Dometic M55LX AHD, M75LX AHD Käyttö ohjeet

M55LX AHD, M75LX AHD

LCD Monitor

Installation and Operating Manual . . . . . . 9

LCD-Monitor

Montage- und Bedienungsanleitung . . . 23

Ecran LCD

Instructions de montage et de service . . 38

Pantalla LCD

Instrucciones de montaje y de uso . . . . .53

Monitor LCD

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 68

Monitor LCD

Istruzioni di montaggio e d’uso . . . . . . . . 83

LCD-monitor

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 98

LCD-monitor

Monterings- og betjeningsvejledning. . 113

LCD-monitor

Monterings- och bruksanvisning . . . . . . 127

LCD-monitor

Monterings- og bruksanvisning . . . . . . . 142

LCD-monitori

Asennus- ja käyttöohje. . . . . . . . . . . . . . 157

ЖК-монитор

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 172

Monitor LCD

Instrukcja montażu i obsługi . . . . . . . . . 187

LCD monitor

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . 202

Monitor LCD

Návod k montáži a obsluze . . . . . . . . . . 217

LCD-monitor

Szerelési és használati útmutató . . . . . . 232

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

POWER & CONTROL

MONITORS

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 1 Donnerstag, 27. Juni 2019 8:30 20

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 2 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

3

1

4

8

12 13 14

911

56 7

23

10

1

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 3 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

4

2

3

4

5

6

7

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 4 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

5

8

1

3

2

9

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 5 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

6

1

2

3

4

5

6

7

8

0

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 6 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

7

1.

2.

3.

a

1

b

1 2

c

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 7 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD

8

132

9

6

5

8

4

12

7

13

10

11

d

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 8 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Explanation of symbols

EN

9

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Installing the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8 Using the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

9 Cleaning and caring for the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1 Explanation of symbols

!

A

I

CAUTION!

Safety instruction: Indicates a hazardous situation that, if not avoided, could result in

minor or moderate injury.

NOTICE!

Indicates a situation that, if not avoided, can result in property damage.

NOTE

Supplementary information for operating the product.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 9 Donnerstag, 27. Juni 2019 8:30 20

Safety and installation instructions M55LX AHD, M75LX AHD

EN

10

2 Safety and installation instructions

Please observe the safety instructions and stipulations issued by the vehicle

manufacturer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

•

Faulty assembly or connection

•

Damage to the product resulting from mechanical influences and incorrect connection voltage

•

Alterations to the product without express permission from the manufacturer

•

Use for purposes other than those described in the operating manual

A

Therefore, please observe the following instructions:

•

When working on the following cables, only use insulated cable terminals, plugs and flat

sockets:

– 30 (direct supply from positive battery terminal)

–15 (connected positive terminal, behind the battery)

– 31 (return cable from the battery, earth)

– 58 (reversing light)

Do not use porcelain wire connectors.

•

Use a crimping tool (fig. 1 12, page 3) to connect the cables.

•

Screw the cable when connecting cable 31 (earth)

– Screw on the cable using a cable terminal and serrated washer to one of the vehicle's earth

bolts or

– Screw the cable to the bodywork using a cable terminal and a self-tapping screw

Make sure there is a good earth connection.

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

NOTICE! Beware of damage

•

To prevent the risk of short circuits, always disconnect the negative terminal of the

vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be

disconnected.

•

Inadequate supply cable connections could result in short circuits, causing:

–Cable fires

– The airbag being triggered

– Damage to electronic control equipment

– Electrical malfunctions (indicators, brake light, horn, ignition, lights)

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 10 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Safety and installation instructions

EN

11

•

The following data must be reset, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the operating manual.

Observe the following installation instructions:

!

Observe the following instructions when working with electrical parts:

•

When testing the voltage in electrical cables, only use a diode test lamp (fig. 1 1, page 3) or

a voltmeter (fig. 1 2, page 3).

Test lamps with a bulb (fig. 1 3, page 3) consume voltages which are too high and can

damage the vehicle's electronic system.

•

When routing the electrical connections, ensure that:

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp-edged ducts without protection (fig. 3, page 4).

•

Insulate all connections.

•

Secure the cables against mechanical wear by using cable binders or insulating tape,

for example on existing cables.

Observe the following instructions when handling the LCD monitor:

!

CAUTION!

•

Secure the monitor in such a way that it cannot become loose under any

circumstances (sudden braking, accidents) and cause injuries to the occupants

of the vehicle.

•

Do not attach the monitor in the air bag deployment path, as this could cause injury

if the airbags are triggered.

CAUTION!

•

People (including children) whose physical, sensory or mental capacities or whose

lack of experience or knowledge prevent them from using this product safely

should not use it without the supervision or instruction of a responsible person.

•

Do not open the monitor (fig. 4, page 4).

•

Do not submerge the monitor in water (fig. 5, page 4); the monitor is not

waterproof.

•

The monitor must not impair your vision when driving (fig. 8, page 5).

•

Do not operate the monitor with wet hands.

•

Do not operate the monitor if the housing has been damaged.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 11 Donnerstag, 27. Juni 2019 8:30 20

Scope of delivery M55LX AHD, M75LX AHD

EN

12

A

3Scope of delivery

4 Accessories

Available as accessories (not included in the scope of delivery):

NOTICE!

•

Connect it to the correct voltage.

•

Do not use the monitor in areas which

– are subjected to direct sunlight,

– are subject to strong temperature fluctuations,

– have high levels of humidity,

–are poorly ventilated,

– are dusty or oily.

•

Do not press against the LCD display.

•

Do not drop the monitor.

•

If you use the monitor in vehicles, the vehicle should be running during operation

to prevent the vehicle battery from discharging.

•

The picture quality can be impaired in the vicinity of electromagnetic fields.

For this reason do not mount the monitor near loudspeakers.

No. in

fig. 9,

page 5

Quantity Description

Ref. no.

M55LX AHD M75LX AHD

1 1 Monitor 9600012883 9600012899

2 1 Monitor bracket 9102200193

3 1 Monitor bracket cover

– 1 Connection cable 9102200196

––Fastening material

Description Ref. no.

Sun visor for M55LX AHD 9102200200

Sun visor for M75LX AHD 9102200201

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 12 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Intended use

EN

13

5Intended use

The LCD monitors PerfectView M55LX AHD and M75LX AHD are monitors which are primarily in-

tended for use in vehicles. They can be used together with cameras (e.g. a reversing video system)

or other video sources.

The LCD monitors are designed for use in all vehicles.

The LCD monitors are designed for commercial use.

6 Technical description

6.1 Function description

The LCD monitor can be connected to cameras (e.g. reversing video systems) or other video

sources (e.g. DVD players). It is possible to switch back and forth between video sources.

The monitor features control cables which allow the cameras to be activated automatically.

It can operate up to four cameras. Alongside the usual controls, the four cameras can be switched

consecutively in automatic mode. This monitor also features a distance indicator in the display

which is activated automatically when the reverse gear is engaged (CAM1).

6.2 Control elements

The following control elements are located on the monitor:

No. in

fig. 0,

page 6

Descrip-

tion

Description

1 Sensor window for the dimmer function.

The brightness of the display is automatically adapted to the

ambient light.

2 P Switches the monitor on and off.

The button lights up red when the monitor is in standby. It lights up

green when the monitor is switched on.

3 + 1. Increases the brightness.

2. Increases the value of the selected parameter if a menu is

opened.

4 – 1. Reduces the brightness.

2. Reduces the value of the selected parameter if a menu is

opened.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 13 Donnerstag, 27. Juni 2019 8:30 20

Technical description M55LX AHD, M75LX AHD

EN

14

51.Switches the menu on.

2. Calls up the parameters for setting.

The parameters are distributed over four screen pages in the

following order:

Page 1: Picture

–Brightness

–Contrast

–Colour

–Volume

–Auto Dim

– Distance: Distance marker setting

Page 2: Options

– Language: German, English, French, Italian, Dutch, Spanish,

Portuguese, Russian

– Scale: switches the distance markers on or off

– Camera 1/Camera 2/Camera 3/Camera 4: Normal or

Mirrored

– Sensitivity: Setting of the switching threshold for the night

dimmer function

– Trailer detection ON/OFF: Shortens the activation time in

OFF mode

Page 3: Auto search

– Automatic search Switches the automatic camera panning on

(the cameras are activated in preset time intervals, e.g. for

horse transporters with multi-box monitoring).

– Camera 1/Camera 2/Camera 3/Camera 4: Setting for the

switching intervals

– Reset (“Default”): Default setting for all parameters

6 CAM Switches from one camera to the next.

7Monitor bracket

8 Loudspeaker

No. in

fig. 0,

page 6

Descrip-

tion

Description

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 14 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Installing the LCD monitor

EN

15

7 Installing the LCD monitor

7.1 Tools required (fig. 1, page 3)

For installation and assembly you will need the following tools:

•

Measuring ruler (4)

•

Centre punch (5)

•

Hammer (6)

•

Drill head set (7)

•

Drill (8)

•

Screwdriver (9)

To establish and test the electrical connection, the following tools are required:

•

Diode test lamp (1) or voltmeter (2)

•

Insulating tape (10)

•

Heat shrinking sleeve

•

Hot air blower (11)

•

Crimping tool (12)

•

Soldering iron (optional) (13)

•

Solder (optional) (14)

•

Cable bushing sleeves (optional)

To fasten the cables, you may require additional cable binders.

7.2 Installing the monitor

!

Observe the following installation instructions:

•

Select an installation location that provides an unobstructed view of the monitor (fig. 6 and

fig. 7, page 4).

•

Never install the monitor in areas where your head could hit it or in the airbag deployment path.

This could cause injury if the airbag opens.

•

The monitor must not impair your vision when driving (fig. 8, page 5).

•

The installation location should be flat.

•

Check that there is sufficient space underneath the installation location to attach the washers

and nuts.

CAUTION! Beware of injury

Select the location of the monitor so that it cannot injure the passengers in the vehicle

under any circumstances (e.g. sudden braking, road traffic accidents).

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 15 Donnerstag, 27. Juni 2019 8:30 20

Installing the LCD monitor M55LX AHD, M75LX AHD

EN

16

•

Check beforehand that there is sufficient space on the other side for the drill head to come out

(fig. 2, page 4).

•

Bear in mind the weight of the monitor. Provide reinforcement if necessary (larger washers or

plates).

•

Make sure you can lay the connection cable to the monitor.

Choosing the installation location (fig. a, page 7)

➤ Place the monitor on the monitor bracket.

➤ Position the monitor and the attached monitor bracket provisionally.

➤ Mark the outlines of the corners of the support base on the dashboard.

➤ Take the monitor off the monitor bracket.

Screwing the monitor bracket onto the dashboard (fig. b, page 7)

➤ Hold the support base within the outlines marked beforehand.

➤ Fasten the monitor bracket with the self-tapping screws.

Fastening the monitor

➤ Set the monitor on the monitor bracket and secure it with the knurled nut (fig. a, page 7).

➤ Slide the cover over the monitor bracket on the monitor.

7.3 Connecting the monitor electrically

The circuit diagram for the LCD monitor can be found in fig. d, page 8:

No. Description

1Monitor

220-pin socket

3 Monitor line

4 20-pin plug

5 12 – 24 V positive cable (red): connected to the positive pole of the ignition

(connected positive, terminal 5) or the positive pole of the battery

(terminal 30).

6 Earth cable (black): connected to the negative pole of the voltage source.

7 Cable (green): control input for video input CAM1,

such as for connecting the reversing light

8 Cable (white): control input for video input CAM2,

such as for the side camera

9 6-pin CAM1 socket (connection to video source 1)

10 6-pin CAM2 socket (connection to video source 2)

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 16 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Installing the LCD monitor

EN

17

A

Observe the following instructions when laying the connection cable:

•

If possible, use original ducts for laying the cables, or other suitable options, such as ventilation

grilles. If there are no existing ducts, you must drill a hole of ∅ 22 mm. Check beforehand that

there is sufficient space on the other side for the drill head to emerge (fig. 2, page 4).

•

Cover the holes with the feed through (fig. b 1, page 7) in the base of the monitor bracket.

•

To prevent damage to the cables, when laying them ensure that there is always sufficient

distance to vehicle components which can become hot (lights, heaters, ventilators etc.).

•

When laying the cables (fig. 3, page 4), make sure:

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp-edged ducts without protection.

Connecting the monitor as a reversing video system (fig. d, page 8)

➤ Lay the connection cable for the monitor bracket on the dashboard.

➤ Insert the plug of the monitor cable (2) into the socket (4) of the connection cable (3).

Wait until you hear the plug snap in.

A

➤ Connect the red and black cables of the connection cable to a suitable voltage supply:

– Connect the red cable (5) to terminal 15 (ignition).

– Connect the black cable (6) to terminal 31 (earth).

➤ If the monitor is to be activated when reverse gear is selected, connect the green cable (7) to

the positive cable of the reversing light.

11 6-pin CAM3 socket (connection to video source 3)

with video signal detection

12 6-pin CAM4 socket (connection to video source 4),

with video signal detection)

13 Cable (blue): control input for video input CAM3

If the system is activated via this control line, none of the buttons have a

function (according to DIN EN 1501-1).

NOTICE!

Cables and connections that are not properly installed will cause malfunctions or

damage to components.

Correct installation of cables and connections ensures lasting and trouble-free

operation of the retrofitted components.

NOTICE! Beware of damage

Make sure the polarity is correct when connecting to a voltage source.

No. Description

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 17 Donnerstag, 27. Juni 2019 8:30 20

Using the LCD monitor M55LX AHD, M75LX AHD

EN

18

I

➤ If the monitor is to be activated e.g. when the indicator is flashing, connect the following

control cable to a positive cable of the indicator:

–white cable (8), blue cable (13)

I

This control cable is used as a signal cable for the activation of a side camera when an indicator is

flashing, for example.

➤ If necessary, connect the CAM1 socket (9) of the connection cable to the plug of video source

1 (e.g. reversing camera).

➤ If necessary, connect the CAM2 socket (10) of the connection cable to the plug of the video

source 2 (e.g. side camera).

➤ If necessary, connect the CAM3 socket (11) of the connection cable to the plug of video source

3 (e.g. camera).

I

Connecting an additional reversing camera (trailer operation)

➤ If necessary, connect socket CAM4 (12) of the connection cable to the plug of the additional

reversing camera.

8 Using the LCD monitor

8.1 Switching on the monitor

➤ If the monitor is switched off, press the P button (fig. 0 2, page 6) to switch the monitor on.

➤ The button lights up green.

✓ The picture appears.

8.2 Switching off the monitor

➤ Press the P button (fig. 0 2, page 6) to switch off the monitor.

➤ The button lights up red.

✓ The picture disappears.

NOTE

If voltage is present in the green cable (7), the reversing camera will be activated

automatically. The reversing camera has priority.

NOTE

If voltage is present in this control cable, the video input CAM2 and CAM3 will be

activated.

NOTE

Observe the power consumption of the video system. The cameras are equipped with

heaters. A maximum current of 1.5 A can flow (three cameras in heating mode). Use a

disconnector switch for direct connection to the battery. This allows you to disconnect

the video system from the battery easily if you are no longer using the vehicle.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 18 Donnerstag, 27. Juni 2019 8:30 20

M55LX AHD, M75LX AHD Using the LCD monitor

EN

19

8.3 Setting the monitor

To set the monitor to suit your requirements, proceed as follows (fig. 0, page 6):

➤ Press the button (5) to call up the required parameter.

✓ The parameters to be set appear in the following order:

Page 1: Picture

– Brightness: 0 – 100

–Contrast: 0 – 100

– Colour: 0 – 100

–Volume: 0 – 100

– Auto Dim On, Off

– Distance: distance marker setting (chapter “Setting the distance markers” on page 20)

Page 2: Options

– Language: German, English, French, Italian, Dutch, Spanish, Portuguese, Russian

– Scale: On, Off

(switches the distance markers on or off)

– Camera 1/Camera 2/Camera 3/Camera 4: Normal or Mirrored

– Sensitivity: 1, 2

Setting of the switching threshold for the night dimmer function to avoid glare.

In dimming mode, the switching threshold can be set at two levels.

– Trailer detection ON/OFF: Shortens the activation time in OFF mode

Page 3: Auto search

– Automatic search: On, Off

Switches the automatic camera panning on (the cameras are activated in preset time

intervals, e.g. for horse transporters with multi-box monitoring).

– Camera Delay: Setting of the delay intervals (2 to 20 s)

– Default: Default setting for all parameters

➤ Press the “+” button (3) or the “–” button (4) to set the required parameter.

➤ Press the “+” button (3) to increase the value of the selected parameter.

➤ Press the “–” button (4) to reduce the value of the selected parameter.

8.4 Setting the video source

Proceed as follows to set the video source (fig. 0, page 6):

➤ If you want to switch to a different video source, press the “CAM” button (6).

✓ The monitor changes the camera in the order “Camera 1 – Camera 2 – Camera 3 – Camera 4”.

I

NOTE

If you want the cameras to run automatically: see chapter “Setting the automatic

search” on page 20.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 19 Donnerstag, 27. Juni 2019 8:30 20

Using the LCD monitor M55LX AHD, M75LX AHD

EN

20

8.5 Setting the automatic search

Proceed as follows to set the automatic search (fig. 0, page 6):

➤ Press the “ ” button (5) until the “Auto search” menu appears.

➤ Press the “+” button (3) to switch on the automatic search.

✓ The monitor starts the cameras in the order “Camera 1 – Camera 2 – Camera 3 – Camera 4”

automatically in the preset time.

After the first run through, only the inputs with connected cameras are shown.

No sound is available in this operating mode.

Setting the display time

You can set the display time from 2 to 20 seconds.

➤ Press the “ ” button (5) until the “Cam Delay” menu appears.

➤ Press the “+” button (3) to increase the camera display time.

Press the “–” button (4) to reduce the camera display time.

Quitting the automatic search

➤ Press the “ ” button (5) until the “Auto search” menu appears.

➤ Press the “+” button (3) to switch off the automatic search.

8.6 Detecting the trailer camera

This function is required when using a trailer camera (fig. c, page 7) if the system is activated

automatically via the reverse gear. To initialise the automatic detection switch off ignition once.

•

One camera connected (e.g. towing vehicle without a trailer):

the camera connected to CAM1 (1) is activated.

•

Two cameras connected (e.g. towing vehicle with a trailer):

the camera connected to CAM4 (2) is activated (CAM1 is inactive).

8.7 Setting the distance markers

To set the distance markers, proceed as follows (fig. 0, page 6):

➤ Press the “ ” button (5) until the “Scale” menu appears.

✓ The distance markers to be set appear.

➤ Press the “+” button (3) to move the red highlighted distance markers.

➤ Press the “–” button (4) to select the next distance marker.

➤ Press the “ ” button (5) to exit the settings.

M55LX-AHD-M75LX-AHD-IO-16s.book Seite 20 Donnerstag, 27. Juni 2019 8:30 20

Sivu latautuu...

Dometic M55LX AHD, M75LX AHD Käyttö ohjeet

Dometic M55LX AHD, M75LX AHD Käyttö ohjeet

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat