increases the risk of electric shock.
Introduction
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 9 05.08.11 09:32
10 GB/IE
Safety advice
Safety advice
c) Use a residual current device (RCD) for protection if
operating the electrical power tool in a moist environ-
ment is unavoidable. The use of an RCD reduces the risk of
electric shock.
d)
Do not use the mains lead for any purpose for
which it was not intended, e.g. to carry the
device, to hang up the device or to pull the
mains plug out of the mains socket. Keep the mains
lead away from heat, oil, sharp edges or moving parts
of the device. Damaged or tangled mains leads increase the
risk of electric shock.
e) Do not operate the device if the mains lead or mains plug is
damaged.
A damaged mains lead presents a serious
danger to life from electric shock.
f) Always keep the mains lead out of the operating area and run it
away from the rear of the device.
g) Always pull out the mains plug if you are about to leave the device
unattended or wish to carry out any tasks on the device.
3. Personal safety
a) Children or persons who lack the knowledge or expe-
rience to use the device or whose physical, sensory or
intellectual capacities are limited must never be al-
lowed to use the device without supervision or in-
struction by a person responsible for their safety. Chil-
dren must never be allowed to play with the device.
b) Remain alert at all times, watch what you are doing
and always proceed with caution. Do not use the
device if you are tired or under the influence of
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 10 05.08.11 09:32
11 GB/IE
Safety advice
drugs, alcohol or medication. One moment of carelessness
when using the device can lead to serious injury.
DANGER OF BURNS! Never touch the hot soldering
tip or the molten solder. You could suffer burn injuries.
Always let the device cool before you replace components
on the device, clean it or check its condition.
After use let the soldering pencil cool down in air only. Under no
circumstances quench the tip in water!
CAUTION! DANGER OF FIRE! Place the soldering
pencil down only in the special multifunctional holder
or on a fire-resistant pad.
Place the soldering pencil in the multifunctional holder during
pauses in your work.
Keep the device away from combustible material.
Never leave the device switched on and unattended.
CAUTION! DANGER OF INJURY! Keep your hands away
from the hot workpiece. The heat from soldering can be conducted
through the workpiece.
Avoid placing the hot soldering tip in contact with the plastic parts
of the multifunctional holder. Failure to observe this advice may
result in damage to the device.
If a dangerous situation arises, pull the mains plug immediately
out of the mains socket.
CAUTION! DANGER OF POISONING! Do not breathe air
contaminated with soldering fumes.
When working with the device for long periods do not
allow the fumes from soldering to build up. They may
be hazardous to health. Always provide adequate
ventilation of your working area. In addition, it is recommended
that you wear protective gloves, a face mask and a protective
apron.
Safety advice
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 11 05.08.11 09:32
12 GB/IE
Safety advice / Before first use
Safety advice
Do not eat, drink or smoke in rooms where soldering is carried out.
Otherwise your hands may transfer any adhering traces of lead
via food or cigarettes into your body.
Always wash your hands immediately after soldering.
Do not dispose of soldering waste with the household rubbish.
Soldering waste must disposed of as special waste.
4. Careful handling and use
of electrical power tools
a) When not in use always ensure that electrical power
tools are kept out of reach of children. Do not let any-
one use the device if he or she is not familiar with it
or has not read the instructions and advice. Electrical
power tools are dangerous when they are used by inexperienced
people.
b) Look after the device carefully. Check for broken
parts or parts that are damaged to the extent they
detrimentally affect the functioning of the device.
Have any damaged parts repaired before you use
the device. Many accidents have their origins in poorly main-
tained electrical tools.
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 12 05.08.11 09:32
13 GB/IE
Safety advice / Before first use
Q
Original accessories / attachments
Use only the accessories detailed in the operating instructions. The
use of attachments or accessories other than those recommended
here could lead to you suffering an injury.
Q
Before first use
Q
Inserting / replacing soldering tips
CAUTION! DANGER OF BURNS! Allow the soldering
pencil to heat up without a soldering tip.
Remove a soldering tip only when the device has been switched
off and the soldering tip has cooled.
Turn the soldering tip out to replace it.
You must ‘tin’, i.e. thinly coat with solder, the soldering tip
7
before
using the soldering station for the first time and before using a new
soldering tip.
To do this follow these steps:
Insert the mains plug into a mains socket and press the ON / OFF
switch
2
into position “I”.
Turn the temperature regulator
6
to 3 and allow a little solder to
flow and deposit a thin continuous film over the surface of the sol-
dering tip.
Safety advice
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 13 05.08.11 09:32
14 GB/IE
Using the product
Using the product
Q
Using the product
Q
Switching on / off and setting
the temperature
Switching on and setting the temperature:
Insert the mains plug into a mains socket and press the ON / OFF
switch
2
into position “I”.
Turn the temperature control
6
to set the temperature you wish
to have.
Problems will occur during soldering if an unsuitable solder wire used.
The right soldering temperature must be achieved to produce perfect
soldering. If the temperature is too low the solder does not flow enough
and causes contamination of the solder at the joint, a so-called “cold
joint”. At too high a temperature, the flux (flowing aid) burns and the
solder does not flow. The high temperatures may also damage the
workpiece.
The temperature settings suitable for most soldering tasks are given
below. The precise settings may vary, depending on the solder and the
manufacturer.
Level min = room temperature
Setting 1 = approx. 100 °C – warming up stage and for solder with a
low melting point
Setting 2 = 200 °C melting point of most common soft solders
Setting 3 = 300 °C normal operating temperature, e.g. for using
lead-free solder
Setting 4 = 400 °C high soldering temperature, e.g. for desoldering
small soldered joints
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 14 05.08.11 09:32
15 GB/IE
Using the product
Setting 5 = 500 °C maximum soldering temperature, e.g. for desolder-
ing large soldered joints
Switching off:
Note: After use always replace the soldering pencil
1
into the holder.
Press the ON / OFF switch
2
into setting “0”.
If the device is not being used, pull the mains lead out of the mains
socket.
Q
Solder sponge
CAUTION! The hot soldering tip
7
must never be placed in
contact with a dry solder sponge
5
, otherwise the solder sponge
may be damaged.
The solder sponge
5
is used to clean soldering tips.
Moisten the solder sponge
5
before you use it.
Q
Soldering
The soldering pencil has a rated output of 48 watts and is therefore
ideal for electronics soldering (see Figs. A, B).
The design of the soldering pencil makes it especially suitable for
use where access is difficult or for fine soldering work.
Clean the soldering tip
7
on the moist solder sponge
5
.
After cleaning the tip
7
it must be “tinned” (coated with solder).
This is done by melting solder on to the hot soldering tip
7
.
Guide the soldering tip
7
to the intended joint site and heat the joint.
Place the solder (with flux) between the joint site and the tip
7
to melt it.
Using the product
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 15 05.08.11 09:32
16 GB/IE
Service centre / Warranty
Using the product / Maintenance and cleaning
Continue to feed further solder until the whole joint has a covering
of solder.
Then quickly remove the soldering tip in order to avoid overheating
the molten solder.
Allow the solder to harden while not subjecting it to vibration or
movement.
Note: The flux is either already contained in the solder or applied
separately.
Ask the advice of the retailer when buying solder in order to choose
the most suitable solder for your intended purpose.
Attachments and applications:
ATTENTION! Do not carry out any special changes or repairs to the
electrics or other parts. Exceptions are permitted if the person carrying
out such changes or repairs is qualified or trained to do so.
Try every application out on surplus material and see if you get the effect
you wish to have. This means you will avoid damaging the item you
wish to work on.
Q
Maintenance and cleaning
RISK OF INJURY! Before you carry out any work
on the device always pull the mains plug out of the mains socket and
allow the device to cool.
Clean the device after you have finished using it.
Use a cloth and a little mild detergent for cleaning the device.
In no circumstances use sharp objects, or petrol, solvents or clean-
ing agents that might attack plastic.
Do not allow any liquids to enter the inside of the device.
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 16 05.08.11 09:32
17 GB/IE
Service centre / Warranty
Q
Service centre
Have your device repaired only by
qualified specialist personnel using original manufactur
er
parts only. This will ensure that your device remains safe to use.
If the plug or mains lead needs to be
replaced, always have the replacement carried out
by the manufacturer or his service centre. This will ensure
that your device remains safe to use.
Q
Warranty
The warranty for this appliance is for 3 years from the
date of purchase. The appliance has been manufactured
with care and meticulously examined before delivery.
Please retain your receipt as proof of purchase. In the
event of a warranty claim, please make contact by tele-
phone with our Service Department. Only in this way
can a post-free despatch for your goods be assured.
The warranty covers only claims for material and maufacturing defects,
but not for transport damage, for wearing parts or for damage to frag-
ile components, e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
The warranty is void in the case of abusive and improper handling, use of
force and internal tampering not carried out by our authorized service
branch. Your statutory rights are not restricted in any way by this warranty.
The warranty period will not be extended by repairs made unter warra
nty.
This applies also to replaced and repaired parts. Any damage and de-
Using the product / Maintenance and cleaning
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 17 05.08.11 09:32
18 GB/IE
Disposal / Declaration of Conformity / Manufacturer
Warranty / Disposal
fects extant on purchase must be reported immediately after unpacking
the appliance, at the latest, two days after the purchase date. Repairs
made
after the expiration of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
IAN 66449
IE
Service Ireland
Tel: 1890 930 034
(0,08 EUR/Min. (peak)
0,06 EUR/Min. (off peak))
IAN 66449
Q
Disposal
The packaging is wholly composed of environmentally-
friendly materials that can be disposed of at a local
recycling centre.
Do not dispose of electrical devices
with the household rubbish!
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 18 05.08.11 09:32
19 GB/IE
Disposal / Declaration of Conformity / Manufacturer
In accordance with European Directive 2002 / 96 / EC (covering
waste electrical and electronic equipment) and its transposition into
national legislation, worn out electrical devices must be collected
separately and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for more details of how to
dispose of your worn-out devices.
Q
Declaration of Conformity / Manufacturer
We, Kompernaß GmbH, the person responsible for documents: Mr Semi
Uguzlu, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that
this product complies with the following standards, normative documents
and EU directives:
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60335-2-45/A1:2008
EN 60335-1/A14:2010
EN 62233:2008
EN 55014-1/A1:2009
EN 55014-2/A2:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2008
Warranty / Disposal
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 19 05.08.11 09:32
20 GB/IE
Declaration of Conformity / Manufacturer
Type / Machine designation:
Soldering station PLS 48 B1
Date of manufacture (DOM): 08–2011
Serial number: IAN 66449
Bochum, 31.08.2011
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications in the course of
product development.
Sisällysluettelo
66449_par_Loetstation_PLS48B1_content_FI-SE-DK.indd 20 05.08.11 09:32
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86

Parkside PLS 48 B1 Operation and Safety Notes

Tyyppi
Operation and Safety Notes

muilla kielillä