Murray 629904X54A Instruction book

InstructionBook

SnowThrower

Model629904x54A

Q ManueldeI'utilisateur Chasse-neige

module629904x54A

Betriebsanleitung

Schneefriise

Modell629904x54A

Q IstruzioniperI'uso Spazzaneve

Modello629904x54A

Bruksanvisning

Snefreser

modell629904x54A

Anv_ndarhandbok Sn6slunga

modell629904x54A

Ohjekirja

ManualdeInstrucciones

Lumilinko

malli629904x54A

Quitanieves

modelo629904x54A

F-O21033L

4 3

; 15 19

18

/!

\

3_

/:

/

11

\

4

1 5_

16

\ /

4

_6

F-O21033L 2

z _8

2

7 12 6

/

7

\

6

9_

\

lO

1

2

12

F-O21033L 3

/

2

/3

4

/4

4

L5

16

F-O21033L 4

1! 5 6 5 18

1

\

3

2

3

6

6_

2O

21

17

9

4

22

13

F-O21033L 5

4

23

\

6 3

2

24

8

25

26

. p

! mL, 1 f.,l_ m

t I

2!

28

F-O21033L 6

29 30

10

6

5

4

5

3

\

ilillll_

3/

11 3

_,ii¸¸¸¸_

19

20

8

13

17

F-021033L 7

2

©

1 1

rI

2

F-O21033L 8

CONTENTS

PRODUCT INFORMATION 9

OWNER'S INFORMATION 9

INTERNATIONAL PICTORIALS 10

ASSEMBLY 12

OPERATION 12

MAINTENANCE 15

MAINTENANCE CHART 15

TROUBLE SHOOTING CHART 18

TWO YEAR LIMITED WARRANTY

Murray, Inc. warrants to the original purchaser

that this unit shall be free from defects in

material and workmanship under normal use

and service for a period of Two (2) Year from

the date of purchase; however, this warranty

does not cover engines, accessories (such as

electric starters) and Normal Wear Parts (except

as noted below) as the companies that

manufacture these items furnish their own

warranties and provide service through their

authorized field service facilities. For additional

information, see the warranties covering these

particular parts. If you are uncertain whether

your unit contains or is equipped with one or

more of these parts, consult your dealer prior to

purchase. Subject to the terms and conditions

noted in this Limited Warranty, we shall, at our

option, repair or replace at no cost to the original

purchaser any part covered by this Limited

Warranty during the applicable warranty period.

Normal Wear Parts ere defined as drive belts,

augers, shear pins, tires and headlights. These

parts are warranted to be free from defects in

material end workmanship as delivered with the

product. Any claim for repair or replacement of

Normal Wear Parts must be made within thirty

(30) days of the date of purchase. No claims

involving damage caused from material use,

abuse or misuse will be honored.

This Murray, Inc. Two (2) Year Limited

Warranty is your exclusive remedy; however,

this warranty is void or does not apply to any

unit that has been tampered with, altered,

misused, abused or used for rental or other

commercial and/or professional

(non-homeowner) uses. Your warranty does not

cover minor mechanical adjustments which are

not due to any defect in material or

workmanship. For assistance in making such

adjustments, consult your Instruction Book.

To make a claim under this Murray, Inc. Two (2)

Year Limited Warranty, return the unit (or if

authorized in advance, the defective part) along

with your proof of purchase to an Authorized

Service Center near you. To locate the nearest

Authorized Service Center, call the Central Parts

Distributor for your area shown in the list

provided with your unit or check the Yellow Page

listings in your local telephone directory. If you

return the entire unit, we will repair the unit. If we

authorize the return of the defective part only, we

will either replace or repair the part. This Murray,

Inc. Two (2) Year Limited Warranty gives you

specific legal rights, and you may also have

other rights which vary from state to state. This

Limited Warranty is given in lieu of all other

expressed and implied warranties including

the implied warranty of merchantability and

warranty of fitness for a particular purpose. If

you need additional information on this written

warranty or assistance in obtaining service,

write:

RAYTER LIMITED,

Service Department,

Spellbroek,

Bishop's Stortford,

Hertfordshire. CM23 4BU.

MURRAY, INC.

Outdoor Power Equipment

Customer Service Department

P.O. Box 268

Brentwood, Tennessee U.S.A. 37027

1-800-251-8007

PRODUCT INFORMATION

The owner must be certain that all the product

information is included with the unit. This

information includes the INSTRUCTION

BOOKS, the REPLACEMENT PARTS and the

WARRANTIES. This information must be

included to make sure state laws end other laws

are followed.

OWNER'S INFORMATION

This instruction book is written for a person with

some mechanical ability. Like most service

books, not all the steps are described. Steps on

how to loosen or tighten fasteners ere steps

anyone can follow with some mechanical ability.

Read and follow these instructions before you

use the unit.

Know your product: If you understand the unit

and how the unit operates, you will get the best

performance. As you read this manual, compare

the illustrations to the unit. Learn the location

and the function of the controls. To help prevent

an accident, follow the operating instructions

and the safety rules. Keep this manual for future

reference.

IMPORTANT: Many units are not assembled 3.

and are sold in cartons. It is the responsibility of 4.

the owner to make sure the assembly instruc-

tions in this manual are exactly followed. Other

units are purchased in an assembled condition.

On assembled units, it is the responsibility of the 5.

owner to make sure the unit is correctly as-

sembled. The owner must carefully check the

unit according to the instructions in this manual 6.

before it is first used.

7.

8.

mURRAY

t=

WARNING: Look for this symbol to indicate

important safety precautions. This symbol

indicates: "Attention! Become Alert! Your

Safety Is At Risk."

Responsibility Of The Owner

The responsibility of the owner is to

follow the instructions below.

t,

2,

MODEL NO.: 629904x54A

SKU No.:

YYYY MM DD:

SERIAL NO.:

3700 min-1

129 kg

Manufactured in Lawrenceburg, TN 38464, U.S.A.

Carefully read and follow the rules for safe

operation.

Fellow ell the assembly and preparation

instructions.

Inspect the unit.

Make sure that the operator of the unit

knows how to correctly use all standard

and accessory equipment.

Operate the unit only with guards, shields,

and other safety items in place and working

correctly.

Correctly adjust the unit.

Service the unit only with authorized or ap-

proved replacement parts.

Complete all maintenance on the unit.

Environmental Awareness

• Do not fill the engine's fuel tank completely

full.

• Drain fuel for off-season storage.

• Use only unleaded gasoline.

• Service the air cleaner regularly.

• Change oil regularly. Use 5W-30 oil.

• Tuoe-up the engine regularly.

• Keep equipment in efficient operating

condition.

• Dispose of used engine oil properly.

Declared vibration emission values in accordance with Directive 98/37/E0.

Vibration Emission according to EN 1033;1996:10.6 m/s2.

Values determined at the handle when the machine was operated stationary on a

concrete surface at 3700 mint.

F-021033L

Declared airborne noise emissions of LWA108 dB is in accordance with Directive

2000/14/EC, Annex V.

Sound Pressure Level at operator position 86 dB.

Values determined at ear according to the specifications of EN ISO 11201.

9

INTERNATIONAL PICTORIALS

IMPORTANT: The following pictorials are Io*

cated on your unit or on literature supplied

with the product. Before you operate the

unit, learn and understand the purpose for

each pictorial.

Safety Warning Symbols

DANGER

Thrown Objects.

Keep Bystanders Away.

O

DANGER

Thrown Objects.

Keep Bystanders Away.

IMPORTANT

Read Owner's Manual

Before Operating

WARNING This Machine.

DANGER

Stop The Engine

WARNING Before Unclogging

Hot Surface STOP Discharge Chute!

DANGER

Avoid Injury From

Rotating Auger. Keep

Hands, Feet And

Clothing Away.

36

C0ntr0, And 0perat_0ls ) _ _)

Slow Fast Electric Start Engine Start Engine Run Engine Off

Engine Stop On Choke Off Choke On Neutral Forward

T

Reverse Throttle Primer Button Ignition Key

® Q

Ignition Off Ignition On

Push To Engage

Electric Starter

Engage Auger Clutch Auger Collector Discharge DOWN Discharge UP

Discharge LEFT Discharge RIGHT Drive Clutch Fuel Oil Fuel Oil Mixture

Weight Transfer

Lift Handle To Engage

Weight Transfer

Depress Pedal To Disengage

O

Transmission

Ignition Key

Insert To Run, Pull Out To Stop.

F-O21033L 10

Safe Operation Practices for Snow Throwers

IMPORTANT: Safety standards require operator

presence controls to minimize the risk of injury.

Your snow thrower is equipped with such con-

trols. Do not attempt to defeat the function of the

operator presence control under any circum-

stances.

Training

1. Read the operating and service instruction

manual carefully. Be thoroughly familiar with

the controls and the prober use of the equip-

ment. Know how to stop the unit and disen-

gage the controls quickly.

2. Never allow children to operate the equip-

ment. Never allow adults to operate the

equipment without proper instruction,

3. Keep the area of operation clear of all per-

sons, particularly small children and bets.

4. Exercise caution to avoid slipping or falling

especially when operating in reverse.

Preparation

1. Thoroughly inspect the area where the equip-

ment is to be used and remove all doormats,

sleds, boards, wires, and other foreign ob-

jects.

2. Disengage all clutches before starting the en-

gine (motor).

3. Do not operate the equipment without wear-

ing adequate winter outer garments. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container.

b. Never remove fuel tank cap or add fuel to

a running engine (motor) or hot engine

(motor).

c. Fill fuel tank outdoors with extreme care.

Never fill fuel tank indoors.

d. Replace fuel cap securely and wipe up

spilled fuel.

e. Never store fuel or snow thrower withfuel

in the tank inside of a building where

fumes may reach an open flame or spark.

Check fuel supply before each use, allow-

ing space for expansion as the heat of the

engine (motor) and/or sun can cause fuel

to expand.

5. For all units with electric starting motors use

alectdc starting extension cords certified

CSA/UL. Use only with a receptacle that has

been installed in accordance with local in-

spection authorities.

6. Adjust the snow thrower height to clear gravel

or crushed reck surface.

7_

a_

9.

Never attempt to make any adjustments

while the engine (motor) is running (except

when specifically recommended by manufac-

turer).

Let engine (motor) and snow thrower adjust

to outdoor temperatures before starting to

alear scow.

Always wear safety glasses or eye shields

during operation or while performing an ad-

justment or repair to protect eyes from foreign

objects that may be thrown from the snow

thrower.

Operation

1. Do not operate this machine if you are taking

drugs or other medication which can cause

drowsiness or affect your ability to operate

this machine.

2. Do not use this machine if you are mentally

or physically unable to operate this machine

safely.

3. Do not put hands or feet near or under rotat-

ing parts. Keep clear of the discharge open-

ing at all times.

4. Exercise extreme caution when operating on

or crossing gravel drives, walks or roads.

Stay alert for hidden hazards or traffic.

5_

After stdking a foreign object, stop the engine

(motor), remove the wire from the spark plug,

thoroughly inspect snow thrower for any

damage, and repair the damage before re-

starting and operating the snow thrower.

6_

If the unit should start to vibrate abnormally,

stop the engine (motor) and check immedi-

ately for the cause. Vibration is generally a

warning of trouble.

7_

Stop the engine (motor) whenever you leave

the operating position, before unclogging the

auger/imbeller housing or discharge chute

and when making any repairs, adjustments,

or inspections.

a_

When cleaning, repairing, or inspecting, make

certain the auger/imbeller and all moving

parts have stopped and all controls are dis-

engaged. Disconnect the spark plug wire and

keep the wire away from the spark plug to

prevent accidental starting.

9_

Take all possible precautions when leaving

the snow thrower unattended. Disengage the

auger/impeller, stop engine (motor), and re-

move key.

10. Do not run the engine (motor) indoors, except

when starting the engine (motor) and for

transporting the snow thrower in or out of the

building. Open the outside deers; exhaust

fumes are dangerous (containing CARBON

MONOXIDE, an ODORLESS and DEADLY

GAS).

11. Do not clear snow across the face of slopes.

Exeralse extreme caution when changing

direction on slopes. Do not attempt to clear

steep slopes.

12. Never operate the snow thrower without

proper guards, plates or other safety protec-

tive devices in place.

13. Never operate the snow thrower near enclos-

ures, automobiles, window wells, drop_3ffs,

and the like without proper adjustment of the

snow discharge angle. Keep children and

pets away.

14. Do not overload the machine capacity by at-

tempting to clear snow at too fast a rate.

15. Never operate the machine at high transport

speeds on slippery surfaces. Look behind

and use care when backing up.

16. Never direct discharge at bystanders or allow

anyone in front of the unit.

17. Disengage power to the collectar/imbeUer

when snow thrower is transported or not in

use.

18.

19.

20.

21.

22.

23.

Use only attachments and accessories ap-

proved by the manufacturer of the snow

thrower (such as tire chains, electric start kits,

ect.).

Never operate the snow thrower without good

visibility or light. Always be sure of your foot-

ing and keep a firm hold on the handles.

Walk;never run.

Do not over-reach. Keep proper footing and

balance at all times.

Exercise caution if operating on steep slop-

ing surfaces.

This snow thrower is for use on sidewalks,

driveways and other ground level surfaces.

Do not use the snow thrower on surfaces

above ground level such as roofs of resi-

dences, garages, porches or other such

structures or buildings.

Maintenance And Storage

1. Check shear bolts and other bolts at frequent

intervals for prober tightness to be sure the

equipment is in safe working condition.

2. Never store the snow thrower with fuel in the

tank inside a building where ignition sources

are present such as hot water and space

heaters, clothes dryers, and the like. Allow

the engine (motor) to cool before storing in

any enclosure.

3. Always refer to operator's guide instructions

for important details if the snow thrower is to

be stored for an extended period.

4. Maintain or replace safety and instruction la-

bels, as necessary.

5. Run the snow thrower a few minutes after

throwing snow to prevent freeze-up of the

anger/impeller.

F-021033L 11

ASSEMBLY

Read and follow the assembly and adjustment

instructions for your snow thrower. All fasteners

are in the parts bag. Do not discard any parts or

material until the unit is assembled.

_k WARNING: Before doing any

assembly or maintenance to the

snow thrower, remove the wire

from the spark plug.

NOTE: In this instruction book, left and right

describe the location of a pert from the oper-

ator's position behind the unit.

NOTE: Torque is measured in foot pounds

(metric N.m). This measurement describes

how tight a nut or bolt must be. The torque is

measured with a torque wrench.

NOTE: Illustrations begin on page 2.

NOTE: Fasteners and loose parts are shown

at full size in Figure 35.

Tools Required

1 Knife

1 Pliers

2 1/2 inch open end wrenches

2 9/I 6 inch open end wrenches

2 3/4 inch open end wrenches

1 Measuring tape or ruler

1 Screwdriver

How To Remove The Snow Thrower

From The Carton

1. (Figure 1) The snow thrower is shown in the

shipping position.

2. Cut and discard the plastic ties that secure

the crank assembly and the speed control

rod assembly.

3. Cut down ell four corners of the carton and

lay the side panels flat.

4. Locate all parts that are packed separately

and remove from the carton.

5. Remove and discard the packing material

from around the snow thrower.

6. (Figure 2) For shipping purposes, the height

adjust skids (7) are attached to the pallet.

Remove the screw (17) that secures each

height adjust skid (7) to the pallet.

7. Hold onto the lower handle and pull the snow

thrower off the pallet.

CAUTION: DO NOT back over cables.

8. Remove the packing material from the han-

dle assembly.

9. Cut the ties that secure the clutch control

cables (1) to the lower handle (2). Move the

cables away from the motor frame.

How To Assemble The Handle And

Crank Assembly

1. (Figure 3) Loosen, but do not remove, the

fasteners (1) in the upper holes of the lower

handle.

2. Remove the fasteners and the crank assem-

bly eyebolt (11) from the lower holes of the

lower handle.

3. (Figure 2) Put the shift lever (5) into first

forward position.

4. (Figure 3) Raise the upper handle (2) to the

operating position.

F-021033L

NOTE: Make sure the cables are not

caught between the upper and lower han-

dle.

5. Install the fasteners and the crank aseembly

eyebelt (11) that were removed in step 2.

DO NOT tighten until all fasteners are in

place,

6. (Figure 5) Attach the crank rod (15) to the

universal joint assembly (16) with the hair

pin (12).

7. (Figure 3) Tighten nut on eye bolt (11).

Make sure eye belt (11) is properly aligned

and the crank (18) can freely rotate.

8. Tighten ell handle fasteners.

How To Install The Speed Control Rod

1. (Figure 4) Attach the speed control rod (1)

to the speed select bracket (2) with flat-

washer (3) and cotter pin (4).

2. Put the speed select lever (5) into the sixth

gear position.

3. (Figure 8) Rotate the shift yoke assembly

(6) counterclockwise (down) until it stops.

4. The length at the trunnion nut (7) and

speed control rod (1) have been

pre-adjusted at the factory. If an adjustment

is required, loosen the jam nut (12). To

lengthen or shorten the speed control rod

(1), turn the trunnion nut (7) to obtain the

correct length. Tighten the jam nut (12).

5. Align the trunnion nut (7) with the hole in

the shift yoke assembly (6). Fasten with

washer (8) and cotter pin (9).

6. (Figure 4) Mount the hex jam nut (10) onto

the speed select lever (5).

7. Attach the handle (11) onto the speed se-

lect lever (5). To lock in position, tighten the

hex jam nut (10) against the bottom of the

handle (11).

8. Make sure the speed select lever (5) func-

tions correctly. Move the speed select lever

(5) through all speeds.

Remote Chute Knob (Figure 11)

1, Assemble remote chute knob (1) onto lever

(3) until snug against nut (2).

2, Make sure lip (4) on the remote chute knob

(1) is pointed toward the engine,

3, Tighten the nut (2) against the bottom of the

remote chute knob (1).

HOW TO Assemble The Chute Deflector

1. (Figure 6) Remove carriage bolt (1).

2. Raise the chute deflector (2) into operating

position (3).

3. Fasten chute deflector (2) to flange (4) with

carriage bolts (1). Make sure to install with

head of the carriage bolts (1) on the inside

of the flange (2).

4. Fasten with washers (5) and Iocknuts (6).

5. Tighten Iocknuts (6) securely.

NOTE: Make sure all carriage bolts in flange

are tight. DO NOT OVERTIGHTEN.

Check The Cables

1, (Figure 7) Check the traction drive cable

(1) and the auger drive cable (2). If the bot-

tom of the cables have become discon-

nected, reinstall the cables.

12

2. (Figure 9) If the top of the cables (5) have

become disconnected from the drive levers

(6), attach the cables (5) to the "Z" fitting

(7).

How To Set The Skid Height (Figure 2)

The snow thrower is equipped with height ed-

justable skids (7) mounted on the outside of the

auger housing (4). To adjust the height of the

skids, see "How To Adjust The Height Of The

Skids" in the Maintenance section.

How To Set The Length Of The Cables

The cables were adjusted at the factory and no

adjustments should be necessary. However. af-

ter the handles are put in the operating position,

the cables can be too tight or too loose. If an

adjustment is necessary, see "How To Check

And Adjust The Cables" in the Service And Ad-

justment section.

How To Assemble The Drift Cutter

(if equipped)

Drift cutters are used to cut a path through snow

deeper than the auger housing.

1. (Figure 10) Remove the fasteners that se-

cure the drift cutters (1) to the auger hous-

ing.

2. Rotate the drift cutters (1) 180 °,

3. Reinstall the fasteners.

How To Prepare The Engine

NOTE: The engine was shipped from the

factory filled with oil. Cheek the level of the

oil. Add oil as needed.

_lk WARNING: Followthe engine

manufacturer's instructions for the

type of fuel and oil to use. Always

use a safety fuel container. Do not smoke

when adding gasoline to the engine. When

inside an enclosure, do not fill with gaso*

line. Before you add fuel, stop the engine.

Let the engine cool for several minutes.

Check the oil. See the engine manufacturer's

instructions for the type of fuel and oil to use.

Before you use the unit, read the information on

safety, operation, maintenance, and storage.

OPERATION

NOTE: Illustrations begin on page 2.

Know Your Snow Thrower (Figure 2)

Read this Instruction Book and safety rules be-

fore operation the snow thrower, Compare the

illustration with your snow thrower to familiarize

yourself with the location of various controls end

adjustments,

Traction Drive Lever (1) - Select the forward or

reverse direction of travel.

Crank Assembly (2) - Changes the direction of

the discharge chute.

Discharge Chute (3)- Changes the distance the

snow is thrown.

Remote Chute Control (4) -Controls the opera-

tion of the discharge chute.

Auger Drive Lever (5) -Starts and stops the au-

ger and impeller (snow gathering and throwing).

Speed Shift Lever (6) - Selects the speed of the

snow thrower.

Height Adjust Skid (7) - Adjusts the ground

clearance of the auger housing.

Ignition Key (8)- Must be inserted to start the en-

gine.

Primer Button (9) - Injects fuel directly into the

carburetor for fast starts in cold weather.

Electric Start Button (10) -On electric start mod-

els, used to start the engine.

Switch Box (11) - On electric start models, used

to attach a 220 volt electric power cord.

Recoil Starter Handle (12) - Use to manually

start the engine.

Throttle Control (13) - Controls the speed of the

engine,

Choke Control (14) - Use to start a cold engine.

Drift Cutters (18) - (if equipped) Cuts a path

through snow higher than the auger housing.

Shear Bolts (t9)-To protect the machine, special

shear bolts are designed to break is an object be-

comes lodged in the auger housing. The use of a

harder bolt will destroy the protection provided by

the shear bolt.

How To Control

The Discharge Of The Snow

_lk WARNING: Never direct the dis-

charge of snow toward bystanders.

_lk ARNING: Always stop the engine

before unclogging the discharge

chute or the auger housing and be-

fore leaving the snow thrower.

1. (Figure 2) Turn the crank assembly (2) to

change the discharge direction of the snow.

2. (Figure 12) Push the remote chute lever (2)

forward to discharge the snow high and far.

Pull the remote chute lever (2) back to dis-

charge the snow down.

How To Stop

The Snow Thrower (Figure 2)

1. To stop discharging snow, release the auger

drive lever (5).

2. To stop the wheels, release the traction

drive lever (1).

3. To stop the engine, push the throttle control

lever (13) to off and remove the ignition key

(5).

How To Go Forward or Backward

(Figure 2)

1. To change the ground speed, first release the

traction drive lever (1) and then move the

speed shift lever (6) to the desired speed.

2. Ground speed is determined by snow condi-

tions. Select the speed by moving the speed

shift lever (5) into the appropriate notch on

the shift lever plate.

Speed 1,2 Wet, Heavy

Speed 3 Light

F-021033L

Speed 4 Very Light

Speed 5, 6 Transport only

3. To go forward, engage the traction drive

lever (1). Maintain a firm hold on the handle

as the snow thrower starts to move forward.

Guide the snow thrower by moving the han-

dle either left or right. Do not attempt to push

the snow thrower.

4. To go backward, release the tractor drive

lever (1).

5. Move the speed shift lever (5) into either

first or second reverse.

6. Engage the traction drive lever (1).

IMPORTANT: Do not move the speed shift

lever (6) while the traction drive lever (1) is

engaged.

How To Throw Snow (Figure 2)

1. Engage the auger drive lever (5).

2. To stop throwing snow, release the auger

drive lever (5).

_k ARNING: The operation of any

snow thrower can result in foreign

objects being thrown into the eyes,

which can result in severe eye damage.

Always wear safety glasses or eye shields

while operating the snow thrower. We rec-

ommend standard safety glasses or use a

wide vision safety mask over your glasses.

HOW TO Use The Wheel Lockout

(Figure 28)

The right wheel is secured to the axle with a

lockout pin. The unit was shipped with the lock-

out pin in the locked position. For ease of ma-

neuverability in light snow conditions, disconnect

the lockout pin as follows.

1. Pull the knob (1) out to disengage the lock-

out pin.

2. To lock in the disengaged position, turn the

knob (1) 1/4 turn (90 degrees).

Before Starting The Engine

1. Before you service or start the engine, famil-

iarize yourseff with the snow thrower. Be

sure you understand the function and loca-

tion of all controls.

2. Chock the tension of the clutch cable before

starting the engine. See "How To Adjust The

Clutch Cable" in the Maintenance section of

this manual.

3. Make sure that all fasteners are tight.

4. Make sure the beight adjust skids are proper-

ly adjusted. See "How To Adjust The Height

Of The Skids" in the Maintenance section of

this manual.

5. Chock the air pressure in the tires. The cor-

rect air pressure is 14 PSI (1 BAR) to 17 PSI

(t.25 BAR). Do not exceed the maximum

amount of air pressure shown on the side of

the tire.

How To Stop The Engine (Figure 2)

To stop the engine, move the throttle control

(3) to the stop position and remove the ignition

key (5). Keep the ignition key (5) in a safe

place. The engine will not start without the igni-

tion key (8).

13

How To Start The Engine (Figure 2)

Models equipped with an Electric Starter

NOTE: An electric starter kit can be added to

recoil start engines. Electric starter kits are

available from your nearest authorized ser-

vice center.

_k ARNING: The starter is equipped

with a three-wire power cord and

plug and is designed to operate on

220 volt A.C. household current. The power

cord must be properly grounded at all times

to avoid the possibility of electrical shock

which can injure the operator. Carefully fol-

low all instructions in the "How To Start The

Engine" section. Make sure that your house

wiring is a three-wire grounded system. If

you are not sure, ask a licensed electrician.

If your house wire system is not a

three-wire grounded system, do not use

this electric starter under any conditions. If

your system is grounded but a three-hole

grounded receptacle is not available to start

the engine, have a three-hole grounded re.

ceptacle installed by a licensed electrician.

To connect a 220 volt A.C. power cord, al-

ways connect the power cord to the switch

box (11) on the engine first. Then, plug the

other end into the three-hole grounded re-

ceptacle. When disconnecting the power

cord, always unplug the end from the

three-hole grounded receptacle first.

How To Start A Cold Engine (Figure 2)

1. Check the engine oil.

2. Fillthe fuel tank with regular unleaded petrol.

See "Row To Prepare The Engine".

3. Make sure the traction drive lever (1) and

the auger drive lever (5) are in the disen-

gaged (released) position.

4. Move the throttle control (13) to the fast

position.

5. Insert the ignition key (8) into the ignition

slot. Make sure the ignition key (8) snaps

into place. Do not turn the ignition key (5).

Remove the extra ignition key and keep in a

safe place.

6. Move the choke control (14)tothe full

choke position.

7. (Electric Start) Connect the power cord to

the switch box (11) located on the engine.

8. (Electric Start) Plug the other end of the

power cord into a three-hole, grounded 220

VOLT, A.C. receptacle. (See the WARNING

in this section).

9. Push the primer button (9). Every time you

push the primer button (9), wait two sec-

onds. For the number of times required to

push the primer button (9), see the engine

manufacturer's instructions.

lO.(Electric Start) Push on the electric start

button (10) until the engine starts. Do not

crank for more than 10 seconds at a time.

The electric starter is thermally protected. If

the electric starter overheats, itwill automati-

cally stop and can only be restarted when it

has cooled to a safe temperature. A wait of

about 5 to 10 minutes is required to allow the

electric starter to cool.

11.(Recoil Start) Rapidly pull the recoil starter

handle (12). Do not allow the recoil starter

handle (12) to snap back. Slowly return the

recoil starter handle (12).

12.If the engine does not start in 5 or 5 tries.

See the "Trouble Shooting Chart" Instruc-

tions.

13.(ElectricStart) When the engine starts, re-

lease the electric start button (10) and

move the choke control (14) to 1/2 choke

position. When the engine runs smoothly,

move the choke control (14) to the Off posi-

tion.

14.(Electric Start) First disconnect the power

cord from the three-hole receptacle. Then,

disconnect the power cord from the switch

box (11).

NOTE: In temperatures below 0°F, allow

the engine to warm up for several minutes

before blowing snow.

15.When throwing snow, always run the engine

with the throttle control (13) in the fast posi-

tion.

,_ WARNING: Never run the engine

indoors or in enclosed, poorly ven-

tilated areas. Engine exhaust con-

tains carbon monoxide, an odorless and

deadly gas. Keep hands, feet, hair and

loose clothing away from any moving parts

located on the engine or the snow thrower.

The temperature of muffler and nearby

areas may exceed 150°F. Avoid these

areas.

How To Start A Warm Engine (Figure 2)

If an engine has been running and is still warm,

leave the choke control (14) in the off position

and do not push the primer button (9). If the

engine fails to start, follow the instructions "How

To Start A Cold Engine".

NOTE: Do not use the primer button (9) to

start a warm engine.

How To Start An Engine With A Frozen Electric

Starter (Figure 2)

If the electric starter is frozen end will not turn

the engine, follow the instructions below.

1. Pull out the recoil starter handle (12) as far

as possible.

2. Quickly release the recoil starter handle

(12). Allow the recoil starter handle (12) to

snap back against the recoil starter.

If the engine still fails to start, repeat the two pre-

vious steps until the engine starts. Then, contin-

ue with the directions "How To Start A Cold

Engine".

To help prevent the possible freeze-up of the

recoil starter and of the engine controls, proceed

as follows after each snow removal job.

1. With the engine running, quickly pull the re-

coil starter handle (12) three or four times

with a continuous full arm stroke. This will

produce a loud clattering sound that is not

harmful to the engine or starter.

2. Stop the engine. Wipe all snow and moisture

from the carburetor cover, control levers and

cables. Also move the throttle control (13),

choke control (14), and recoil starter han-

dle (12) several times.

How To Remove Snow or Debris From

The Auger Housing (Figure2)

_k ARNING: Do not attempt to re-

move snow or debris that may be-

come lodged in auger housing

without taking the following precautions.

1, Release the auger drive lever (5),

2. Move the throttle control (13) to the stop

position.

3. Remove (do not turn) the ignition key (8).

4. Disconnect the spark plug wire.

5. DO not place your hands in the auger hous-

ing (4) or the discharge chute (3). Use a

pry bar to remove any snow or debris.

Snow Throwing Tips

1. Far maximum snow thrower efficiency,

change the ground speed, NEVER change

the engine speed. The engine is designed to

deliver maximum performance at full throttle

and must be run in the fast position at all

times. In deep, freezing, or wet snow, reduce

forward speed. If the wheels slip, else reduce

forward speed.

2. Most efficient snow throwing is accomplished

when the snow is removed immediately after

ff falls.

3. For complete snow removal, slightly overlap

each previous path.

4. Whenever possible, discharge the snow

down wind.

5. For normal usage, set the skids so that the

scraper bar is 1/8" above the skids. For ex-

tremely hard-packed snow surfaces, adjust

the skids upward so that the scraper bar

touches the ground.

6. Rocks and gravel must not be picked up and

thrown by the machine. On gravel or crushed

rock surfaces, set the skids at I-1/4 inch be-

low the scraper bar. See "How To Adjust The

Height Of The Skids" in the Maintenance

section.

7. After each snow throwing job, allow the en-

gine to idle for e few minutes. The snow and

accumulated ice will melt off the engine.

8. Clean the snow thrower after each use.

9. Remove ice, snow end debris from the entire

snow thrower. Flush with water to remove all

salt or other chemicals. Wipe snow thrower

dry.

F-021033L 14

CUSTOMER RESPONSIBILITIES

SERVICE RECORDS

MAINTENANCE CHART

Fill in dates as you Before First Every Every Every

complete regular Each 2 5 10 25 Each Before

service. Use Hours Hours Hours Hours Season Storage SERVICE DATES

Change Engine Oil _/

_i_,.

Check Spark Plug _/

Check Fuel

Check Auger Clutch Cable Adjustment

(See Cable Adjustment)

Lubricate All Pivot Points

4

ii__i'!#__!__ii¸is°_i___m¸_',1¸i¸!ii¸¸_i_'i¸!ii__i_i¸i¸¸i_ii_iiii_ili¸¸_.i!!_ii_ilii_ii!ii¸ii¸!_i!iili!¸i__!iii!ii'lli!i_i!._ii_ii_!i!i!i!i¸!i!i_¸!!!i!ii¸i_¸i!¸ii_!!!_i¸_ii_ii.ii!_!i!_ii!i!iil¸i¸i_i!ii,ii_ii¸!_iii!_i_!i!._ii!i!i_ii_ii_i¸!i_i_¸_!i.iiii!il_i!!iiiii!!i¸!iii_i!¸ii_!!_ii¸ii!!!_:!!.!i¸i!!i!!i!_ii_i__i_i_i¸ii_ii!!if!ii!ii¸'!i¸i¸¸i__!__ii__i¸i¸!i_!i_iii_i¸!!_ii_ilii_ii!ii¸ii¸!_i!iili!¸i__!iii!ii'lli!i_i!ii¸ii¸iililii!ii¸iiiili:iiii!iiil¸_!ii¸!il!iii¸_i!:ili_ii¸i!ii:iii_ii¸i!ii:iii_ii¸i!ii:iii_ii¸i!ii:iii_ii¸i!ii:iiiiii!ii

Lubricate Drive Chains end Sprockets _ _/

MAINTENANCE

NOTE: Illustrations begin on page 2.

Use the following maintenance section to keep

your unit in good operating condition. All the

maintenance information for the engine is in the

engine manufacturer's instructions. Before you

start the engine, read this book.

_k ARNING: Before you make an in-

spection, adjustment (except

carburettor), or repair, disconnect

the wire from the spark plug.

General Recommendations

The warranty on this snow thrower does not cov-

er items that have been subjected to operator

abuse or negligence. To receive full value from

the warranty, the operator must maintain the

snow thrower as instructed in this manual.

Some adjustments must be made periodically to

propedy maintain the snow thrower.

After Each Use

• Check for any loose or damaged parts.

• Tighten any loose fasteners.

• Check end maintain the auger.

• Check controls to make sure they ere

functioning properly.

• If any parts are worn or damaged, replace

immediately.

All adjustments in the Maintenance section of

this manual should be checked at least once

each season.

F-021033L

As Required

The following adjustment should be preformed

more than once each season.

1. Adjust the auger drive belt after the first 2 to

4 hours, again at mid-season, and twice

each season thereafter. See "How To Adjust

The Auger Drive Belt" in the Maintenance

section.

Lubrication

Every 10 Hours (Figure 17)

1, LubdcatetheZerkfittings (1) everyten

hours with a grease gun.

2. Each time a shear bolt is replaced, the auger

shaft must also be greased.

3. Lubricate ell pivot points.

Every 25 Hours

Chute Rotation Gear

(Figure 5) Lubricate the chute rotation gear (1)

with automotive type oil,

Chains

1, (Figure 2) Move the speed shift lever (6) to

first gear.

2, Remove the gas from the gas tank. Stand

the snow thrower up on the front end of the

auger housing (4).

_k ARNING: Drain the gasoline out-

doors, away from fire or flame.

3, (Figure 24) Loosen the bolts (3) on each

side of the bottom panel (2),

15

4, Remove the bottom panel (2).

5, (Figure 18) Lubricate the chains (5) with a

chain type lubricant.

6, Wipe the hexshaft and sprockets (6) with

5W30 motor oil,

NOTE: If grease or oil come in contact

with the disc drive plate (1) or the friction

wheel (3), damage can result. Clean off

any oil or grease with a alcohol base sol-

vent.

7, (Figure 24) Install the bottom panel (2).

8, Tighten the bolts (3) on each side of the bot-

tom panel (2).

Items Not To Lubricate (Figure 18)

1, De not lubricate the hex shaft and sprock-

ets (6). All bearings and bushings are life-

time ]ubdcated. For storage, put a slight

amount of 5W-30 motor oil on a cloth and

wipe the hex shaft and sprockets (6) to

prevent rust.

2. If grease or oil comes in contact with the

disc drive plate (1) or the friction wheel

(3), the friction wheel (3) can be damaged.

Make sure to thoroughly clean the disc drive

plate (1) and the friction wheel (3).

CAUTION: Any greasing or oiling of the

above components can cause contamina-

tion of the friction wheel (3). If the disc

drive plate (1) or the friction wheel (3) be-

come contaminated with grease or oil,

damage to the friction wheel will result.

3. The auger gear case is lubricated at the fac-

tory and does not require additional lubrica-

tion. If for some reason the lubricant leaks

out, have the auger gear case checked by a

factory authorized service center.

How To Adjust The Height Of The Skids

(Figure 2)

This snow thrower is equipped with two height

adjustable skids (7). These skids elevate the

front of the snow thrower. For normal hard sur-

faces, such as a paved driveway or walk, adjust

the skids as follows.

1. Put the snow thrower on e level surface.

2. Make sure both tires are equally inflated.

The correct air pressure is 14 PSI (1 BAR) to

17 PSI (1.25 BAR). Do not exceed the maxi-

mum amount of air pressure shown on the

side of the tire.

3. Put the extra shear bolts (found in the parts

bag) under each end of the scraper bar (15)

next to the adjustable skids (7).

4. Loosen the mounting nuts (15) that hold the

adjustable skids (7). To bring the front of the

snow thrower down, raise each adjustable

skids (7). Tighten the mounting nuts (16).

NOTE: For rocky or uneven surfaces, raise

the front of the snow thrower by moving the

adjustable skids (7) down.

_lk ARNING: Be certain to maintain

proper ground clearance for the

area to be cleared. Objects such

as gravel, rocks or other debris, if struck

by the impeller, can be thrown with suffi-

cient force to cause personal injury, prop-

erty damage or damage to the snow throw-

HOW TO Adjust

The Scraper Bar (Figure 2)

After considerable use, the scraper bar (15) will

become worn. The scraper bar (15), in con-

junction with the skids, must be adjusted to allow

1/8 inch clearance between the scraper bar

(15) and the sidewalk or area to be cleared.

1. Put the snow thrower on e level surface.

2. Make sure both tires are equally inflated.

The correct air pressure is 14 PSI (1 BAR) to

17 PSI (1.25 BAR). Do not exceed the maxi-

mum amount of air pressure shown on the

side of the tire.

3. Loosen the carriage bolts and nuts that hold

the scraper bar (15) to the auger housing

(4).

4. Adjust the scraper bar (15) to allow 1/8 inch

clearance between the scraper bar (15) end

the sidewalk or area to be cleared.

5. Tighten the carriage bolts and nuts. Make

sure that the scraper bar (15) is parallel with

the sidewalk or area to be cleared.

6. To extended the life of the scraper bar (15),

remove end reverse the mounting of the

scraper bar (15).

How To Remove The Snow Hood

To access the spark plug, the snow hood must

be removed as follows:

1. (Figure 13) Remove the choke control

knob (1).

2. Remove the ON/OFF key (2).

3. Remove the four mounting screws (5).

4. (Figure 14) Slowly remove the snow hood

(4). Make sure that the primer button hose

and the ignition wire are not disconnected.

5. To install the snow hood (4), first make sure

that the primer button hose and the ignition

wire are connected.

F-021033L

6. (Figure 15) Mount the snow hood (4) to the

engine and secure with the four mounting

screws.

7. (Figure 16) Align the tab (5) on the choke

control knob (6) with the slot (7) in the

snow hood.

8. Connect the choke control knob (5) with

the choke shaft (7). Make sure the choke

control knob (5) is propedy installed. If the

choke control knob (6) is not installed cor-

rectly, the choke wii] not operate.

How To Check And Adjust The Cables

The traction drive cable and the auger drive

cable are adjusted at the factory. During normal

use, a cable can become stretched and must be

checked and adjusted as follows.

How To Check The Cables (Figure 19)

1. TOcheck for correct adjustment, disconnect

the "Z" fitting (1) from the drive lever (2).

2. Move the drive lever (2) forward until the

drive lever (2) is contacting the plastic

bumper (3).

3. The control cable is correctly adjusted if the

center of the "Z" fitting (1) isaligned (4)

with the hole in the drive lever (2) and there

in no droop in the cable.

How To Adjust The Auger Drive Cable

1. Remove the gas from the gas tank. Stand

the snow thrower up on the front end of the

auger housing.

,_ WARNING: Drain the gasoline out-

doors, away from fire or flame.

2. (Figure 19) Diseennect the "Z" fitting (1)

from the drive lever (2).

3. (Figure 20) Pull the spring cover up to ex-

pose the spring (5). Push the cable (6)

through the spring (5) to expose the square

end (7) on the cable (6).

4. Hold the square end (7) with pliers and ad-

just the Iocknut (8) in or out until the excess

slack is removed.

5. Pull the cable (5) back through the spring

(5).

6. (Figure 19) Connect the "Z" fitting (1) to the

drive lever (2).

NOTE: When the auger drive belt is adjusted

or replaced, check end adjust the cable.

How To Adjust The Traction Drive Cable

1. Remove the gas from the gas tank. Stand

the snow thrower up on the front end of the

auger housing.

,_ WARNING: Drain the gasoline out-

doors, away from fire or flame.

2. (Figure 24) Loosen the bolts (3) on each

side of the bottom panel (2).

3. Remove the bottom panel (2).

4. (Figure 19) Disconnect the "Z" fitting (1)

from the traction drive lever (2).

5. (Figure 30) Slide the cable boot (3) off the

cable adjustment bracket (4).

6. Push the bottom of the traction control

cable (5) through the cable adjustment

bracket (4) until the "Z" hook (5) can be re-

moved.

16

7. Remove the "Z" hook (6) from the cable

adjustment bracket (4). Move the "Z" hook

(6) down to the next adjustment hole.

8. Pull the traction control cable (5) up

through the cable adjustment bracket (4).

9. Put the cable boot (3) over the cable ad-

justment bracket (4).

lO.(Figure 19) Install the "Z" fitting (1) to the

traction drive lever (2).

11.(Figure 18) To check the adjustment, de-

press the drive lever and check the length

"A" of the drive spring (7). In correct adjust-

ment, the length "A" of the drive spring (7)

is as follows:

minimum 3 inches (76 mm.)

maximum 3-3/8 inches (85 mm.),

12.(Figure 24) Install the bottom panel (2).

13.Tighten the bolts (3) on each side of the bot-

tom panel (2).

HOW TO Adjust The Belts

The belts will stretch during normal use. If you

need to adjust the belts due to wear or stretch,

proceed as follows.

How To Adjust The Auger Drive Belt

If the snow thrower will not discharge snow,

check the adjustment of the auger drive cable.

See "How To Check And Adjust The Cables" in

the Maintenance section, if the adjustment is

correct, then check the condition of the auger

drive belt. If the auger drive belt is damaged,

replace the auger drive bolt. See "How To Re-

place The Belts" in the Maintenance section, if

the auger drive belt is loose, adjust as follows.

1. Disconnect the spark plug wire.

2. (Figure 21) Remove screw (2) from belt

cover (1). Remove the belt cover (1).

3. (Figure 22) Loosen the nut (2) on the idler

pulley (3) Move the idler pulley (3) 1/8 inch

toward the auger drive belt (4).

4. Tighten the nut (2).

5. (Figure 23) Depress the auger drive lever.

Check the tension on the auger drive belt

(4). In correct adjustment, the auger drive

belt (4) will deflect 1/2 inch (5) with moder-

ate pressure. If the adjustment is not correct,

repeat the adjustment.

6. (Figure 21) install the belt cover (1). Tighten

screw (2).

7. Check the adjustment of the auger drive

cable. See "How To Check And Adjust The

Cables" in the Maintenance section.

8. Attach the spark plug wire.

Traction Drive Belt

The traction drive belt has constant spring pres-

sure and does not require an adjustment. If the

traction drive bolt is slipping, replace the belt.

See "How To Replace The Belts" in the Mainte-

nance section.

How To Replace The Belts

The drive belts ere of special construction and

must be replaced with original factory replace-

ment belts available from your nearest autho-

rized service center.

Some steps require the assistance of a second

person.

How To Remove the Auger Drive Belt

If the auger drive belt is damaged, the snow

thrower will not discharge snow. Replace the

damaged belt as follows.

1.Disconnectthesparkplug wire.

2. (Figure 24) Loosen the bolts (3) on each

side of the bottom panel (2).

3. Remove the bottom panel (2).

4. (Figure 21) Remove screw (2) from belt

cover (1). Remove the belt cover (1).

5. (Figure 22) Loosen the belt guide (9). Pull

the belt guide (9) away from the auger

drive pulley (10).

6. Pull the idler pulley (3) away from the au-

ger drive belt (4).

7. Remove the old auger drive belt (4) from

the auger drive pulley (10) end from the en-

gine pulley (11). Replace the auger drive

belt (4) with an original factory replacement

belt available from an authorized service

center.

8. Install the new auger drive belt (4) onto the

auger drive pulley (10) and onto pulley

(11).

9. Adjust the auger drive belt (4). See "How To

Adjust The Auger Drive Belt" in the Mainte-

nance section.

10.Adjust the belt guide (9). See "How To Ad-

just The Belt Guide" in the Maintenance sec-

tion.

11.(Figure 21) Install the belt cover (1). Tighten

screw (2).

12.Check the adjustment of the cables. See

"How To Check And Adjust The Cables" in

the Maintenance section.

13.Connect the spark plug wire.

How To Remove the Traction Drive Belt

If the snow thrower will not move forward, check

the traction drive belt for wear or damage. If the

traction drive belt isworn or damaged, replace

the belt as follows.

1. Disconnect the spark plug wire.

2. Remove the auger drive belt. See "How To

Remove The Auger Drive Belt" in the Mainte-

nance section.

3. (Figure22) Removethe e-ring (17) from

one end of the swing plate axle rod (18).

Remove the swing plate axle rod (18) to

allow the the swing plate to pivot forward.

4. Remove the traction drive spring (16).

5. Remove the old traction drive belt (13) from

the traction drive pulley (14) and from the

engine pulley (15). Replece the traction

drive belt (13) with an original factory re-

placement belt available from an authorized

service center.

6. Install the new traction drive belt (13) onto

the traction drive pulley (14) and onto en-

gine pulley (15).

7. Make sure the traction drive idler pulley

(12) is properly aligned with the traction

drive belt (13).

8. Attach the traction drive spring (16).

9. Install the swing plate axle rod (18) end se-

cure with the e-ring (17) removed earlier.

lO.(Figure 33) The bottom of the swing plate

(20) must be positioned between the align-

merit tabs (19). Make sure the swing plate

(20) is properly secured.

NOTE: It the drive will not engage after

the traction drive belt has been replaced,

then check to make sure that the swing

plate is positioned between the alignment

tabs (19).

F-021033L

11.(Figure 22) Install and adjust the auger

drive belt (4). See "How To Remove The

Auger Drive Belt" in the Maintenance section.

12.Adjust the belt guide (5). See "How To Ad-

just The Belt Guide" in the Maintenance sec-

tion.

13.(Figure 24) Install the bottom panel (2).

14.Tighten the bolts (3) on each side of the bot-

tom panel (2).

15.(Figure 21) Install the belt cover (1). Tighten

screw (2).

16.Check the adjustment of the cables. See

"How To Check And Adjust The Cables" in

the Maintenance section.

17.Connect the spark plug wire.

How To Adjust The Belt Guide

1. Disconnect spark plug wire.

2. (Figure 21) Remove screw (2). Remove the

belt cover (1).

3. (Figure 2) Engage the auger drive lever (5).

4. (Figure 25) Measure the distance between

the belt guide (2) and auger drive belt (3).

The correct distance (4) is 1/8 inch (3.175

ram),

5. If an adjustment is necessary, loosen the

mounting bolt for the belt guide (2). Move

the belt guide (2) to the correct position

(4). Tighten the mounting bolt for the belt

guide (2).

6. (Figure 21) Install the belt cover (1). Tighten

screw (2).

7. Connect the spark plug wire.

How To Adjust Or Replace The Friction

Wheel

How To Check The Friction Wheel

If the snow thrower will not move forward, check

the traction drive belt, the traction drive cable or

the friction wheel. If the friction wheel is worn or

damaged, it must be repleced. See "How To

Replace the Friction Wheel" in this section. If the

friction wheel is not worn or damaged, check as

follows.

1. (Figure 2) Remove the gas from the gas

tank. Stand the snow thrower up on the front

end of the auger housing (4).

_k ARNING: Drain the gasoline out-

doors, away from fire or flame.

2. Disconnect the spark plug wire.

3. (Figure 24) Loosen the bolts (3) on each

side of the bottom panel (2).

4. Remove the bottom panel (2).

5. (Figure 2) Position the shift speed lever (6)

in the lowest forward speed.

6. (Figure 26) Note the position of the friction

wheel (4). The correct distance "A" from the

right side of the friction wheel (4) to the out-

side of the motorbox is as follows:

Tire Size Distance "A"

12 and 13 inch 4-1/8" (10.5 cm.)

16 inch 4-5/t6" (10.95 cm.)

If the friction wheel (4) is not in the correct

position, adjust as follows.

How To Adjust The Friction Wheel

1. (Figure 2) Position the shift speed lever (6)

in the lowest forward speed.

17

2. (Figure 8) Remove washer (8) and cotter

pin (9) that connect the trunnion nut (7) to

the shifter rod (1). Remove the trunnion

nut (7) from the shifter rod (1).

3. (Figure 26) Move the friction wheel (4) to

the correct position.

4. (Figure 8) Tum the trunnion nut (7) until it is

aligned with the mounting hole in the shifter

rod (1). When aligned, attach the trunnion

nut (7) and secure with washer (5) and cot-

ter pin (5).

5. (Figure 24) Install the bottom panel (2).

6. Tighten the bolts (3) on each side of the bot-

tom panel (2).

How To Replace The Friction Wheel

If the friction wheel iswom or damaged, the

snow thrower will not move forward. The friction

wheel must be replaced as follows.

1. (Figure 2) Remove the gas from the gas

tank. Stand the snow thrower up on the front

end of the auger housing (4).

_k ARNING: Drain the gasoline out-

doors, away from fire or flame.

2. Disconnect the spark plug wire.

3. (Figure 31) Remove the fasteners that se-

cure the left wheel (10). Remove the left

wheel (10) from the axle (11).

4. Loosen the bolts (3) on each side of the bot-

tom panel (2).

5, Remove the bottom panel (2).

6, (Figure 32) Remove the fasteners that se-

cure the drive sprocket (12) to the axle (11).

7, Remove the right wheel, axle (11), end drive

sprocket (12).

8, (Figure 33) Remove the four bolts (16) that

holdthe bearings (7) on each side of the

hex shaft (8).

9, (Figure 34) Remove the hex shaft (8) end

bearings (7).

NOTE: Take special note of the position of

the washers (17).

lO.(Figure 29) Remove the three fasteners (4)

that hold the friction wheel (5) to the hub

(6).

11.(Figure 29) Remove the friction wheel (5)

from the hub (6). Slip the friction wheel (5)

off the hax shaft (8).

12.Assemble the new friction wheel (5) onto

hub (6) with the fasteners removed eedier.

13.(Figure 34) install the hax shaft (8) and

bearings (7) with the four bolts removed ear-

lier.

Make sure the washers (17) are properly

installed in the original position. Also,

make sure the two washers (13) are prop-

erly aligned with the actuator arms (14).

14.Make sure the hex shaft (8) turns freely.

15.(Figure 32) Install the right wbeel, axle (11),

and drive sprocket (12) with the fasteners

removed earlier. Install the chain (15) onto

the drive sprocket (12).

16.Check the adjustment of the friction wheel.

See "How To Adjust The Friction Wheel" in

this section.

17.Make sure the fdction wbeel and the disc

drive plate are free from grease or oil.

18.(Figure 24) Install the bottom panel (2).

19.Tighten the bolts (3) on each side of the bot-

tom panel (2).

20.Install the left wheel (10) to the axle (11)

with the fasteners removed earlier.

21.Connectthesparkplugwire.

How To Replace the Auger Shear Bolt

The augers are secured to the auger shaft with

special shear bolts. These shear belts ere de-

signed to break and protect the machine ff an

object becomes lodged in the auger housing.

Do not use a harder bolt as the protection pro-

vided by the shear bolt will be lost.

_k ARNING: For safety and to pro-

tect the machine, use only original

equipment shear bolts.

To replace a broken shear bolt, proceed as fol-

lows. Extra shear bolts were provided in the as-

sembly parts beg.

1. (Figure 2) Move the throttle control (13) to

the stop position. Disengage all controls.

2. Disconnect the spark plug wire. Make sure

ell moving parts have stopped.

3. (Figure 17) Lubricate the auger shaft Zerk

fitting (1), if equipped, with a grease gun.

4. (Figure 27) Align the hole inthe auger with

the hole in the auger shaft. Install the new

shear bolt (2), spacer (3), and Iocknut (4).

5. Connect the spark plug wire.

HOW TO Prepare The Snow Thrower For

Storage

,_ WARNING: Do not remove gasoline

while inside a building, near a fire,

or while you smoke. Gasoline

fumes can cause an explosion or a fire.

1. Drain the fuel tank.

2. Let the engine run until it is out of gasoline.

3. Drain the oil from the warm engine. Fill the

engine crankcase with new oil.

4. Remove the spark plug from the cylinder.

Pour one ounce of oil into the cylinder. Slow-

ly pull the recoil-start grip so that the oil will

protect the cylinder. Install a new spark plug

in the cylinder.

5. Thoroughly clean the snow thrower.

6. Lubricate all lubrication points. See the Main-

tenance section.

7. Be sure that ell nuts, bolts end screws are

securely fastened. Inspect all visible moving

parts for damage, breakage and wear. Re-

place if necessary.

8. Cover the bare metal parts of the blower

housing, auger, and the impeller with spray

rust preventative lubricant.

9. Put the unit in a building that has good ven-

tilation.

10. If the machine must be stored outdoors.

block up the snow thrower to be sure the en-

tire machine is off the ground.

11.Cover the snow thrower with a suitable pro-

tective cover that does not retain moisture.

Do not use plastic.

How To Order Replacement Parts

The replacement parts ere shown either on the

back pages of this Instruction Book or in a sepa-

rate Parts List Book.

Use only manufacturer's authorized or approved

replacement parts. The letter placed on the end

of the part number denotes the type of finish for

the part, C for chrome, Z for zinc, a PA for pur-

chased assembly. It is important that you include

this when ordering a part. Do not use attach-

ments or accessories not specifically recom-

TROUBLE SHOOTING CHART

mended for this unit. in order to obtain proper

replacement parts you must supply the model

number (see nameplate).

Replacement parts, except for the engine, trans-

mission, transaxle or differential, are available

from the store where the product was pur-

chased, a service shop recommended by the

store or from a"Murray, Inc. Central Parts Dis-

tributor" listed on the back page of this Instruc-

tion Book.

If you are unable to obtain parts or service in the

manner outlined above, then contact:

HAY'rER LIMITED,

Service Department,

Spellbrook,

Bishop's Stortford,

Hertfordshire. CM23 4BU.

MURRAY, INC.

Outdoor Power Equipment

Customer Service Department

P.O. Box 268

Brentwood, Tennessee U.S.A. 37027

1-800-251-8007 Collect telephone calls will not

be accepted.

Replacement parts for the engine, transaxle, or

transmission, are available from the manufectur-

er's authorized service centre found in the yel-

low pages of the telephone directory. Also, see

the individual engine or transmission warranties

to order replacement parts.

When ordering the following information is re-

quired:

(1) The Model Number

(2) Serial Number

(3) Part Number

(4) Quantity

TROUBLE

Difficult starting

CAUSE

Defective spark plug,

Wateror dirt in fuel system,

Unit fails to discharge snow

Engine runs erratic Blocked fuel line, empty gas tank. or stale

gasoline

Engine stalls Unit running on CHOKE.

Engine runs erratic; Water or dirt in fuel system.

Loss of power

Excessive vibration Loose parts: damaged impeller

Unit fails to propel itself Drive belt loose or damaged.

Incorrect adjustment of traction drive cable

Worn or damaged friction wheel.

Auger drive belt loose or damaged.

Auger control cable not adjusted correctly.

Shear bolt broken

Discharge chute clogged.

F-021033L

Foreign object lodged in auger

18

CORRECTION

Replace spark plug.

Use carburetor bowl drain to flush and refill with

fresh fuel.

Clean fuel line; check fuel supply; add fresh

gasoline

Set choke lever to RUN position.

Use carburetor bowl drain to flush and refill with

fresh fuel.

Stop engine immediately and disconnect spark

plug wire. Tighten all bolts and make all

necessary repairs. If vibration continues, have

the unit serviced by a competent repairman.

Replace drive belt.

Adjust traction drive cable.

Replace friction wheel.

Adjust auger drive belt; replace if damaged.

Adjust auger control cable.

Replace shear bolt

Stop engine immediately and disconnect spark

plug wire. Clean discharge chute and inside of

auger housing.

Stop engine immediately and disconnect spark

plug wire. Remove object from auger.

SOMMAIRE

INFORMATIONS SUR LE PRODUIT

INFORMATIONS DESTINEES AU PROPRIETAIRE

PICTOGRAMMES INTERNATIONAUX

MONTAGE

FONCTIONNEMENT

MAINTENANCE

TABLEAU DE MAINTENANCE

TABLEAU DE DEPANNAGE

20

21

23

24

26

30

Q

GARANTIE LIMITEE DE DEUX ANS

Murray, Inc. garantie aupr_s de racheteur initial

qua cette machine est d_pourvue de d_fauts

mat6riels at de construction sous utilisation et

entretien normaux pendant une dur_e de deux

(2) ans& partir de la date d'acquisitian ; cette

garantie cependant ne cauvre pas les mateurs,

accessoires (tels qua moteurs _lectriques) et

pi_ces d'usure normale (except_es les pi_ces

mentionn_es ci-dessous) 6tant donn_ que les

soci_t6s fabriquant ces articles offrent leurs

propres garanties at fournissent des r6parations

par lebiais de leurs centres de maintenance

specialists agr_s. Pour plus d'infarmations, se

reporter aux garanties couvrant ces pi_ces

particuli_res. Si vous ne savez pas si votre

machine cantient ou est 6quip_e d'une au

plusieurs de ces pi_ces, adressez vous a votre

revendeur avant I'acquisition. Sous r_serve des

madalit_s et conditions de cette garantie limit_e,

nous nous engageons & r_parer ou remplacer, &

notre discr6tian et gratuitement aupr_s de

I'acheteur initial, taute piece cauverte par cette

garantie limit_e jusqu'& I'expiration de la garantie

applicable.

Les pi_ces d'usure normale camprennent les

courraies d'entrainement, les fraises

h_licafdales, les goupilles de cisaillement, les

pneumatiques, etles phares. Ces pi_ces sont

garanties sans d_faut materiel ou de

construction dans 1'6tat o_ elles ant _t6 livr_es

avec ]e produit. Toute r_clamation concernant la

r_paration au le remplacement d'une piece

d'usure narmale dolt _tre effectu_e darts les

trente (30) jaurs suivant la date d'acquisition.

Aucune r_clamation ne sara honor_e

concemant des dommages provenant de la

simple utilisation, d'un usage abusif, ou d'une

mauvaise utilisatian.

Cette garantie Murray, Inc. de deux (2) arts

constitue votre recours exclusff ; cepondant,

cette garantie est nulle ou ne s'applique pas aux

machines ayant 6t_ madifi_es, endornmag_es,

fait robjet d'une utilisation abusive, ou utilis6es

lots d'une location au a des fins cammerciales

F-021033L

et/ou professionnelles (autre que domestiques).

Votre garantie ne couvre pas les r_glages

m_caniques mineurs non dus & des d6fauts

materiels de fabrication. Consultez votre manuel

d'utilisation pour obtenir une assistance

concernant ces r_giages.

Pour effectuer une r_clamation sous la garantie

limit_e de deux (2) ans Murray, Inc., retourner

la machine, (ou, suivant notre autorisation

pr6alable, la piece d_fectueuse) accompagn6e

de votre preuve d'achat, aupr_s du Centre de

maintenance agr_6 ]e plus proche de chez vous.

Pour Iocaliser le centre de maintenance le plus

proche, contactez le Distdbuteur de pi_ces

r_gional de votre r_gion figurant sur la liste

fournie avec votre machine, ou consultez les

pages jaunes de votre annuaire t61_phonique

local. Si vous nous retournez la machine

complete, nous r_parerons celle-ci. Si nous

autorisons seulement le retour de la pi6ce

d_fectueuse, nous effectuerons soit la r6paration

de celle-ci, salt son remplacement. Cette

garantie limitee Murray, Inc. de deux (2) arts

vous octroie des droits I_gaux sp_cifiques, et

vous pouvez _galement vous pr6valoir d'autres

droits dont le contenu varie selon I'Etat ot_ils

s'appliquent. Cette garantie limit_e eat

d_livr_e en lieu et place de toute garantie

stipul_e ou tacite, ceci incluant la garantie

tacite de commerciabilite et la garantie de

fonctionnalit_ pour une t&che d_finie. Si

vous souhaitez recevoir des informations

suppl_mentaires concernant carte garantie

_crite ou une assistance quant & robtention de

services de r_paration, adressez=vous & :

HAYTER LIMITED,

Service Department,

Spellbrook,

Bishop's Stortford,

Hertfordshire. CM23 4BU.

MURRAY, INC.

Outdoor Power Equipment

Customer Service Department

P.O. Box 268

Brentwood, Tennessee U.S.A. 37027

1-800=251-8007

19

INFORMATIONS SUR LE PRODUIT

Le propri6taire dolt _tre certain qce tousles

renseignements sur le produit sent inclus avec

la tondecse. Ces renseignements comprennent

les MANUELS D'INSTRUCTION, les PIECES

DE RECHANGE, et les GARANTIES. Ces

renseignements doivent 6tre inclus pour

s'asscrer que les lois d'Etat et les autres lois

sont observ6s.

INFORMATIONS DESTINEES AU

PROPRIETAIRE

Ce manuel se dirige aux personnes familiaris6es

avec ce genre de manipulations m_caniques. La

plupart des ouvrages de maintenance ne

mentionnent pas toutes les _tapes, et cet

ouvrage ne fait pas exception. Serrer ou

desserrer des attaches sent des manipulations

que tout le monde peut effectuer avec une

certaine pratique. Lisez et suivez ces

instructions avant d'utiliser la tondecse.

Apprenez b maitriser I'appareil : si vous

comprenez ]e fonotionnement de oe mod&le,

vous en obtiendrez les meiUecres performances.

Au fur et b mesure que vous lisez le manuel,

reportez-vous aux illustrations. Sachez rep_rer

I'emplacement des commandes et leur fonction.

Afin de pr6venir tout risque d'accident, observez

les instructions de fonctionnement et les r6gles

de s_curit_. Conservez ce manuel pour future

r_f_rence.

IMPORTANT : De nombrecx appareils ne sent

pas assembles et sent vendus d_mont_s dans

lecr carton d'emballage. IIest alors de la

responsabilit6 du propri_taire de veiller & ce qce

les instructions de montage pr_sentes dans le

manuel soient suivies en toute exactitude.

D'autres appareils sont vendus enti_rement

months. En ce qui conceme les machines d_j&

mont_es, il est de la responsabilit_ du

propri6taire de veilier ace que la machine soit

correctement assembl_e. Le propri6taire doit

v_rifier attentivement la machine en fonction des

instructions pr6sentes dans le manuel avant de

commencer &utiliser celle-cL

DANGER : rep_rez ce symbole qui voes

indiquera les precautions de s_curit_ im-

porfantes. Ce symbole signifie : "Attention!

Soyez prudent! Vous encourrez des ris-

ques."

Responsabilite de rutilisateur

La responsabilite de I'utilisateur est de

suivre les instructions ci-dessous.

1, Life soigneusement oe manuel et suivre les

r_gles indiqu_es pour un usage de la ton-

deuse en toute s_curit6.

2. Suivre les instructions de montage et de

preparation.

Q

3. Inspecter ]a tondeuse.

4. S'asscrer que rutilisatecr de la tondeuse

salt bien utiliser les _quipements standards

et les accessoires.

5. N'utiliser la tondeuse qu'avec les 6quipe-

ments de protection, les _crans et autres

dispositifs de s_curit_ bien en place et en

bon _tat de marche.

6. Proceederaux r_glages n_cessaires.

7. Entretenir la tondeuse avec les pi_ces de

rechange autods6es ou agr_es.

8. Veiller & ce qu'un entretien complet soit ef-

fectu_ scr la tondeuse.

Prise de conscience environnementale

• Ne pas remplir le r_servoir d'essence du

moteur au ras-bord.

• Vider I'essence pendant le remisage hors

saison.

• N'utiliser qce de ressence sans plomb.

• Entretenir r_guli6rement le filtre a air.

• Changer I'huile r_guli6rement. Utiliser de

rhuile de grade 5W-30.

• Effectuer un r6glage du moteur r_guli6re-

ment.

• Conserver le mat6riel en bon 6tat de mar-

che.

• Eliminer I'huile de vidange de fagon 6colo-

gique.

mURRAY

MODEL NO.: 629904x54A

SKU No.:

YYYY MM DD:

SERIAL NO.:

3700 min-1

129 kg

Manufactured in Lawrenceburg, TN 38464, U.S.A.

Niveaux de vibration d_clar_s conformes &ceux d_finis par la directive

europ_enne 98/37/CE.

Niveaux de vibration relev_s conform_ment a la norme

EN 1033;1996 : 10,6 m/s2.

Valeurs determin_es sur les brae de la tondeuse en station immobile sur une

surface ciment_e &un r_gime de 3700 min-1.

Niveaux de bruit de LWA108 dR declares conformes & ceux d_finis par la

directive europ_enne 2000/14/CE, Annexe V.

Niveau de pression acoustique a la station de rutilisateur 86 dB.

R_sultats & I'oreille obtenus en application de la norme EN ISO 11201.

F-021033L 20

Sivu latautuu ...

Murray 629904X54A Instruction book

Murray 629904X54A Instruction book

muilla kielillä

Liittyvät paperit

Muut asiakirjat